arm64: zynqmp: Add support for zcu104 customer board

Xilinx zcu104 is another customer board. It is sort of zcu102 clone with
some differences.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

arch/arm/dts/Makefile

@@ -152,6 +152,8 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \
 	zynqmp-zcu102-revA.dtb			\
 	zynqmp-zcu102-revB.dtb			\
 	zynqmp-zcu102-rev1.0.dtb		\
+	zynqmp-zcu104-revA.dtb			\
+	zynqmp-zcu104-revC.dtb			\
 	zynqmp-zc1232-revA.dtb			\
 	zynqmp-zc1254-revA.dtb			\
 	zynqmp-zc1275-revA.dtb			\

arch/arm/dts/zynqmp-zcu104-revA.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU104
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU104 RevA";
+	compatible = "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		gpio0 = &gpio;
+		i2c0 = &i2c1;
+		mmc0 = &sdhci1;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+	};
+};
+
+&gpio {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Another connection to this bus via PL i2c via PCA9306 - u45 */
+	i2c-mux@74 { /* u34 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u23 */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
+				compatible = "idt,8t49n287";
+				reg = <0x6c>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x43>;
+			};
+			irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x4d>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			tca6416_u97: gpio@21 {
+				compatible = "ti,tca6416";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				/*
+				 * IRQ not connected
+				 * Lines:
+				 * 0 - IRPS5401_ALERT_B
+				 * 1 - HDMI_8T49N241_INT_ALM
+				 * 2 - MAX6643_OT_B
+				 * 3 - MAX6643_FANFAIL_B
+				 * 5 - IIC_MUX_RESET_B
+				 * 6 - GEM3_EXP_RESET_B
+				 * 7 - FMC_LPC_PRSNT_M2C_B
+				 * 4, 10 - 17 - not connected
+				 */
+			};
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+		/* 3, 6 not connected */
+	};
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80"; /* n25q512a 128MiB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@qspi-fsbl-uboot { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@qspi-linux { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@qspi-device-tree { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@qspi-rootfs { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	no-1-8-v;
+	xlnx,mio_bank = <1>;
+	disable-wp;
+};
+
+&serdes {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+	phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+	maximum-speed = "super-speed";
+};
+
+&watchdog0 {
+	status = "okay";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};

arch/arm/dts/zynqmp-zcu104-revC.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU104
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU104 RevC";
+	compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		gpio0 = &gpio;
+		i2c0 = &i2c1;
+		mmc0 = &sdhci1;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&dcc {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+	};
+};
+
+&gpio {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tca6416_u97: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		/*
+		 * IRQ not connected
+		 * Lines:
+		 * 0 - IRPS5401_ALERT_B
+		 * 1 - HDMI_8T49N241_INT_ALM
+		 * 2 - MAX6643_OT_B
+		 * 3 - MAX6643_FANFAIL_B
+		 * 5 - IIC_MUX_RESET_B
+		 * 6 - GEM3_EXP_RESET_B
+		 * 7 - FMC_LPC_PRSNT_M2C_B
+		 * 4, 10 - 17 - not connected
+		 */
+	};
+
+	/* Another connection to this bus via PL i2c via PCA9306 - u45 */
+	i2c-mux@74 { /* u34 */
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u23 */
+				compatible = "atmel,24c08";
+				reg = <0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
+				compatible = "idt,8t49n287";
+				reg = <0x6c>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x43>;
+			};
+			irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x4d>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+		/* 3, 6 not connected */
+	};
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80"; /* n25q512a 128MiB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+		partition@qspi-fsbl-uboot { /* for testing purpose */
+			label = "qspi-fsbl-uboot";
+			reg = <0x0 0x100000>;
+		};
+		partition@qspi-linux { /* for testing purpose */
+			label = "qspi-linux";
+			reg = <0x100000 0x500000>;
+		};
+		partition@qspi-device-tree { /* for testing purpose */
+			label = "qspi-device-tree";
+			reg = <0x600000 0x20000>;
+		};
+		partition@qspi-rootfs { /* for testing purpose */
+			label = "qspi-rootfs";
+			reg = <0x620000 0x5E0000>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	no-1-8-v;
+	xlnx,mio_bank = <1>;
+	disable-wp;
+};
+
+&serdes {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+	phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+	maximum-speed = "super-speed";
+};
+
+&watchdog0 {
+	status = "okay";
+};
+
+&xilinx_ams {
+	status = "okay";
+};
+
+&ams_ps {
+	status = "okay";
+};
+
+&ams_pl {
+	status = "okay";
+};

