Add EHCI controller and USB command definition.
Signed-off-by: NXie Xiaobo <r63061@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

If CONFIG_LBA48 is not defined, the element lba48 of struct sata_dev_desc
is not avaible, and can't be used.
Signed-off-by: NTang Yuantian <b29983@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

MPC8536 Rev 1.0 silicon have NMG_eSDHC118 erratum, so that the SDHC write
protected pin polarity does not follow the SD card standard in MPC8536
Rev 1.0 silicon.

The MPC8536DS board invert the SDHC_WP pin as a workaround.  However, this
silicon erratum has been fixed in Rev 1.1, So need invert the SDHC_WP
polarity again when use the MPC8536 Rev1.1 and greater on MPC8536DS board.
Signed-off-by: NXie Xiaobo <r63061@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
   so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
   to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.
Signed-off-by: NXie Xiaobo <r63061@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- Increase the size of malloc space.
- Enable e1000 network card.
- Show pci devices on startup.
- Change the location of env address.
- Use hwconfig to turn off ECC by default.

[Kumar Gala] Fixed white space formating for CONFIG_EXTRA_ENV_SETTINGS
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

We really shouldn't be overwriting bat registers with translation enabled,
especially when we're executing code using one of them for translating
the current instruction stream.  Instead, disable address translation
while doing the final BAT setup.

In order to do this, setup_bats has to move back to asm code, because we
require translation to be enabled to have a stack for C code.  The yucky
thing about that is that the assembler doesn't like ULL so we have to
switch to using HIGH/LOW pairs for physical addresses that are > 32 bits
in length.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Acked-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

There were duplicate (and conflicting) defines for the BATs used
to cover SRIO.  Drop the bogus set.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.

During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used.  In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.

We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

It is not necessary to keep multiple entries for the same setting in DDR
speed tables. Merge them for smaller tables. Also restructure the tables
for smaller size. Cleanup some typedefs.

Enforce strict checking for speed table. If DIMM is running at higher than
known speed, try to use the highest speed setting. If rank is unknown, it
has to panic.

Removed ODT overriding for P2020DS as it is not necessary.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Teranetics PHY does not properly report the link state
for fiber connections. The new PHY code actually checked the link,
and so the FM driver would refuse to talk over a linkless PHY.

But the link may actually be up, so now we always report it as up
for fiber connections on the tn2020.
Signed-off-by: NAndy Fleming <afleming@freescale.com>

The macro CONFIG_ENABLE_36BIT_PHYS is used to indicate that the given SOC is
capable of 36-bit physical addresses, even if such large addresses are not
used.  On two boards, this macro was enabled only when building a 36-bit
image.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.

To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:

setenv ddr_interactive on

After reset, U-boot prompts before initializing DDR controllers
FSL DDR>

The available commands are
print      print SPD and intermediate computed data
reset      reboot machine
recompute  reload SPD and options to default and recompute regs
edit       modify spd, parameter, or option
compute    recompute registers from current next_step to end
next_step  shows current next_step
help       this message
go         program the memory controller and continue with u-boot

The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:768:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>

Fix:
usb.c: In function 'usb_parse_config':
usb.c:331:17: warning: variable 'ch' set but not used [-Wunused-but-set-variable]
usb.c: In function 'usb_hub_port_connect_change':
usb.c:1123:29: warning: variable 'portchange' set but not used [-Wunused-but-set-variable]
usb.c: In function 'usb_hub_configure':
usb.c:1183:25: warning: variable 'hubsts' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: NRemy Bohmer <linux@bohmer.net>

Fix:
ohci-hcd.c: In function 'dl_transfer_length':
ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: NRemy Bohmer <linux@bohmer.net>

Fix:
cmd_usb.c: In function 'usb_show_tree_graph':
cmd_usb.c:284:29: warning: variable 'port' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: NRemy Bohmer <linux@bohmer.net>

Fix:
smc91111.c: In function 'smc_phy_configure':
smc91111.c:1194:6: warning: variable 'failed' set but not used [-Wunused-but-set-variable]
smc91111.c:1190:7: warning: variable 'phyaddr' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix:
jffs2_1pass.c: In function 'jffs2_1pass_read_inode':
jffs2_1pass.c:699:7: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
jffs2_1pass.c: In function 'jffs2_1pass_build_lists':
jffs2_1pass.c:1578:14: warning: variable 'empty_start' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix:
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:225:6: warning: unused variable 'devices_found'
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
[-Wunused-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: NStefan Roese <sr@denx.de>

Fix:
board.c:445:8: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

Esp. while printing the environment the output is usually longer than 512
bytes. Instead of cutting the message, send multiple 512 bytes packets.
Signed-off-by: NMichael Walle <michael@walle.cc>
Acked-by: NMike Frysinger <vapier@gentoo.org>

The 'time' command runs and reports execution time of commands.

