- 25 4月, 2012 11 次提交
-
-
由 Liu Gang 提交于
This document describes the implementation of the boot from SRIO, includes the introduction of envionment, an example based on P4080DS platform, an example of the slave's RCW, and the description about how to use this feature. Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
-
由 Liu Gang 提交于
When defined CONFIG_ENV_IS_NOWHERE, there will be some compilation errors: ./common/env_nowhere.o: In function `env_relocate_spec': ./common/env_nowhere.c:38: multiple definition of `env_relocate_spec' ./common/env_flash.o: ./common/env_flash.c:326: first defined here ./common/env_nowhere.o: In function `env_get_char_spec': ./common/env_nowhere.c:42: multiple definition of `env_get_char_spec' ./common/env_flash.o:./common/env_flash.c:78: first defined here ./common/env_nowhere.o: In function `env_init': ./common/env_nowhere.c:51: multiple definition of `env_init' ./common/env_flash.o:./common/env_flash.c:237: first defined here make[1]: *** [./common/libcommon.o] Error 1 make[1]: Leaving directory `./common' make: *** [./common/libcommon.o] Error 2 Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE. Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
-
由 Liu Gang 提交于
Rewrite this struct for the support of two ports and two message units registers. Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
-
由 Prabhakar Kushwaha 提交于
Currently "u-boot", the elf file generated via u-boot-nand.lds does not contain required debug information i.e. .debug_{line, info, abbrev, aranges, ranges} into their respective _global_ sections. The original ld script line arch/powerpc/cpu/mpc85xx/start.o KEEP(*(.bootpg)) is not entirely correct because the start.o file is already processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will not process start.o again for bootpg. So Fix u-boot-nand.lds to generate these debug information. Signed-off-by: NAnmol Paralkar <b07584@freescale.com> Signed-off-by: NJohn Russo <John.Russo@freescale.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Shaohui Xie 提交于
Add env in NAND support when boot from NAND. Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Shaohui Xie 提交于
New P2041RDB board will add a NAND chip, so add support for NAND and NAND boot. Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 York Sun 提交于
P1010RDB and p1_pc_rdb_pc has incorrect configuration for CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING. Incorrect setting causes DDR failure in case of SPD absent. Signed-off-by: NYork Sun <yorksun@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Prabhakar Kushwaha 提交于
NAND SPL code never compile the vector table. So no need to setup interrupt vector table for NAND SPL. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Prabhakar Kushwaha 提交于
After relocation of vector table in SDRAM's lower address, IVORs value should be updated with new handler addresses. As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs are updated with 0x100, 0x200,....f00 hard-coded values. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Prabhakar Kushwaha 提交于
For e500 and e500v2 architecturees processor IVPR address should be alinged on 64K boundary. in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be 64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may not point to an exception handler. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Chunhe Lan 提交于
In the p1023rds, when system boots from nor flash, kernel only accesses nor flash and can not access nand flash with BR0/OR0; when system boots from nand flash, kernel only accesses nand flash and can not access nor flash with BR0/OR0. Default device tree nor and nand node should have the following structure: Example: nor_flash: nor@0,0 { #address-cells = <1>; #size-cells = <1>; compatible = "cfi-flash"; reg = <0x0 0x0 0x02000000>; bank-width = <2>; device-width = <1>; status = "okay"; partition@0 { label = "ramdisk"; reg = <0x00000000 0x01c00000>; }; } nand_flash: nand@1,0 { #address-cells = <1>; #size-cells = <1>; compatible = "fsl,p1023-fcm-nand", "fsl,elbc-fcm-nand"; reg = <0x2 0x0 0x00040000>; status = "disabled"; u-boot-nand@0 { /* This location must not be altered */ /* 1MB for u-boot Bootloader Image */ reg = <0x0 0x00100000>; read-only; }; } When booting from nor flash, the status of nor node is enabled and the status of nand node is disabled in the default dts file, so do not do anything. But, when booting from nand flash, need to do some operations: o Disable the NOR node by setting status = "disabled"; o Enable the NAND node by setting status = "okay"; Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
- 24 4月, 2012 4 次提交
-
-
由 Simon Glass 提交于
Now that run_command() handles both parsers, clean up sandbox to use it. This fixes a build error. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NMike Frysinger <vapier@gentoo.org>
-
由 Stephen Warren 提交于
Commit 0a672d49 "arm: Add Prep subcommand support to bootm" re-organized do_bootm_linux for ARM. During the re-organization, the call to fdt_fixup_ethernet() was removed. I assume this was useful, so add it back. Signed-off-by: NStephen Warren <swarren@nvidia.com> Acked-by: NTom Rini <trini@ti.com>
-
