- 12 8月, 2019 11 次提交
-
-
由 Igor Opaniuk 提交于
1. Add myself as Android A/B and AVB maintainer 2. Add Sam Protsenko as Designated reviewer for A/B Signed-off-by: NIgor Opaniuk <igor.opaniuk@gmail.com>
-
由 Manivannan Sadhasivam 提交于
Add MAINTAINERS entry for HI3660 SoC by adding the arch includes. While doing so, adding myself as the co-maintainer for HISILICON SoCs since I'm planning to maintain HI3660 SoC separately and considering doing improvements to the existing HiSilicon SoC architecture. Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Manivannan Sadhasivam 提交于
This commit adds MMC driver support for HI3660 SoC reusing hi6220_dw_mmc driver. Since HI3660 operates at different clock rate and uses fifo mode now, let's introduce the platform data and utilize it for different SoCs supported by this driver. Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Manivannan Sadhasivam 提交于
This commit adds board support for Hikey960 board from Hisilicon. This board is one of the Consumer Edition boards of the 96Boards family powered by Kirin960 SoC. More information about this board can be found in 96Boards website: https://www.96boards.org/product/hikey960/ The initial supported/tested devices include: - Debug serial - SD With these support, it's good enough for loading Linux Kernel from SD. Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Manivannan Sadhasivam 提交于
This commit adds devicetree for Hikey960 board. Most of the contents are copied from Linux kernel with some modifications for u-boot. To be more precise, SD card's speed related properties are removed due to a bug in u-boot clock implementation. Hence forcing the SD controller to work in standard speed. Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Manivannan Sadhasivam 提交于
This commit imports HI3660 SoC devicetree from Linux Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Simon Goldschmidt 提交于
This implements a stack usage check in SPL. Many boards start up SPL to run code + data from one common, rather small SRAM. To implement a sophisticated SPL binary size limit on such boards, the stack size (as well as malloc size and global data size) must be subtracted from this SRAM size. However, to do that properly, the stack size first needs to be known. This patch adds a new Kconfig option: - SPL_SYS_REPORT_STACK_F_USAGE: memset(0xaa) the whole area of the stack very early and check stack usage based on this constant later before the stack is switched to DRAM Initializing the stack and checking it is implemented in weak functions, in case a board does not use the stack as saved in gd->start_addr_sp. Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Ye Li 提交于
Should use CONFIG_IS_ENABLED not IS_ENABLED for CLK driver, so it will check the CONFIG_SPL_CLK when building SPL Signed-off-by: NYe Li <ye.li@nxp.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Ley Foon Tan 提交于
This fix issue when access config from PCIe switch. The PCIe controller need to send Type 0 config TLP if the targeting bus matches with the secondary bus number, which is when the TLP is targeting the immediate device on the link. The PCIe controller send Type 1 config TLP if the targeting bus is larger than the secondary bus, which is when the TLP is targeting the device not immediate on the link. Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
-
由 Ley Foon Tan 提交于
Hardware return completion status non-zero when read from non exist function in multi-function PCIe device. Return error will cause PCIe enumeration fail. Change it to return 0 and return value 0xffffffff when error. Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
-
由 Ley Foon Tan 提交于
Some PCIe devices require longer time to response. Increase polling counter to 20000 (~100ms). Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
-
- 11 8月, 2019 2 次提交
-
-
-
git://git.denx.de/u-boot-usb由 Tom Rini 提交于
- DaVinci USB updates - Various OHCI fixes - Gadget fixes
-
- 10 8月, 2019 25 次提交
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-x86由 Tom Rini 提交于
- Enable SD slot on Intel Edison - Populate CSRT ACPI table for shared DMA controller on Intel Tangier - Convert Intel ICH-SPI driver to use new spi-mem ops - Enable config_distro_bootcmd for QEMU x86 - Support U-Boot as a payload for Intel Slim Bootloader - Avoid writing temporary asl files into the source tree which fixes the parallel build issue occasionally seen
-
由 Marek Vasut 提交于
Add board code for the R8A77980 V3H Condor board. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
Add a few bits of platform code to support R8A77980 V3H SoC. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
Import R8A77980 V3H clock tables from Linux 5.2.7 , commit 5697a9d3d55f. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
Import R8A77980 V3H PFC tables from Linux 5.2.7 , commit 5697a9d3d55f. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
Fix various type warnings when building this driver for 64bit machine. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
The R8A77980 V3H gether needs a few minor adjustments to the sh_eth driver, add them to support ethernet on R8A77980. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
