Convert CONFIG_CONS_INDEX et al to Kconfig

This converts the following to Kconfig:
   CONFIG_CONS_INDEX
   CONFIG_DEBUG_UART_CLOCK
   CONFIG_FSL_TZPC_BP147
   CONFIG_GENERIC_ATMEL_MCI
   CONFIG_IDENT_STRING
   CONFIG_LIBATA
   CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
   CONFIG_LPC32XX_GPIO
   CONFIG_MP
   CONFIG_MPC8XXX_GPIO
   CONFIG_MTD_PARTITIONS
   CONFIG_MVGBE
   CONFIG_MXC_GPIO
   CONFIG_NR_DRAM_BANKS
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_PREBOOT
   CONFIG_ROCKCHIP_SERIAL
   CONFIG_RTC_ENABLE_32KHZ_OUTPUT
   CONFIG_RTC_MV
   CONFIG_SCSI_AHCI
   CONFIG_SF_DEFAULT_BUS
   CONFIG_SF_DEFAULT_CS
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SOFT_SPI
   CONFIG_SPI_FLASH_EON
   CONFIG_SPI_FLASH_MACRONIX
   CONFIG_SPI_FLASH_MTD
   CONFIG_SPI_FLASH_SPANSION
   CONFIG_SPI_FLASH_SST
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_SYS_ARCH_TIMER
   CONFIG_SYS_BOARD
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
   CONFIG_SYS_DCACHE_OFF
   CONFIG_SYS_FDT_SAVE_ADDRESS
   CONFIG_SYS_FLASH_CFI
   CONFIG_SYS_FSL_ERRATUM_ESDHC135
   CONFIG_SYS_HAS_SERDES
   CONFIG_SYS_L2CACHE_OFF
   CONFIG_SYS_LITTLE_ENDIAN
   CONFIG_SYS_LOAD_ADDR
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
   CONFIG_SYS_NS16550
   CONFIG_SYS_PLLFIN
   CONFIG_SYS_SPI_U_BOOT_OFFS
   CONFIG_TIMER_SYS_TICK_CH
   CONFIG_USB_EHCI_FSL
   CONFIG_U_QE
   CONFIG_VERSION_VARIABLE
Signed-off-by: NTom Rini <trini@konsulko.com>

README

@@ -565,11 +565,6 @@ The following options need to be configured:
 		boards with QUICC Engines require OF_QE to set UCC MAC
 		addresses
 
-		CONFIG_OF_BOARD_SETUP
-
-		Board code has addition modification that it wants to make
-		to the flat device tree before handing it off to the kernel
-
 		CONFIG_OF_SYSTEM_SETUP
 
 		Other code has addition modification that it wants to make
@@ -596,9 +591,6 @@ The following options need to be configured:
 		Note: If a "bootargs" environment is defined, it will override
 		the defaults discussed just above.
 
-- Cache Configuration:
-		CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
-
 - Cache Configuration for ARM:
 		CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
 				      controller
@@ -1520,16 +1512,6 @@ The following options need to be configured:
 		SPI EEPROM, also an instance works with Crystal A/D and
 		D/As on the SACSng board)
 
-		CONFIG_SOFT_SPI
-
-		Enables a software (bit-bang) SPI driver rather than
-		using hardware support. This is a general purpose
-		driver that only requires three general I/O port pins
-		(two outputs, one input) to function. If this is
-		defined, the board configuration must define several
-		SPI configuration items (port pins to use, etc). For
-		an example, see include/configs/sacsng.h.
-
 		CONFIG_SYS_SPI_MXC_WAIT
 		Timeout for waiting until spi transfer completed.
 		default: (CONFIG_SYS_HZ/100)     /* 10 ms */
@@ -1595,13 +1577,6 @@ The following options need to be configured:
 		Time to wait after FPGA configuration. The default is
 		200 ms.
 