由 Stephen Warren 提交于
Commit 0a672d49 "arm: Add Prep subcommand support to bootm" re-organized do_bootm_linux() for ARM. During the re-organization, the code to pass the device tree to the kernel was removed. Add it back. This restores the ability to boot a kernel using device tree. Signed-off-by: NStephen Warren <swarren@nvidia.com> Acked-by: NTom Rini <trini@ti.com> Acked-by: NAllen Martin <amartin@nvidia.com> Tested-by: NAllen Martin <amartin@nvidia.com>
-
由 Timo Ketola 提交于
If one command fails, 'run' command should terminate and not execute any remaining variables. Signed-off-by: NTimo Ketola <timo@exertus.fi> Tested-by: NWolfgang Denk <wd@denx.de> Tested-by: NSimon Glass <sjg@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org>
-
- 22 4月, 2012 1 次提交
-
-
由 Wolfgang Denk 提交于
Also tiny style cleanup to tools/patman/README Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 21 4月, 2012 8 次提交
-
-
由 Stephan Linz 提交于
... after commit "net/miiphy/serial: drop duplicate NAMESIZE define" (sha1:f6add132) was applied. The building of the new LL TEMAC network driver fails with error below: xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize': xilinx_ll_temac.c:301: error: 'NAMESIZE' undeclared (first use in this function) xilinx_ll_temac.c:301: error: (Each undeclared identifier is reported only once xilinx_ll_temac.c:301: error: for each function it appears in.) Signed-off-by: NStephan Linz <linz@li-pro.net> Acked-by: NMike Frysinger <vapier@gentoo.org>
-
由 Simon Glass 提交于
What is this? ============= This tool is a Python script which: - Creates patch directly from your branch - Cleans them up by removing unwanted tags - Inserts a cover letter with change lists - Runs the patches through checkpatch.pl and its own checks - Optionally emails them out to selected people It is intended to automate patch creation and make it a less error-prone process. It is useful for U-Boot and Linux work so far, since it uses the checkpatch.pl script. It is configured almost entirely by tags it finds in your commits. This means that you can work on a number of different branches at once, and keep the settings with each branch rather than having to git format-patch, git send-email, etc. with the correct parameters each time. So for example if you put: in one of your commits, the series will be sent there. See the README file for full details. END Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Jens Scharsig 提交于
Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>
-
由 Dirk Behme 提交于
Fix the warning mmc.c: In function 'mmc_send_cmd': mmc.c:87: warning: assignment from incompatible pointer type in case CONFIG_MMC_TRACE is enabled. Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com> CC: Andy Fleming <afleming@freescale.com> Acked-by: NSimon Glass <sjg@chromium.org> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Jeroen Hofstee 提交于
This is just a patch for the problem reported here: http://lists.denx.de/pipermail/u-boot/2012-February/117580.html originally reported by Igor. "Looks like this is copy paste error from my side,(for port2/3 it should have been bypass for port2/3 rather its port1 set in bypass mode)" I only submit the patch since it is missing in 2012.04-rc3 while the twister board depends on it. Maybe it is already somewhere in the reposistory, but I cannot find it. note: the twister boards still needs an additional `usb reset`, don't know why. U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 21:38:38) AM35XX-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz TAM3517 TWISTER Board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 In: serial Out: serial Err: serial Die ID #746c0000000000000155dc1405011024 Net: DaVinci-EMAC, smc911x-0 Hit any key to stop autoboot: 0 twister => usb start (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found twister => usb reset (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found twister => usb reset (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found twister => usb reset (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Govindraj.R <govindraj.raja <at> ti.com> Acked-by: NTom Rini <trini@ti.com>
-
由 Wolfgang Denk 提交于
Current versions of dtc always print a message like DTC: dts->dtb on file "dt.dtb.tmp" which cannot even be suppressed with "-qqq". To avoid incorrect MAKEALL status, we manually filter out this message. This is a bit complicated, as we have to make sure to set a correct return code. Also, get rid of the temp file: dtc accepts "-" for stdin. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Wolfgang Denk 提交于
Fix: FATAL ERROR: Couldn't open "../arch/arm/dts/tegra20.dtsi": No such file or directory Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Wolfgang Denk 提交于
Fix gcc 4.6 build warnings: onenand_base.c: In function 'onenand_probe': onenand_base.c:2577:6: warning: variable 'maf_id' set but not used [-Wunused-but-set-variable] Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: NLukasz Majewski <l.majewski@samsung.com>
-
- 19 4月, 2012 2 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
git://git.denx.de/u-boot-sh由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-sh: sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT sh: Fix rsk7264 pin setup for on-board ethernet
