Add support for the DEKA Research and Development galaxy5200 board

The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: NEric Millbrandt <emillbrandt@dekaresearch.com>

Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: NReinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NStefan Roese <sr@denx.de>

The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards.  Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Board support for the Guntermann & Drunck DL-Vision.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This is Marvell's 88F6281_A0 based reference design board

This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product

This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: NRonen Shitrit <rshitrit@marvell.com>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported

Note: to boot Kirkwood kernel with USB support,
	you should add "usb start" in the boot sequence
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: NTsiChung Liew <tsicliew@gmail.com>

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>

ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.

More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.htmlSigned-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: NStefano Babic <sbabic@denx.de>

This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Acked-by: NFabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NHoan Hoang <hnhoan@i-syst.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: NSrikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: NTravis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

MECP5123 is a MPC5121E based module by esd gmbh.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>

ARIA is a MPC5121E based COM Express module by Dave/DENX.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>

We rename the board so we use a consistent name in U-Boot and in
Linux.  Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>

Initial U-Boot support for the DaVinci DM355 EVM.  This is a board
from Spectrum Digital.  Board docs include schematic and firmware
for its microcontroller:

  http://c6000.spectrumdigital.com/evmdm355/revd/

Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:

  http://focus.ti.com/docs/prod/folders/print/tms320dm355.html

This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART).  In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>

Zoom2 is a new board from Texas Instruments and LogicPD

The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp

This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.

To configure, run
make omap3_zoom2_config
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>

Signed-off-by: NHeiko Schocher <hs@denx.de>

The PM9263 board is based on the AT91SAM9263-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>