-- Configuration Management:
-
-		CONFIG_IDENT_STRING
-
-		If defined, this string will be added to the U-Boot
-		version information (U_BOOT_VERSION)
-
 - Vendor Parameter Protection:
 
 		U-Boot considers the values of the environment
@@ -1922,10 +1897,6 @@ The following options need to be configured:
 		CONFIG_SPL_INIT_MINIMAL
 		Arch init code should be built for a very small image
 
-		CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
-		Partition on the MMC to load U-Boot from when the MMC is being
-		used in raw mode
-
 		CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
 		Sector to load kernel uImage from when MMC is being
 		used in raw mode (for Falcon mode)

arch/arm/cpu/armv8/fsl-layerscape/Kconfig

@@ -41,6 +41,7 @@ config ARCH_LS1028A
 	select SYS_FSL_SEC_COMPAT_5
 	select SYS_FSL_SEC_LE
 	select FSL_TZASC_1
+	select FSL_TZPC_BP147
 	select ARCH_EARLY_INIT_R
 	select BOARD_EARLY_INIT_F
 	select SYS_I2C_MXC
@@ -241,6 +242,7 @@ config ARCH_LX2162A
 	select FSL_DDR_INTERACTIVE
 	select FSL_LAYERSCAPE
 	select FSL_LSCH3
+	select FSL_TZPC_BP147
 	select GICV3
 	select NXP_LSCH3_2
 	select SYS_HAS_SERDES
@@ -277,6 +279,7 @@ config ARCH_LX2160A
 	select FSL_DDR_INTERACTIVE
 	select FSL_LAYERSCAPE
 	select FSL_LSCH3
+	select FSL_TZPC_BP147
 	select GICV3
 	select HAS_FSL_XHCI_USB if USB_HOST
 	select NXP_LSCH3_2

arch/arm/include/asm/arch-fsl-layerscape/config.h

@@ -234,7 +234,6 @@
 #elif defined(CONFIG_ARCH_LS1028A)
 #define CONFIG_SYS_FSL_NUM_CC_PLLS		3
 #define CONFIG_SYS_FSL_CLUSTER_CLOCKS		{ 1, 1 }
-#define CONFIG_FSL_TZPC_BP147
 #define CONFIG_FSL_TZASC_400
 
 /* TZ Protection Controller Definitions */

arch/arm/mach-apple/Kconfig

@@ -15,4 +15,7 @@ config SYS_MALLOC_LEN
 config SYS_MALLOC_F_LEN
 	default 0x4000
 
+config LNX_KRNL_IMG_TEXT_OFFSET_BASE
+	default SYS_TEXT_BASE
+
 endif

arch/arm/mach-imx/imxrt/Kconfig

@@ -2,6 +2,7 @@ if ARCH_IMXRT
 
 config IMXRT
 	bool
+	select SYS_FSL_ERRATUM_ESDHC135
 
 config IMXRT1020
 	bool

arch/arm/mach-nexell/Kconfig

@@ -33,6 +33,12 @@ config TARGET_NANOPI2
 
 endchoice
 
+config SYS_PLLFIN
+	int
+
+config TIMER_SYS_TICK_CH
+	int
+
 config SYS_BOARD
 	default "nanopi2"
 
@@ -45,13 +51,13 @@ config SYS_SOC
 config SYS_CONFIG_NAME
 	default "s5p4418_nanopi2"
 
-endmenu
-
 config SYS_PLLFIN
-	int
+	default 24000000
 
 config TIMER_SYS_TICK_CH
-	int
+	default 0
+
+endmenu
 
 source "board/friendlyarm/Kconfig"
 

arch/powerpc/cpu/mpc85xx/Kconfig

@@ -354,6 +354,7 @@ config ARCH_P1010
 	bool
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_5
+	select SYS_HAS_SERDES
 	select SYS_FSL_ERRATUM_A004477
 	select SYS_FSL_ERRATUM_A004508
 	select SYS_FSL_ERRATUM_A005125
@@ -1001,6 +1002,9 @@ config SYS_FSL_ERRATUM_SRIO_A004034
 config SYS_FSL_ERRATUM_USB14
 	bool
 
+config SYS_HAS_SERDES
+	bool
+
 config SYS_P4080_ERRATUM_CPU22
 	bool
 

board/siemens/capricorn/MAINTAINERS

@@ -5,7 +5,6 @@ F:	board/siemens/capricorn/
 F:	include/configs/capricorn-common.h
 F:	include/configs/deneb.h
 F:	include/configs/giedi.h
-F:	include/configs/siemens-ccp-common.h
 F:	include/configs/siemens-env-common.h
 F:	configs/deneb_defconfig
 F:	configs/giedi_defconfig

board/xen/xenguest_arm64/Kconfig

@@ -9,4 +9,7 @@ config SYS_VENDOR
 config SYS_CONFIG_NAME
 	default "xenguest_arm64"
 
