This converts the following to Kconfig:
   CONFIG_CMD_BMP
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_BMODE
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_BLOB
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_BEDBUG
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_BAT
Signed-off-by: NSimon Glass <sjg@chromium.org>

This looks like a typo. Fix it.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_AES
   CONFIG_AES
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Add select AES to CMD_AES]
Signed-off-by: NTom Rini <trini@konsulko.com>

This option is not used in U-Boot. Drop it.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This is only used by one board and should not be a CONFIG option. Instead
it should use the driver model pmic framework. For now, just move the
setting into the only board that uses it.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_PMIC_AS3722
Signed-off-by: NSimon Glass <sjg@chromium.org>

Most of the PMICs are in the drivers/power/pmic/ directory. Move this one
there.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Before converting this to Kconfig, rename it to match the other PMICs.
Signed-off-by: NSimon Glass <sjg@chromium.org>

A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig.  Do so now.
Signed-off-by: NTom Rini <trini@konsulko.com>

Xilinx fixes for v2017.05

- Fix usbotg on Miami board
- Cleanup zc1751 defconfig

In file ext4fs.c funtion ext4fs_read_file() compares an
unsigned expression with < 0 like below

	lbaint_t blknr;
	blknr = read_allocated_block(&(node->inode), i);
	if (blknr < 0)
		return -1;

blknr is of type ulong/uint64_t. read_allocated_block() returns
long int. So comparing blknr with < 0 will always be false. Instead
declare blknr as long int.

Similarly ext4/dev.c does a similar comparison. Drop the redundant
comparison.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Update Keystone2 secure device configs under
"TI SYSTEM SECURITY". Without this buildman keeps complaining
about the status of these boards.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NAndrew F. Davis <afd@ti.com>

On ARM v7M, the processor will return to ARM mode when executing
a blx instruction with bit 0 of the address == 0. Always set it
to 1 to stay in thumb mode.

Tested on STM32f746-disco board

Similar commit:
f99993c1
Author: Matt Porter <mporter@konsulko.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.

Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

CONFIG_CMD_FS_UUID was neither whitelisted, nor was it declared in
Kconfig.
Now it can be enabled in .config and defconfig as expected.
Signed-off-by: NJosua Mayer <josua.mayer97@gmail.com>

Almost all TI defconfigs enable this already, add this as a default
and remove the explicit assignment.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Finally adding support for ARC boards in TravisCI.

To build for ARC boards we need to install Synopsys prebuilt toolchain
which we do here.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3,
DRA71 supports the following OPPs for various voltage domains:

VDD_MPU:	OPP_NOM
VDD_CORE:	OPP_NOM
VDD_GPU:	OPP_NOM
VDD_DSPEVE:	OPP_NOM, OPP_HIGH
VDD_IVA:	OPP_NOM, OPP_HIGH

This patch add support for selection of the above OPPs instead of
using OPP_NOM for all voltage domains.

[1] http://www.ti.com/lit/ds/symlink/dra718.pdfReported-by: NVishal Mahaveer <vishalm@ti.com>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

This originally started out as
     "pinctrl: Kconfig: reorder to keep Rockchip options together"
and tried to keep the Rockchip-related config options together.

However, we now rewrite all chip-specific driver selections to start
with CONFIG_PINCTRL_ (with the inadvertent changes to related
Makefiles) and sort those alphabetically. And as this already means
touching most of the file, we also reformat the help text to not exceed
80 characters (but make full use of those 80 characters).
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: NSimon Glass <sjg@chromium.org>

An assignment (of a value to itself) was left over (after removing and
addition from the line) from moving the common padding code into
rkcommon_vrec_header.

This change removes this to avoid a spurious warning in static code
analysis (i.e. Coverity).
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reported-by: Coverity (CID: 161418)
Reviewed-by: NTom Rini <trini@konsulko.com>

These were reminders that somehow slipped through the cracks
or were erroneously introduced after previous clean-ups.

Getting rid of then once again. Hopefully for good now :)

Where missing and appropriate replace with CONFIG_CMDLINE_EDITING
which really enables shell history as of now.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Jon Mason <jon.mason@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

There are more and more cases where if we do not use gcc-6.0 or later we
run into problems where our binaries are too large for the targets.
Given the prevalence of gcc-6.0 or later toolchains at this point in
time, we give notice now that starting with v2018.01 we will require
gcc-6 (or later) for ARM.
Signed-off-by: NTom Rini <trini@konsulko.com>

Unfortunately a test for the PWM uclass was not included when it was
submitted. This was noticed when trying to add more functionality:

   http://patchwork.ozlabs.org/patch/748172/

Add a simple test to get us started.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Standardise U-Boot prompt on all keystone2 platforms
instead of platform specific prompt.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The name of the gpio bank under DM_GPIO appear to be a copy-paste error.
This changes the name of the gpio bank from am33xx_gpios to omap34xx_gpios.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The register names and offset were not correct as per the TRM for OMAP3530
and OMAP3630.  Correct the naing and offsets per the documentation
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>

Remove option which depends on MMC controller which is disabled for dc2.
Savedefconfig is removing it because of new dependencies.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Fixes the following problem:
zynq-uboot> run dfu_ram
Setting bus to 1
g_dnl_register: failed!, error: -19

The cause appears to be that the USB framework is looking for a usbotg aliases,
so add the alias to point to our USB device.
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

We used to have opencoded ehci_readl()/writel() which required no
external functions to be called.

Now with attempt to switch to generic readl()/writel() accessors
we see a missing declaration of those accessors in ehci-ppc4xx.
Something like that happens if applied
http://patchwork.ozlabs.org/patch/726714/:
---------------->8---------------
  CC      drivers/usb/host/ehci-ppc4xx.o
drivers/usb/host/ehci-ppc4xx.c: In function 'ehci_hcd_init':
drivers/usb/host/ehci-ppc4xx.c:23:3: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]
   HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
   ^
---------------->8---------------
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: NStefan Roese <sr@denx.de>

For id = 15 an out of bound access occurs in udc_setup_ep().
Increase the size of epinfo[] from 30 to 32 to encompass
ids 0..15.

The problem was highlighted by cppcheck.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

We want to check the result of musb_init_controller
and not the address were the result is stored.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Add support for the Terasic DE10-Nano board.  The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Reviewed-by: NDinh Nguyen <dinguyen@kernel.org>