board/xilinx/zynqmp/zynqmp-zcu104-revC

+zynqmp-zcu104-revA
\ No newline at end of file

configs/xilinx_zynqmp_zcu104_revA_defconfig

+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zcu104"
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_SYS_TEXT_BASE=0x8000000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_SPL=y
+CONFIG_IDENT_STRING=" Xilinx ZynqMP ZCU104 revA"
+CONFIG_ZYNQMP_USB=y
+CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu104-revA"
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_RAM_SUPPORT=y
+CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
+CONFIG_SYS_PROMPT="ZynqMP> "
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_SPL_ISO_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_CLK_ZYNQMP=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQMPPL=y
+CONFIG_DM_GPIO=y
+CONFIG_CMD_PCA953X=y
+CONFIG_SYS_I2C_ZYNQ=y
+CONFIG_ZYNQ_I2C1=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SF_DUAL_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_NATSEMI=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_TI=y
+CONFIG_PHY_VITESSE=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xff000000
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_XHCI_ZYNQMP=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GADGET=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y

configs/xilinx_zynqmp_zcu104_revC_defconfig

+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zcu104"
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_SYS_TEXT_BASE=0x8000000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_SPL=y
+CONFIG_IDENT_STRING=" Xilinx ZynqMP ZCU104 revC"
+CONFIG_ZYNQMP_USB=y
+CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu104-revC"
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_RAM_SUPPORT=y
+CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
+CONFIG_SYS_PROMPT="ZynqMP> "
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FPGA_LOADBP=y
+CONFIG_CMD_FPGA_LOADP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_SPL_ISO_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_CLK_ZYNQMP=y
+CONFIG_DFU_RAM=y
+CONFIG_FPGA_XILINX=y
+CONFIG_FPGA_ZYNQMPPL=y
+CONFIG_DM_GPIO=y
+CONFIG_CMD_PCA953X=y
+CONFIG_SYS_I2C_ZYNQ=y
+CONFIG_ZYNQ_I2C1=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ZYNQ=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SF_DUAL_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_NATSEMI=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_TI=y
+CONFIG_PHY_VITESSE=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_ZYNQ_GEM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_DEBUG_UART_ZYNQ=y
+CONFIG_DEBUG_UART_BASE=0xff000000
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ZYNQ_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_XHCI_ZYNQMP=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GADGET=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y

include/configs/xilinx_zynqmp_zcu104.h

+/*
+ * Configuration for Xilinx ZynqMP zcu104
+ *
+ * (C) Copyright 2017 Xilinx, Inc.
+ * Michal Simek <michal.simek@xilinx.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_ZYNQMP_ZCU104_H
+#define __CONFIG_ZYNQMP_ZCU104_H
+
+#define CONFIG_ZYNQ_SDHCI1
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_NUM_I2C_BUSES	9
+#define CONFIG_SYS_I2C_BUSES	{ \
+				{0, {I2C_NULL_HOP} }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 0} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 1} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 2} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 3} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 4} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 5} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 6} } }, \
+				{0, {{I2C_MUX_PCA9548, 0x74, 7} } }, \
+				}
+
+#define CONFIG_PCA953X
+
+#define CONFIG_ZYNQMP_XHCI_LIST {ZYNQMP_USB0_XHCI_BASEADDR}
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+#include <configs/xilinx_zynqmp.h>
+
+#endif /* __CONFIG_ZYNQMP_ZCU104_H */