Sample usage:
--------------------
u-boot# time crc 0x1000 1000
CRC32 for 00001000 ... 00001fff ==> ae94dc4b

time: 0.004 seconds, 4 ticks
--------------------
Signed-off-by: NChe-Liang Chiou <clchiou@chromium.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Reported-by: NMichael Jones <michael.jones@matrix-vision.de>
Signed-off-by: NWolfgang Denk <wd@denx.de>

Some previous changes added code right in the middle of the
description of CONFIG_SHOW_BOOT_PROGRESS.  Move this text down.
Fix formatting while we are at it.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Also rearrange IH_TYPE table slightly.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Add support for SERIAL MULTI for uartlite.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

While adding asm/cache.h to common.h for PPC targets, I got an
error about multiple definitions of some DBSR_ macros. While
scanning these defines, I noticed that some where defined not
correctly for all PPC variants. So I removed all unused defines,
and corrected the ones really used by bedbug (book-e vs. ppc40x).
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

This is needed for the patch "cache: add default setting for
CONFIG_SYS_CACHELINE_SIZE" from Anton Staaf. As cache.h defines
CONFIG_SYS_CACHELINE_SIZE for PPC targets.

This will remove the following warnings/errors:

include/common.h:819:2: warning: #warning CONFIG_SYS_CACHELINE_SIZE not defined, using __BIGGEST_ALIGNMENT__
cache.c:33: error: '__BIGGEST_ALIGNMENT__' undeclared (first use in this function)
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Anton Staaf <robotboy@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>

Previous output:
Marvell>>  mmc part

Partition Map for MMC device 1  --   Partition Type: EFI

Part  Start LBA  End LBA
gpt1  0x8C00    0xCBFF
gpt2  0xCC00    0x57BFF
gpt3  0x57C00    0xA2BFF
gpt4  0xA2C00    0xECBFDE

With the patch, the output becomes:
Marvell>> mmc part

Partition Map for MMC device 1  --   Partition Type: EFI

Part    Name                    Start LBA       End LBA
  1     ramdisk                 0x00008C00      0x0000CBFF
  2     system                  0x0000CC00      0x00057BFF
  3     userdata                0x00057C00      0x000A2BFF
  4     remaining               0x000A2C00      0x00ECBFDE
Signed-off-by: NLei Wen <leiwen@marvell.com>

mkimage's ublimage support can't depend of build-time board configs;
instead, this should be set in ublimage.cfg.  Since currently no configs
in u-boot override the NAND block size, hardcode it as such in
ublimage.h to fix a build failure with "make tools":
gcc [...] -o ublimage.o ublimage.c -c
In file included from ublimage.c:37:0:
ublimage.h:31:20: fatal error: config.h: No such file or directory

Cc: Heiko Schocher <hs@denx.de>
Cc: patches@linaro.org
Signed-off-by: NLoïc Minier <loic.minier@linaro.org>
Acked-by: NHeiko Schocher <hs@denx.de>

Generate timestamp_autogenerated.h as safely as version_autogenerated.h.

Cc: patches@linaro.org
Signed-off-by: NLoïc Minier <loic.minier@linaro.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Tools such as mkimage include version information but are
config-agnostic; build timestamp_autogenerated.h even when config.mk
isn't generated to fix "make tools" build failure:
gcc [...] -o mkimage.o mkimage.c -c
In file included from include/version.h:27:0, from mkimage.c:26:
include/timestamp.h:27:37: fatal error: timestamp_autogenerated.h: No
such file or directory

Cc: patches@linaro.org
Signed-off-by: NLoïc Minier <loic.minier@linaro.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

The generated file asm-offsets.s may be found at various depths in the
arch subdirectories, so simply ignore it throughout the tree.
Signed-off-by: NLaurence Withers <lwithers@guralp.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Introduce CONFIG_SPL_START_S_PATH to configure path to start.S file. It's not
always fitting to use CPU's start.S .
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

cmd_sf.c: In function 'do_spi_flash':
cmd_sf.c:164:9: warning: 'skipped' may be used uninitialized in this function
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NSimon Glass <sjg@chromium.org>

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This driver was never converted to NET_MULTI, and no board uses it.
So punt it and be done.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These drivers have never been converted to NET_MULTI, and they are only
used by one board (BMW).  So drop the drivers until someone feels like
rewriting them for NET_MULTI support.

Rather than punting the BMW board completely, just disable net support
in its board config.  Seems to build fine without it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Now that we've got boards.cfg and most people have converted over,
start warning people who have yet to so we can phase board configs
completely out of the Makefile.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>