- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 21 1月, 2020 1 次提交
-
-
由 Baruch Siach 提交于
Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Reviewed-by: NStefan Roese <sr@denx.de>
-
- 20 1月, 2020 15 次提交
-
-
由 Fabio Estevam 提交于
Currently the following build warning is seen: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. =================================================== Since the mx7ulp-evk board does not have networking support, explicitly disable networking. Signed-off-by: NFabio Estevam <festevam@gmail.com>
-
由 Arkadiusz Karas 提交于
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support. The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier board has Ethernet, USB host port, USB OTG port. Signed-off-by: NArkadiusz Karas <arkadiusz.karas@somlabs.com> Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Marek Vasut 提交于
Enable SPL SDP fallback boot option in default build. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Vignesh Raghavendra 提交于
Enable USB keyboard to be used as input device at U-Boot prompt. Both serial and USB keyboard will be active inputs simultaneously. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Enable configs related to USB Host mode, Peripheral mode and DFU. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Faiz Abbas 提交于
Add Support for ADMA in a53 and r5 defconfigs. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Adam Ford 提交于
Currently the DM37 and OMAP35 boards do not boot due to SPL bring too large. SPL doesn't need GPIO, I2C nor MMC sector access since it uses a FAT file system. This patch unifies all these boards to remove these unused features from their defconfigs Signed-off-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Andrew F. Davis 提交于
Add new defconfig files for the J721e High Security EVM. These defconfigs are the same as for the non-secure part, except for: CONFIG_TI_SECURE_DEVICE option set to 'y' CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y' CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y' CONFIG_BOOTCOMMAND uses FIT images for booting Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Andrew F. Davis 提交于
Sync new additions to non-HS defconfig with HS defconfig. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Andrew F. Davis 提交于
Sync new additions to non-HS defconfig with HS defconfig. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Enable I2C and EEPROM related configs for A72 SPL/U-Boot. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NAndreas Dannenberg <dannenberg@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Caleb Robey 提交于
Adding the configurations to the evm_defconfig file Signed-off-by: NJason Kridner <jdk@ti.com> Signed-off-by: NCaleb Robey <c-robey@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Faiz Abbas 提交于
Add config to save and read back environment from eMMC. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Faiz Abbas 提交于
Add configs for ADMA Support. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Enable USB host and device related configs. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
- 17 1月, 2020 3 次提交
-
-
由 Patrick Delaunay 提交于
Split the board and SOC support for STM32MP15x family and prepare the introduction of new boards with STM32MP15x. This path define the 2 configurations: - STM32MP15x: STM32MP15x soc support (new) - TARGET_ST_STM32MP15x: STMicroelectronics board support (choice) Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrick Delaunay 提交于
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig for ST board with NOR support (STM32MP15xx-EV1 boards) - CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB) - CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH) This Patch prepares the U-Boot support of boards with STM32MP15x SOC not provided by STMicroelectronics. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Fabio Estevam 提交于
Currently the following build warning is seen: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. =================================================== Since the mx7ulp-evk board does not have networking support, explicitly disable networking. Signed-off-by: NFabio Estevam <festevam@gmail.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
- 16 1月, 2020 7 次提交
-
-
由 Sam Shih 提交于
This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig to fix the mt7623 compile error after building others mediatek target platform Signed-off-by: NSam Shih <sam.shih@mediatek.com> Reviewed-by: NRyder Lee <ryder.lee@mediatek.com>
-
由 Sam Shih 提交于
This adds a general board file based on MT7622 SoCs from MediaTek. This commit is adding the basic boot support for the MT7622 rfb. Signed-off-by: NSam Shih <sam.shih@mediatek.com> Reviewed-by: NRyder Lee <ryder.lee@mediatek.com> Tested-by: NFrank Wunderlich <frank-w@public-files.de>
-
由 mingming lee 提交于
This adds a general board file based on MT8512 SoCs from MediaTek. Apart from the generic parts (cpu) we add some low level init codes and initialize the early clocks. This commit is adding the basic boot support for the MT8512 eMMC board. Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>
-
由 Baruch Siach 提交于
