- 01 4月, 2015 2 次提交
-
-
由 Bo Shen 提交于
Enable SPL support for at91sam9n12ek boards, now it supports boot up from NAND flash, serial flash. Signed-off-by: NBo Shen <voice.shen@atmel.com>
-
由 Wu, Josh 提交于
Insteading in mmc's raw sectors, this patch will save the environment in a fat file (uboot.env) in mmc card's first FAT patition by default. If you want to save in mmc's raw sectors, you only need to define CONFIG_ENV_IS_IN_MMC. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Acked-by: NBo Shen <voice.shen@atmel.com>
-
- 19 9月, 2014 1 次提交
-
-
由 Wu, Josh 提交于
Signed-off-by: NJosh Wu <josh.wu@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 27 5月, 2014 2 次提交
-
-
由 Wu, Josh 提交于
As at91 board config file will include the SoC header, so we can remove the ARM926EJS definition in board config files. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Wu, Josh 提交于
Now the AT91FAMILY is already defined in the at91 SoC header. The at91 board config file will include the SoC header file. So we can remove the redundant AT91FAMILY definition in at91 board config files. Signed-off-by: NJosh Wu <josh.wu@atmel.com> [rebase patch] Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 09 12月, 2013 1 次提交
-
-
由 Andreas Bießmann 提交于
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com> Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de> Acked-by: NScott Wood <scottwood@freescale.com>
-
- 05 11月, 2013 3 次提交
-
-
由 Bo Shen 提交于
Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Bo Shen 提交于
Add usb host support for at91sam9n12ek board. Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Rob Herring 提交于
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
- 22 8月, 2013 1 次提交
-
-
由 Bo Shen 提交于
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot to flash the rootfs, in order to avoid flash one sector with all 0xff into NAND, so use nand trimffs subcommand to avoid it Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 24 7月, 2013 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: NTom Rini <trini@ti.com>
-
- 25 6月, 2013 1 次提交
-
-
由 Bo Shen 提交于
add network support with ksz8851_16mll on at91sam9n12ek board Signed-off-by: NBo Shen <voice.shen@atmel.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 12 5月, 2013 1 次提交
-
-
由 Wu, Josh 提交于
Add support for following features: - nand boot, with PMECC 2bit ECC for 512 bytes sector - SPI flash boot - SD card boot - LCD support Signed-off-by: NJosh Wu <josh.wu@atmel.com> [fix -Wimplicit-function-declaration for at91_lcd_hw_init()] Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 12 3月, 2013 2 次提交
-
-
由 Bo Shen 提交于
Change nand flash partition table according to www.at91.com/linux4sam more information: http://www.at91.com/linux4sam/bin/view/Linux4SAM/GettingStarted#Linux4SAM_NandFlash_demo_MemorySigned-off-by: NBo Shen <voice.shen@atmel.com> [minor commit message changes] Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Nicolas Ferre 提交于
Support to boot zImage Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> [Add bootz for at91rm9200, at91sam9263, at91sam9rl] Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 12 1月, 2013 1 次提交
-
-
由 Bo Shen 提交于
Add dataflash boot support on at91sam9x5ek board Signed-off-by: NBo Shen <voice.shen@atmel.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 10 12月, 2012 2 次提交
-
-
由 Richard Genoud 提交于
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com> Acked-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Richard Genoud 提交于
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com> Acked-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 28 11月, 2012 1 次提交
-
-
由 Wu, Josh 提交于
Signed-off-by: NJosh Wu <josh.wu@atmel.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
- 17 10月, 2012 1 次提交
-
-
由 Wu, Josh 提交于
Signed-off-by: NJosh Wu <josh.wu@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 18 9月, 2012 1 次提交
-
-
由 Bo Shen 提交于
The mainline linux kernel is moving to flatten device tree support Add the CONFIG_OF_LIBFDT option to support booting DT linux kernel Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 01 9月, 2012 4 次提交
-
-
由 Wu, Josh 提交于
Signed-off-by: NJosh Wu <josh.wu@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Bo Shen 提交于
Add at91sam9x5 series spi flash boot support Using at91sam9x5ek_spiflash to configure, then it can boot from at25df321 serial flash SPI mater work in 30Mhz speed, while not 1Mhz speed. This will base on atmel_spi patch, or else, it will occur receive overrun Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Bo Shen 提交于
Remove CONFIG_ARCH_CPU_INIT, no need it anymore Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Bo Shen 提交于
Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: NBo Shen <voice.shen@atmel.com> [move MAINTAINERS entry to right place] Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 07 7月, 2012 1 次提交
-
-
由 Bo Shen 提交于
Enable EHCI support instead OHCI Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 21 6月, 2012 2 次提交
-
-
由 Tom Rini 提交于
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: NTom Rini <trini@ti.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Tom Rini 提交于
We provide a default table of { 9600, 19200, 38400, 57600, 115200 } in <config_fallbacks.h> which mkconfig places after <configs/...h> in the generated config file. This is used when a board has not set its own table. Signed-off-by: NTom Rini <trini@ti.com>
-
- 20 4月, 2012 1 次提交
-
-
由 Marek Vasut 提交于
$ git grep AUTOSCRIPT include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPT Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: NAnatolij Gustschin <agust@denx.de>
-
- 27 1月, 2012 1 次提交
-
-
由 Scott Wood 提交于
NAND_MAX_CHIPS has been replaced by CONFIG_SYS_NAND_MAX_CHIPS, and the latter defaults to 1. Signed-off-by: NScott Wood <scottwood@freescale.com>
-
- 29 11月, 2011 1 次提交
-
-
由 Stelian Pop 提交于
Change my old email address which is no longer valid. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 28 11月, 2011 1 次提交
-
-
由 Stelian Pop 提交于
Change my old email address which is no longer valid. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 06 10月, 2011 1 次提交
-
-
由 Mike Frysinger 提交于
Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 04 9月, 2011 1 次提交
-
-
由 Thomas Petazzoni 提交于
Based on earlier work by Alex Waterman <awaterman@dawning.com>. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
-
- 30 10月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
For ARM systems, before ELF relocation was introduced, CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the U-Boot image from whereever it was loaded to it's link address (CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation was performed at all, it was just a memcpy(). With ELF relocation, this does not work like that any more, and related boards need to be fixed anyway. So don't keep this relict any longer. Signed-off-by: NWolfgang Denk <wd@denx.de> Tested-by: NHeiko Schocher <hs@denx.de> Tested-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
- 27 10月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-by: NKumar Gala <galak@kernel.crashing.org>
-
- 08 3月, 2010 1 次提交
-
-
由 Achim Ehrlich 提交于
Configuration defines should be preceeded with CONFIG_SYS_. Renamed some at91 specific defines to conform to this naming convention: AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK Signed-off-by: NAchim Ehrlich <aehrlich@taskit.de>
-
- 13 2月, 2010 2 次提交
-
-
由 Jens Scharsig 提交于
* add a real AT91 GPIO driver instead of header inline code * resolve the mixing of port and pins * change board config files to use new driver * add macros to gpio to realize backward compatibility Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>
-
由 Jens Scharsig 提交于
* add's the new temporary CONFIG_AT91_LEGACY to all board configs This will need for backward compatiblity, while change the SoC access to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated SoC is used. Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>
-
- 09 12月, 2009 1 次提交
-
-
由 Heiko Schocher 提交于
There is more and more usage of printing 64bit values, so enable this feature generally, and delete the CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL defines. Signed-off-by: NHeiko Schocher <hs@denx.de>
-