sata: Rename SATA_SUPPORT to SATA

Rename this options so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: NSimon Glass <sjg@chromium.org>

arch/arm/mach-mvebu/Kconfig

@@ -298,7 +298,7 @@ config MVEBU_SPL_BOOT_DEVICE_MMC
 
 config MVEBU_SPL_BOOT_DEVICE_SATA
 	bool "SATA"
-	imply SPL_SATA_SUPPORT
+	imply SPL_SATA
 	imply SPL_LIBDISK_SUPPORT
 	select SPL_BOOTROM_SUPPORT
 

arch/arm/mach-mvebu/spl.c

@@ -18,7 +18,7 @@
 #include <asm/arch/soc.h>
 
 #if defined(CONFIG_SPL_SPI_FLASH_SUPPORT) || defined(CONFIG_SPL_MMC) || \
-	defined(CONFIG_SPL_SATA_SUPPORT)
+	defined(CONFIG_SPL_SATA)
 
 /*
  * When loading U-Boot via SPL from SPI NOR, CONFIG_SYS_SPI_U_BOOT_OFFS must
@@ -57,7 +57,7 @@
  * stored at sector 1. Therefore CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR must be
  * set to 1. Otherwise U-Boot SPL would not be able to load U-Boot proper.
  */
-#ifdef CONFIG_SPL_SATA_SUPPORT
+#ifdef CONFIG_SPL_SATA
 #if !defined(CONFIG_SPL_SATA_RAW_U_BOOT_USE_SECTOR) || !defined(CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR) || CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR != 1
 #error CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR must be set to 1
 #endif
@@ -122,7 +122,7 @@ int spl_parse_board_header(struct spl_image_info *spl_image,
 #ifdef CONFIG_SPL_SPI_FLASH_SUPPORT
 	     mhdr->blockid != IBR_HDR_SPI_ID &&
 #endif
-#ifdef CONFIG_SPL_SATA_SUPPORT
+#ifdef CONFIG_SPL_SATA
 	     mhdr->blockid != IBR_HDR_SATA_ID &&
 #endif
 #ifdef CONFIG_SPL_MMC
@@ -136,7 +136,7 @@ int spl_parse_board_header(struct spl_image_info *spl_image,
 
 	spl_image->offset = mhdr->srcaddr;
 
-#ifdef CONFIG_SPL_SATA_SUPPORT
+#ifdef CONFIG_SPL_SATA
 	/*
 	 * For SATA srcaddr is specified in number of sectors.
 	 * The main header is must be stored at sector number 1.
@@ -266,7 +266,7 @@ u32 spl_boot_device(void)
 	case BOOT_DEVICE_MMC1:
 		return BOOT_DEVICE_MMC1;
 #endif
-#ifdef CONFIG_SPL_SATA_SUPPORT
+#ifdef CONFIG_SPL_SATA
 	case BOOT_FROM_SATA:
 		return BOOT_FROM_SATA;
 #endif

arch/arm/mach-zynqmp/spl.c

@@ -100,7 +100,7 @@ u32 spl_boot_device(void)
 	case USB_MODE:
 		return BOOT_DEVICE_DFU;
 #endif
-#ifdef CONFIG_SPL_SATA_SUPPORT
+#ifdef CONFIG_SPL_SATA
 	case SW_SATA_MODE:
 		return BOOT_DEVICE_SATA;
 #endif

arch/powerpc/cpu/mpc83xx/Kconfig

@@ -119,7 +119,7 @@ config MPC83XX_PCIE2_SUPPORT
 config MPC83XX_SDHC_SUPPORT
 	bool
 