+config LNX_KRNL_IMG_TEXT_OFFSET_BASE
+	default SYS_LOAD_ADDR
+
 endif

configs/MPC837XERDB_defconfig

@@ -198,3 +198,4 @@ CONFIG_TSEC_ENET=y
 CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PA_36BIT_NAND_defconfig

@@ -96,4 +96,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PA_36BIT_NOR_defconfig

@@ -76,4 +76,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PA_36BIT_SDCARD_defconfig

@@ -88,4 +88,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig

@@ -90,4 +90,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PA_NAND_defconfig

@@ -95,3 +95,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PA_NOR_defconfig

@@ -75,3 +75,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PA_SDCARD_defconfig

@@ -87,3 +87,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PA_SPIFLASH_defconfig

@@ -89,3 +89,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PB_36BIT_NAND_defconfig

@@ -99,4 +99,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PB_36BIT_NOR_defconfig

@@ -78,4 +78,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PB_36BIT_SDCARD_defconfig

@@ -90,4 +90,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig

@@ -92,4 +92,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_ADDR_MAP=y

configs/P1010RDB-PB_NAND_defconfig

@@ -98,3 +98,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PB_NOR_defconfig

@@ -77,3 +77,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PB_SDCARD_defconfig

@@ -89,3 +89,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1010RDB-PB_SPIFLASH_defconfig

@@ -91,3 +91,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P1020RDB-PC_36BIT_NAND_defconfig

@@ -110,5 +110,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P1020RDB-PC_36BIT_SDCARD_defconfig

@@ -99,5 +99,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig

@@ -101,5 +101,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P1020RDB-PC_36BIT_defconfig

@@ -88,5 +88,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P1020RDB-PC_NAND_defconfig

@@ -109,4 +109,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PC_SDCARD_defconfig

@@ -98,4 +98,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PC_SPIFLASH_defconfig

@@ -100,4 +100,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PC_defconfig

@@ -87,4 +87,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PD_NAND_defconfig

@@ -113,4 +113,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PD_SDCARD_defconfig

@@ -102,4 +102,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PD_SPIFLASH_defconfig

@@ -104,4 +104,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P1020RDB-PD_defconfig

@@ -91,4 +91,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P2020RDB-PC_36BIT_NAND_defconfig

@@ -115,5 +115,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P2020RDB-PC_36BIT_SDCARD_defconfig

@@ -104,5 +104,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig

@@ -106,5 +106,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P2020RDB-PC_36BIT_defconfig

@@ -93,5 +93,6 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y

configs/P2020RDB-PC_NAND_defconfig

@@ -114,4 +114,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P2020RDB-PC_SDCARD_defconfig

@@ -103,3 +103,4 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y

configs/P2020RDB-PC_SPIFLASH_defconfig

@@ -105,4 +105,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P2020RDB-PC_defconfig

@@ -92,4 +92,5 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y

configs/P2041RDB_NAND_defconfig

@@ -82,6 +82,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P2041RDB_SDCARD_defconfig

@@ -78,6 +78,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P2041RDB_SPIFLASH_defconfig

@@ -79,6 +79,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P2041RDB_defconfig

@@ -74,6 +74,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P3041DS_NAND_defconfig

@@ -84,6 +84,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P3041DS_SDCARD_defconfig

@@ -80,6 +80,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P3041DS_SPIFLASH_defconfig

@@ -81,6 +81,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P3041DS_defconfig

@@ -76,6 +76,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P4080DS_SDCARD_defconfig

@@ -79,6 +79,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P4080DS_SPIFLASH_defconfig

@@ -80,6 +80,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P4080DS_defconfig

@@ -75,6 +75,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P5040DS_NAND_defconfig

@@ -85,6 +85,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P5040DS_SDCARD_defconfig

@@ -80,6 +80,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P5040DS_SPIFLASH_defconfig

@@ -81,6 +81,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/P5040DS_defconfig

@@ -76,6 +76,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/SBx81LIFKW_defconfig