Armada 38x ROM skips the first SD card offset when loading SPL. This affects the location of the main U-Boot image. SPL MMC code now supports U-Boot image offset based on run-time detection of the boot partition. Use this feature to make the same generated image support both SD card and eMMC boot partition. Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Reviewed-by: NStefan Roese <sr@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Baruch Siach 提交于
SPL needs DM GPIO to read the SD card-detect signal. This complements the fix in commit 70bae02f ("arm: mvebu: clearfog: fix boot from SD card"). Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Reviewed-by: NStefan Roese <sr@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Yangbo Lu 提交于
The SDHC clock divider value for LS1028A should be default 2, not 1. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
-
由 Vignesh Raghavendra 提交于
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use macros such as CONFIG_IS_ENABLED() that allow conditional compilation of code for SPL and U-Boot. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 15 1月, 2020 6 次提交
-
-
由 Giulio Benetti 提交于
This commit adds board support for i.MXRT1050-EVK from NXP. This board is an evaluation kit provided by NXP for i.MXRT105x processor family. More information about this board can be found here: https://www.nxp.com/design/development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1050-evaluation-kit:MIMXRT1050-EVK The initial supported/tested devices include: - Debug serial - SD Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>
-
由 Joris Offouga 提交于
Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Joris Offouga 提交于
For DM_ETH support , it's require to disable this config. When this config is enable, This generate a error with spl in linker script Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
Some i.MX8QXP MEK boards do not have MAC address stored and hang during eth driver probe: Error: ethernet@5b040000 address not set. (Board hangs) To fix this problem select CONFIG_NET_RANDOM_ETHADDR so that a valid MAC address can be used in such case. Signed-off-by: NFabio Estevam <festevam@gmail.com>
-
由 Anatolij Gustschin 提交于
Add support for Capricorn Deneb SoM variant. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Add support for i.MX8X based Capricorn Giedi SoM. Supported interfaces: GPIO, ENET, eMMC, I2C, UART. Console output: U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) Trying to boot from MMC1 Load image from MMC/SD 0x3e400 U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07 CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C Model: Siemens Giedi Board: Capricorn Boot: MMC0 DRAM: 1022 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial@5a080000 Out: serial@5a080000 Err: serial@5a080000 Net: eth1: ethernet@5b050000 [PRIME] Autobooting in 1 seconds, press "<Esc><Esc>" to stop Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 14 1月, 2020 7 次提交
-
-
由 Michal Simek 提交于
Qemu v4.2.0 maps bootmode registers to address space which was the reason why board_late_init() was disabled and accesses were failing. With new Qemu board_late_init() can be called without any issue. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
zcu1285 is the same as zcu1275 but it is using Avnet FMC http://www.ultrazed.org/product/network-fmc-module Unfortunately not everything is connected now that's why this is only describing system which Xilinx is using. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
The board is very similar to zcu216 with zu49dr device. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Convert another option Kconfig. Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Decrease amount of the similar defconfigs and use generic one instead. The change was declared by commit 4b37c13d ("arm64: zynqmp: Introduce virtual defconfig") and this patch removes configs for the most of the boards. Utra96/zcu100/zcu102/zcu102 and ZynqMP based System controllers *a2197*. have been also boot tested to make sure that funcionality remains the same. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
These options are taken from zcu102/104 platforms. Also use OF_SEPARATE instead of OF_BOARD. Maybe at some point this option will be taken back but as of now board detection is not ready. export DEVICE_TREE="zynqmp-zcu102-revA" make xilinx_zynqmp_virt_defconfig make -j Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
In past SPL_ZYNQMP_TWO_SDHCI symbol was introduced to handle boards with two sdhci controllers. The problem was that U-Boot is registering controllers based on aliases in DT but bootmode targets specific controller ID. That's why on boards with one "second" sdhci controller bootmode was pointing to second controller(MMC2) but alias was setup to mmc0 (the first controller). And SPL requires to point to mmc0 in this case. Long time ago commit f101e4bd ("spl: add support for alternative boot device") added support for handling multiple bootmodes in SPL. Use this functionality and setup second sdhci controller as backup boot device. Below is table with behavior: HW/bootmode bootorder sd0/sd0 mmc0/mmc1 (mmc1 never called) sd1/sd1 mmc1/mmc0 (mmc0 fails and mmc1 is called) sd0+sd1/sd0 mmc0/mmc1 (mmc1 never called) sd0+sd1/sd1 mmc1/mmc0 (mmc0 never called) All other bootmodes are not affected but order can be extended to cover advance boot flows. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-