Signed-off-by: NWolfgang Denk <wd@denx.de>

Round clock frequencies for printing.

Many boards printed off clock frequencies like 399 MHz instead of the
exact 400 MHz because numberes were not rounded. This is fixed now.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Commit f7d190b1 corrected the value of MPC85xx_PORDEVSR2_SEC_CFG, but forgot
to add a comment that the correct value disagrees with the 8544 reference
manual.  The changelog for that commit is also wrong, as it says "bit 28"
when it should be "bit 24".
Signed-off-by: NTimur Tabi <timur@freescale.com>

Conflicts:

	drivers/usb/usb_ohci.c

Conflicts:

	board/freescale/mpc8536ds/mpc8536ds.c
	include/configs/mgcoge.h
Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NJason Jin <Jason.jin@freescale.com>

This patch based on Andy's work.
Including command 'pixis_set_sgmii' support.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>

The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.

Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>

Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>

Debug sessions may have left enabled laws.
Changing lawbar with an unkown enabled tgtid could cause problems.
Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>

mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0.
Include host_agent == 0 decode for end-point determination.

This is not needed for the ds reference board since pcie3 will be a host
in order to connect to the uli chip.  Include it here as a reference for
other mpc8572 boards.
Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>

Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>

Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>

Some cores don't support ethernet stashing at all, and some
instances have errata.  Adds 3 properties to gianfar nodes
which support stashing.  For now, just add this support to
85xx SoCs.
Signed-off-by: NAndy Fleming <afleming@freescale.com>

* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
Signed-off-by: NJames Yang <James.Yang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>

* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.

* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.
Signed-off-by: NJames Yang <James.Yang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>

Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>

* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>

Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.

* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>

Fix some bugs:
  1. Correctly set intlv_ctl in cs_config.
  2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
  3. Set base_address and total memory for each ddr controller in memory
     controller interleaving mode.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash.  Instead we can just flush the L1 d-cache and invalidate the i-cache.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache.  This allows us to more efficient change mappings
from cache-able to cache-inhibited.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

in ft_blob_update () for both boards was an unneccessary
repetition of code, which this patch moves in a common
function for this boards.
Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Each architecture has different ways of determine what regions of memory
might not be valid to get overwritten when we boot.  This provides a
hook to allow them to reserve any regions they care about.  Currently
only ppc, m68k and sparc need/use this.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Sub-command can benefit from using the same table and search functions
that top level commands have.  Expose this functionality by refactoring
find_cmd() and introducing find_cmd_tbl() that sub-command processing
can call.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NHeiko Schocher <hs@denx.de>

The EEprom contains some Manufacturerinformation,
which are read from u-boot at boot time, and saved
in same hush shell variables.
Signed-off-by: NHeiko Schocher <hs@denx.de>

This new command shows the local variables defined in
the hush shell:

=> help showvar
showvar
    - print values of all hushshell variables
showvar name ...
    - print value of hushshell variable 'name'

Also make the set_local_var() and unset_local_var ()
no longer static, so it is possible to define local
hush shell variables at boot time. If CONFIG_HUSH_INIT_VAR
is defined, u-boot calls hush_init_var (), where
boardspecific code can define local hush shell
variables at boottime.
Signed-off-by: NHeiko Schocher <hs@denx.de>

With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: NHeiko Schocher <hs@denx.de>

As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.

This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.

This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.

Maybe we should use the approach from Keymile as
the new standard?
Signed-off-by: NHeiko Schocher <hs@denx.de>