-
由 Igor Opaniuk 提交于
Remove obsolete legacy usbboot wrapper, as distroboot can handle booting from USB drivers. Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Marcel Ziswiler 提交于
Support the V1.2 hardware revision with the following pin muxing changes: Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4 are now used as DDC pins. Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are now used as USB power enable signals. Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power enable signals are now used as GPIO3 and GPIO4. Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is loaded on V1.2 and later modules and resp. USB power enable signals activated. Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Dominik Sliwa 提交于
When mainline kernels reboot TK1 they use SW_RESET, that reset mode does not reset PMIC. Some rails need to be off for RAM Re-repair to work correctly. Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NDominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Marcel Ziswiler 提交于
Remove video=tegrafb0:640x480-16@60 aka VESA VGA mode from vidargs in order for the panel specification in the device tree to be used. This causes the default to be the 10.1" LVDS display which will be available in the Toradex webshop shortly. Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Dominik Sliwa 提交于
Display proper reset reason after the SoC info. Signed-off-by: NDominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Igor Opaniuk 提交于
Switch to the generic compressed Kernel image type (zImage) instead of the U-Boot specific uImage format. Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Igor Opaniuk 提交于
Disabling ASPM fixes incompatibilities with some PCIe cards Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NDominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Igor Opaniuk 提交于
Let the kernel print some debug messages when a user program crashes due to an exception. Signed-off-by: NStefan Agner <stefan.agner@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Igor Opaniuk 提交于
Use unified values for USB Product/Vendor numbers when the config block is missing Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NMax Krummenacher <max.krummenacher@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Igor Opaniuk 提交于
Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1 modules. Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NDominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Marcel Ziswiler 提交于
By keeping RESET_MOCI_CTRL low we avoid explicitly releasing RESET_MOCI#. Please note that module hardware versions up to V1.1A will already release RESET_MOCI# in hardware coming out of reset. Please further note that with this change the USB hub on the Apalis Evaluation board is kept in reset in U-Boot and therefore none of its ports are operational in U-Boot. Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Igor Opaniuk 提交于
We never really added a sensible DFU configuration for platforms based on eMMC. Most of the things one might want to do can also be done with UMS or fastboot, so drop the DFU configuration. Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: NPhilippe Schenker <philippe.schenker@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Trent Piepho 提交于
This is a configuration option specific to the tegra controller. Doing it this way makes it show up directly under the tegra controller option, indented one level, as "Disable external clock loopback". The way it is now, it shows up at the end of the controller list, not indented, as if it's some kind of generic MMC configuration option. Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Simon Glass <sjg@chromium.org> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: NTrent Piepho <tpiepho@impinj.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Simon Glass 提交于
For U-Boot we allow a GPIO to be specified to enable the codec. Add this to the relevant binding files. Signed-off-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Simon Glass 提交于
This file was missed when adding the sound driver to U-Boot. Bring it in from Linux 5.0. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NJon Hunter <jonathanh@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Simon Glass 提交于
This file was missed when adding the sound driver to U-Boot. Bring it in from Linux 5.0. Signed-off-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 09 8月, 2019 2 次提交
-
-
由 Park, Aiden 提交于
The setting up MTRRs have already been done in previous Slim Bootloader stages. Signed-off-by: NAiden Park <aiden.park@intel.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com> Tested-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Park, Aiden 提交于
Add slimbootloader board to run U-boot as a Slim Bootloader payload - Add new board/intel/slimbootloader directory with minimum codes - Add slimbootloader configuration files - Add doc/board/intel/slimbootloader.rst Signed-off-by: NAiden Park <aiden.park@intel.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com> Tested-by: NBin Meng <bmeng.cn@gmail.com> [bmeng: add slimbootloader board MAINTAINERS file] Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-