-config MPC83XX_SATA_SUPPORT
+config MPC83XX_SATA
 	bool
 
 config MPC83XX_SECOND_I2C
@@ -198,7 +198,7 @@ config ARCH_MPC837X
 	select MPC83XX_PCIE1_SUPPORT
 	select MPC83XX_PCIE2_SUPPORT
 	select MPC83XX_SDHC_SUPPORT
-	select MPC83XX_SATA_SUPPORT
+	select MPC83XX_SATA
 	select MPC83XX_LDP_PIN
 	select MPC83XX_SECOND_I2C
 	select SYS_CACHE_SHIFT_5

common/spl/Kconfig

@@ -196,7 +196,7 @@ config SPL_BOOTCOUNT_LIMIT
 
 config SPL_RAW_IMAGE_SUPPORT
 	bool "Support SPL loading and booting of RAW images"
-	default n if (ARCH_MX6 && (SPL_MMC || SPL_SATA_SUPPORT))
+	default n if (ARCH_MX6 && (SPL_MMC || SPL_SATA))
 	default y if !TI_SECURE_DEVICE
 	help
 	  SPL will support loading and booting a RAW image when this option
@@ -1076,7 +1076,7 @@ config SPL_RTC
 	  needed. This enables the drivers in drivers/rtc as part of an SPL
 	  build.
 
-config SPL_SATA_SUPPORT
+config SPL_SATA
 	bool "Support loading from SATA"
 	help
 	  Enable support for SATA (Serial AT attachment) in SPL. This allows
@@ -1088,7 +1088,7 @@ config SPL_SATA_SUPPORT
 
 config SPL_SATA_RAW_U_BOOT_USE_SECTOR
 	bool "SATA raw mode: by sector"
-	depends on SPL_SATA_SUPPORT
+	depends on SPL_SATA
 	default y if ARCH_MVEBU
 	help
 	  Use sector number for specifying U-Boot location on SATA disk in

common/spl/Makefile

@@ -27,7 +27,7 @@ obj-$(CONFIG_$(SPL_TPL_)OPENSBI) += spl_opensbi.o
 obj-$(CONFIG_$(SPL_TPL_)USB_STORAGE) += spl_usb.o
 obj-$(CONFIG_$(SPL_TPL_)FS_FAT) += spl_fat.o
 obj-$(CONFIG_$(SPL_TPL_)FS_EXT4) += spl_ext.o
-obj-$(CONFIG_$(SPL_TPL_)SATA_SUPPORT) += spl_sata.o
+obj-$(CONFIG_$(SPL_TPL_)SATA) += spl_sata.o
 obj-$(CONFIG_$(SPL_TPL_)DFU) += spl_dfu.o
 obj-$(CONFIG_$(SPL_TPL_)SPI_LOAD) += spl_spi.o
 obj-$(CONFIG_$(SPL_TPL_)RAM_SUPPORT) += spl_ram.o

drivers/Makefile

@@ -60,7 +60,7 @@ obj-$(CONFIG_SPL_USB_GADGET) += usb/gadget/udc/
 obj-$(CONFIG_SPL_WATCHDOG) += watchdog/
 obj-$(CONFIG_SPL_USB_HOST) += usb/host/
 obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/
-obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/
+obj-$(CONFIG_SPL_SATA) += ata/ scsi/
 obj-$(CONFIG_HAVE_BLOCK_DEVICE) += block/
 obj-$(CONFIG_SPL_THERMAL) += thermal/
 

drivers/scsi/Makefile

@@ -9,7 +9,7 @@ obj-$(CONFIG_SCSI) += scsi.o
 endif
 
 ifdef CONFIG_SPL_BUILD
-ifdef CONFIG_SPL_SATA_SUPPORT
+ifdef CONFIG_SPL_SATA
 obj-$(CONFIG_DM_SCSI) += scsi-uclass.o
 obj-$(CONFIG_SCSI) += scsi.o
 endif

include/configs/imx6_spl.h

@@ -59,7 +59,7 @@
 #endif
 
 /* SATA support */
-#if defined(CONFIG_SPL_SATA_SUPPORT)
+#if defined(CONFIG_SPL_SATA)
 #define CONFIG_SPL_SATA_BOOT_DEVICE		0
 #define CONFIG_SYS_SATA_FAT_BOOT_PARTITION	1
 #endif