-
- 18 4月, 2012 2 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT. The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Phil Edworthy 提交于
This sets up the external ethernet IRQ pin. Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 17 4月, 2012 5 次提交
-
-
由 Dirk Behme 提交于
Do the same AXI cache and Qos settings done already in the SabreLite imximage.cfg for the ARM2 board, too. It fixes a display flash issue caused by low priority of the display IDMA channel. Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com> CC: Jason Chen <b02280@freescale.com> CC: Jason Liu <r64343@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <festevam@gmail.com> Acked-by: NJason Liu <r64343@freescale.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
git://git.denx.de/u-boot-arm由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-arm: ARM926EJS: Fix cache.c to comply with checkpatch.pl ARM926EJS: Make asm routines volatile in cache ops MX35: mx35pdk: wrong board revision ARM1136: MX35: Make asm routines volatile in cache ops ARM: add u-boot.imx as target for i.MX SOCs M28: Pull out CONFIG_APBH_DMA so it's always enabled DMA: Split the APBH DMA init into block and channel init imx: Return gpio_set_value in gpio_direction_output imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5) imx: Add GPIO_TO_PORT macro in the mxc_gpio driver imx: Remove unneeded/repititive definitions from imx headers i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC MX31: mx31pdk: drop enable_caches from board file i.MX28: Fix initial stack pointer position mx35: mx35pdk: fix when cache functions are linked mx35: flea3: fix when cache functions are linked ARM: 926ejs: use debug() for misaligned addresses ARM1136: add cache flush and invalidate operations mx6qsabrelite: Fix the serial console port mx6qsabrelite: Add boot switch setting information into the README i.MX6: mx6qsabrelite: add cache commands if cache is enabled i.MX6: implement enable_caches() i.MX6: define CACHELINE_SIZE MX53: DDR: Fix ZQHWCTRL field TZQ_CS mx28evk: Add a README file mx28: Split the README into a common part and a m28 specific part tricorder: Load kernel from ubifs tricorder: Add UBIFS cm-t35: fix Ethernet reset timing hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT BeagleBoard: Remove userbutton command and use gpio command instead OMAP: Move omap1510inn to Unmaintained / Orphaned
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
-
由 Marek Vasut 提交于
We certainly don't want the compiler to reorganise the code for dcache flushing. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: NMike Frysinger <vapier@gentoo.org> Acked-by: NStefano Babic <sbabic@denx.de>
-
- 16 4月, 2012 7 次提交
-
-
由 Stefano Babic 提交于
The board revision is detected accessing to the pmic, that is not available before relocation (I2C). This generates the following error: CPU: Freescale i.MX35 rev 2.0 at 532 MHz. Reset cause: WDOG <reg num> = 7 is invalid. Should be less than 0 Board: MX35 PDK 1.0 The revision number is wrong, as a default value is printed (tested on a mx35pdk Rev. 2.0). Move the output in the board_late_init(), when pmic can be accessed. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Stefano Babic 提交于
As well as pushed for ARM926EJS, we certainly don't want the compiler to reorganise the code for dcache flushing Fix checkpatch warnings as well. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Marek Vasut <marex@denx.de> CC: Albert Aribaud <albert.u.boot@aribaud.net>
-
由 Stefano Babic 提交于
Freescale SOCs require an header to u-boot.bin The patch adds u-boot.imx to the default targets if the imx file is set (IMX_CONFIG). Signed-off-by: NStefano Babic <sbabic@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> CC: Loïc Minier <loic.minier@linaro.org> CC: Mike Frysinger <vapier@gentoo.org> Acked-by: NMike Frysinger <vapier@gentoo.org> Acked-by: NDirk Behme <dirk.behme@de.bosch.com> Tested-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Marek Vasut 提交于
The ABPH DMA is now used also by the SD card. Therefore it has to be enabled even if NAND is disabled. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
-
由 Marek Vasut 提交于
This fixes the issue where mxs_dma_init() was called either twice or never, without introducing any new init hooks. The idea is to allow each and every device using the APBH DMA block to configure and request only the channels it uses, instead of making it call init for all the channels as is now. The common DMA block init part, which only configures the block, is then called from CPUs arch_cpu_init() call. NOTE: This patch depends on: http://patchwork.ozlabs.org/patch/150957/Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Vikram Narayanan 提交于
Return gpio_set_value in gpio_direction_output. Earlier it returned 0 and ignored gpio_set_value's return value. Signed-off-by: NVikram Narayanan <vikram186@gmail.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Vikram Narayanan 提交于
Use the defined GPIO_TO_PORT macro. Remove gpio >> 5 references. Signed-off-by: NVikram Narayanan <vikram186@gmail.com> Acked-by: NStefano Babic <sbabic@denx.de>
-