- 21 10月, 2008 7 次提交
-
-
由 Wolfgang Denk 提交于
Several customers have reported problems with the environment in EEPROM, including corrupted content after board reset. Probably the code to prevent I2C Enge Conditions is not working sufficiently. We move the environment to flash now, which allows to have a backup copy plus gives much faster boot times. Also, change the default console initialization to 115200 bps as used on most other boards. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Kumar Gala 提交于
mpc8536ds.c: In function 'is_sata_supported': mpc8536ds.c:615: warning: unused variable 'devdisr' Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Round clock frequencies for printing. Many boards printed off clock frequencies like 399 MHz instead of the exact 400 MHz because numberes were not rounded. This is fixed now. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Timur Tabi 提交于
Commit f7d190b1 corrected the value of MPC85xx_PORDEVSR2_SEC_CFG, but forgot to add a comment that the correct value disagrees with the 8544 reference manual. The changelog for that commit is also wrong, as it says "bit 28" when it should be "bit 24". Signed-off-by: NTimur Tabi <timur@freescale.com>
-
-
- 19 10月, 2008 33 次提交
-
-
由 Wolfgang Denk 提交于
Conflicts: board/freescale/mpc8536ds/mpc8536ds.c include/configs/mgcoge.h Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Jason Jin 提交于
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
-
由 Liu Yu 提交于
This patch based on Andy's work. Including command 'pixis_set_sgmii' support. Signed-off-by: NLiu Yu <yu.liu@freescale.com>
-
由 Liu Yu 提交于
The pixis sgmii command depend on the FPGA support on the board, some 85xx boards support SGMII riser card but did not support this command, define CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command. Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and PIXIS_VCFGEN1_MASK in header file for both boards. Signed-off-by: NLiu Yu <yu.liu@freescale.com>
-
由 Ed Swarthout 提交于
Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>
-
由 Ed Swarthout 提交于
Debug sessions may have left enabled laws. Changing lawbar with an unkown enabled tgtid could cause problems. Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>
-
由 Ed Swarthout 提交于
mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0. Include host_agent == 0 decode for end-point determination. This is not needed for the ds reference board since pcie3 will be a host in order to connect to the uli chip. Include it here as a reference for other mpc8572 boards. Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>
-
由 Ed Swarthout 提交于
Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>
-
由 Ed Swarthout 提交于
Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>
-
由 Andy Fleming 提交于
Some cores don't support ethernet stashing at all, and some instances have errata. Adds 3 properties to gianfar nodes which support stashing. For now, just add this support to 85xx SoCs. Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Haiying Wang 提交于
* Add board specific parameter table to choose correct cpo, clk_adjust, write_data_delay based on board ddr frequency and n_ranks. * Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#. Signed-off-by: NJames Yang <James.Yang@freescale.com> Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
-
由 Haiying Wang 提交于
* Add board specific parameter table to choose correct cpo, clk_adjust, write_data_delay, 2T based on board ddr frequency and n_ranks. * Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#. * Set memory controller interleaving mode to bank interleaving, and disable bank(chip select) interleaving mode by default, because the default on-board DDR DIMMs are 2x512MB single-rank. * Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000. Signed-off-by: NJames Yang <James.Yang@freescale.com> Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
-
由 Haiying Wang 提交于
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
-
由 Haiying Wang 提交于
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and ba_intlv_ctl. * Print DDR interleaving mode information * Add doc/README.fsl-ddr to describe the interleaving setting Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
-
由 Haiying Wang 提交于
Because some dimm parameters like n_ranks needs to be used with the board frequency to choose the board parameters like clk_adjust etc. in the board_specific_paramesters table of the board ddr file, we need to pass the dimm parameters to the board file. * move ddr dimm parameters header file from /cpu to /include directory. * add ddr dimm parameters to populate board specific options. * Fix fsl_ddr_board_options() for all the 8xxx boards which call this function. Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
-
由 Haiying Wang 提交于
Fix some bugs: 1. Correctly set intlv_ctl in cs_config. 2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled. 3. Set base_address and total memory for each ddr controller in memory controller interleaving mode. Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Changing the flash from cacheable to cache-inhibited was taking a significant amount of time due to the fact that we were iterating over the full 256M of flash. Instead we can just flush the L1 d-cache and invalidate the i-cache. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Added the ability for C code to invalidate the i/d-cache's and to flush the d-cache. This allows us to more efficient change mappings from cache-able to cache-inhibited. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Heiko Schocher 提交于
in ft_blob_update () for both boards was an unneccessary repetition of code, which this patch moves in a common function for this boards. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Kumar Gala 提交于
Each architecture has different ways of determine what regions of memory might not be valid to get overwritten when we boot. This provides a hook to allow them to reserve any regions they care about. Currently only ppc, m68k and sparc need/use this. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Sub-command can benefit from using the same table and search functions that top level commands have. Expose this functionality by refactoring find_cmd() and introducing find_cmd_tbl() that sub-command processing can call. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
The EEprom contains some Manufacturerinformation, which are read from u-boot at boot time, and saved in same hush shell variables. Signed-off-by: NHeiko Schocher <hs@denx.de>
-