@@ -44,16 +44,17 @@ CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_PHYLIB=y
 CONFIG_MV88E61XX_SWITCH=y
 CONFIG_MV88E61XX_CPU_PORT=10
 CONFIG_MV88E61XX_PHY_PORTS=0x003
 CONFIG_MV88E61XX_FIXED_PORTS=0x300
 CONFIG_PHY_FIXED=y
 CONFIG_DM_ETH=y
+CONFIG_MVGBE=y
 CONFIG_MII=y
 CONFIG_DM_RTC=y
 CONFIG_RTC_MV=y
+CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_KIRKWOOD_SPI=y

configs/SBx81LIFXCAT_defconfig

@@ -48,14 +48,15 @@ CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_PHYLIB=y
 CONFIG_MV88E61XX_SWITCH=y
 CONFIG_MV88E61XX_CPU_PORT=10
 CONFIG_MV88E61XX_PHY_PORTS=0x003
 CONFIG_MV88E61XX_FIXED_PORTS=0x300
 CONFIG_PHY_FIXED=y
 CONFIG_DM_ETH=y
+CONFIG_MVGBE=y
 CONFIG_MII=y
+CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_KIRKWOOD_SPI=y

configs/T1024RDB_NAND_defconfig

@@ -104,6 +104,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1024RDB_SDCARD_defconfig

@@ -101,6 +101,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1024RDB_SPIFLASH_defconfig

@@ -103,6 +103,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1024RDB_defconfig

@@ -86,6 +86,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1042D4RDB_NAND_defconfig

@@ -92,6 +92,7 @@ CONFIG_FMAN_ENET=y
 CONFIG_SYS_FMAN_FW_ADDR=0x280000
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
+CONFIG_U_QE=y
 CONFIG_SYS_QE_FW_ADDR=0x380000
 CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
 CONFIG_DM_RTC=y
@@ -100,6 +101,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1042D4RDB_SDCARD_defconfig

@@ -88,6 +88,7 @@ CONFIG_FMAN_ENET=y
 CONFIG_SYS_FMAN_FW_ADDR=0x10400
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
+CONFIG_U_QE=y
 CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
 CONFIG_DM_RTC=y
 CONFIG_SYS_NS16550=y
@@ -95,6 +96,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1042D4RDB_SPIFLASH_defconfig

@@ -90,6 +90,7 @@ CONFIG_FMAN_ENET=y
 CONFIG_SYS_FMAN_FW_ADDR=0x110000
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
+CONFIG_U_QE=y
 CONFIG_SYS_QE_FW_ADDR=0x130000
 CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
 CONFIG_DM_RTC=y
@@ -98,6 +99,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T1042D4RDB_defconfig

@@ -73,6 +73,7 @@ CONFIG_FMAN_ENET=y
 CONFIG_SYS_FMAN_FW_ADDR=0xEFF00000
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
+CONFIG_U_QE=y
 CONFIG_SYS_QE_FW_ADDR=0xEFF10000
 CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
 CONFIG_DM_RTC=y
@@ -81,6 +82,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080QDS_NAND_defconfig

@@ -98,6 +98,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080QDS_SDCARD_defconfig

@@ -94,6 +94,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080QDS_SECURE_BOOT_defconfig

@@ -78,6 +78,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080QDS_SPIFLASH_defconfig

@@ -96,6 +96,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080QDS_SRIO_PCIE_BOOT_defconfig

@@ -71,6 +71,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080QDS_defconfig

@@ -79,6 +79,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_NAND_defconfig

@@ -106,6 +106,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_SDCARD_defconfig

@@ -102,6 +102,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_SPIFLASH_defconfig

@@ -104,6 +104,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_defconfig

@@ -85,6 +85,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_revD_NAND_defconfig

@@ -108,6 +108,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_revD_SDCARD_defconfig

@@ -104,6 +104,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_revD_SPIFLASH_defconfig

@@ -106,6 +106,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T2080RDB_revD_defconfig

@@ -88,6 +88,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T4240RDB_SDCARD_defconfig

@@ -88,6 +88,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/T4240RDB_defconfig

@@ -73,6 +73,7 @@ CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_FSL_ESPI=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_FSL=y
 CONFIG_USB_STORAGE=y
 CONFIG_ADDR_MAP=y
 CONFIG_SYS_NUM_ADDR_MAP=64

configs/a3y17lte_defconfig

@@ -9,6 +9,8 @@ CONFIG_NR_DRAM_BANKS=8
 CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte"
 CONFIG_SYS_LOAD_ADDR=0x40001000
 CONFIG_FIT=y
+CONFIG_USE_PREBOOT=y
+CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_GPIO=y

configs/a5y17lte_defconfig

@@ -9,6 +9,8 @@ CONFIG_NR_DRAM_BANKS=12
 CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte"
 CONFIG_SYS_LOAD_ADDR=0x40001000
 CONFIG_FIT=y
+CONFIG_USE_PREBOOT=y
+CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_GPIO=y

configs/a7y17lte_defconfig

@@ -9,6 +9,8 @@ CONFIG_NR_DRAM_BANKS=12
 CONFIG_DEFAULT_DEVICE_TREE="exynos78x0-axy17lte"
 CONFIG_SYS_LOAD_ADDR=0x40001000
 CONFIG_FIT=y
+CONFIG_USE_PREBOOT=y
+CONFIG_PREBOOT="echo Read pressed buttons status;KEY_VOLUMEUP=gpa20;KEY_HOME=gpa17;KEY_VOLUMEDOWN=gpa21;KEY_POWER=gpa00;PRESSED=0;RELEASED=1;if gpio input $KEY_VOLUMEUP; then setenv VOLUME_UP $PRESSED; else setenv VOLUME_UP $RELEASED; fi;if gpio input $KEY_VOLUMEDOWN; then setenv VOLUME_DOWN $PRESSED; else setenv VOLUME_DOWN $RELEASED; fi;if gpio input $KEY_HOME; then setenv HOME $PRESSED; else setenv HOME $RELEASED; fi;if gpio input $KEY_POWER; then setenv POWER $PRESSED; else setenv POWER $RELEASED; fi;"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_GPIO=y

configs/apalis-tk1_defconfig

 CONFIG_ARM=y
+CONFIG_SYS_L2CACHE_OFF=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_SYS_TEXT_BASE=0x80110000
 CONFIG_SYS_MALLOC_F_LEN=0x2000

configs/apalis_imx6_defconfig

@@ -27,6 +27,7 @@ CONFIG_AHCI=y
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_FIT=y
 CONFIG_BOOTDELAY=1
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_BOARD_EARLY_INIT_F=y

configs/apalis_t30_defconfig

 CONFIG_ARM=y
+CONFIG_SYS_L2CACHE_OFF=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_SYS_TEXT_BASE=0x80110000
 CONFIG_SYS_MALLOC_F_LEN=0x2000

configs/bcm7260_defconfig

@@ -35,4 +35,5 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_BCMSTB=y
 CONFIG_MTD=y
+CONFIG_SYS_NS16550=y
 # CONFIG_EFI_LOADER is not set

configs/bcm7445_defconfig

@@ -37,6 +37,9 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_BCMSTB=y
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_BCMSTB_SPI=y

configs/beaver_defconfig

 CONFIG_ARM=y
+CONFIG_SYS_L2CACHE_OFF=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_SYS_TEXT_BASE=0x80110000
 CONFIG_SYS_MALLOC_LEN=0x2500000

configs/bitmain_antminer_s9_defconfig

@@ -3,6 +3,7 @@ CONFIG_SYS_VENDOR="bitmain"
 CONFIG_SYS_BOARD="antminer_s9"
 CONFIG_SYS_CONFIG_NAME="bitmain_antminer_s9"
 CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_SYS_L2CACHE_OFF=y
 CONFIG_ARCH_ZYNQ=y
 CONFIG_SYS_TEXT_BASE=0x4000000
 CONFIG_ENV_OFFSET=0x300000

configs/cardhu_defconfig

 CONFIG_ARM=y
+CONFIG_SYS_L2CACHE_OFF=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_SYS_TEXT_BASE=0x80110000
 CONFIG_NR_DRAM_BANKS=2

configs/cei-tk1-som_defconfig

 CONFIG_ARM=y
+CONFIG_SYS_L2CACHE_OFF=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_SYS_TEXT_BASE=0x80110000
 CONFIG_SYS_MALLOC_LEN=0x2500000

configs/cgtqmx8_defconfig

@@ -21,6 +21,7 @@ CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y
 CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=3
 CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else booti ${loadaddr} - ${fdt_addr}; fi"
@@ -28,6 +29,8 @@ CONFIG_LOG=y
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x800
 CONFIG_SYS_MMCSD_FS_BOOT_PARTITION=0
 CONFIG_SPL_POWER_DOMAIN=y
 CONFIG_SPL_WATCHDOG=y