Get rid of bogus CONFIG_SYS_BUS_HZ and CONFIG_SYS_CONFIG_BUS_CLK definitions

CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality.  Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>

arch/powerpc/cpu/74xx_7xx/cpu.c

@@ -277,19 +277,17 @@ do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 /*
  * For the 7400 the TB clock runs at 1/4 the cpu bus speed.
  */
-#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SYS_CONFIG_BUS_CLK)
+#if defined(CONFIG_AMIGAONEG3SE) || !defined(CONFIG_SYS_BUS_CLK)
+#define	CONFIG_SYS_BUS_CLK gd->bus_clk
+#endif
+
 unsigned long get_tbclk(void)
 {
-	return (gd->bus_clk / 4);
+	return CONFIG_SYS_BUS_CLK / 4;
 }
-#else	/* ! CONFIG_AMIGAONEG3SE and !CONFIG_SYS_CONFIG_BUS_CLK*/
 
-unsigned long get_tbclk (void)
-{
-	return CONFIG_SYS_BUS_HZ / 4;
-}
-#endif	/* CONFIG_AMIGAONEG3SE or CONFIG_SYS_CONFIG_BUS_CLK*/
 /* ------------------------------------------------------------------------- */
+
 #if defined(CONFIG_WATCHDOG)
 #if !defined(CONFIG_PCIPPC2) && !defined(CONFIG_BAB7xx)
 void

board/Marvell/db64360/sdram_init.c

@@ -1290,37 +1290,37 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	case 0x0:
 	case 0x80:		/* refresh period is 15.625 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_HZ)
+			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_CLK)
 					/ (float) 1000000.0);
 		break;
 	case 0x1:
 	case 0x81:		/* refresh period is 3.9 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x2:
 	case 0x82:		/* refresh period is 7.8 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x3:
 	case 0x83:		/* refresh period is 31.3 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x4:
 	case 0x84:		/* refresh period is 62.5 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x5:
 	case 0x85:		/* refresh period is 125 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	default:		/* refresh period undefined */

board/Marvell/db64460/sdram_init.c

@@ -1289,37 +1289,37 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	case 0x0:
 	case 0x80:		/* refresh period is 15.625 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_HZ)
+			(unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_CLK)
 					/ (float) 1000000.0);
 		break;
 	case 0x1:
 	case 0x81:		/* refresh period is 3.9 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x2:
 	case 0x82:		/* refresh period is 7.8 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x3:
 	case 0x83:		/* refresh period is 31.3 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x4:
 	case 0x84:		/* refresh period is 62.5 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	case 0x5:
 	case 0x85:		/* refresh period is 125 usec */
 		sdram_config_reg =
-			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_HZ) /
+			(unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_CLK) /
 					(float) 1000000.0);
 		break;
 	default:		/* refresh period undefined */

board/evb64260/mpsc.c

@@ -390,7 +390,7 @@ galbrg_set_baudrate(int channel, int rate)
 
 #if defined(CONFIG_ZUMA_V2) || defined(CONFIG_P3G4)
 	/* from tclk */
-	clock = (CONFIG_SYS_BUS_HZ/(16*rate)) - 1;
+	clock = (CONFIG_SYS_BUS_CLK/(16*rate)) - 1;
 #else
 	clock = (3686400/(16*rate)) - 1;
 #endif

include/configs/BAB7xx.h

@@ -436,9 +436,8 @@ extern unsigned char   scsi_sym53c8xx_ccf;
 extern  unsigned long           bab7xx_get_bus_freq (void);
 extern  unsigned long           bab7xx_get_gclk_freq (void);
 #endif
-#define CONFIG_SYS_BUS_HZ              bab7xx_get_bus_freq()
-#define CONFIG_SYS_BUS_CLK             CONFIG_SYS_BUS_HZ
-#define CONFIG_SYS_CPU_CLK             bab7xx_get_gclk_freq()
+#define CONFIG_SYS_BUS_CLK	bab7xx_get_bus_freq()
+#define CONFIG_SYS_CPU_CLK	bab7xx_get_gclk_freq()
 
 /*
  * For booting Linux, the board info and command line data

include/configs/CPCI750.h

@@ -234,8 +234,7 @@
 #define CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 

include/configs/DB64360.h

@@ -318,8 +318,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
 /*ronen - this the Sys clock (cpu bus,internal dram and SDRAM) */
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
 
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 400MHZ -> 5.0 ns, for 133MHZ -> 7.50 ns */

include/configs/DB64460.h

@@ -256,8 +256,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
 /*ronen - this the Sys clock (cpu bus,internal dram and SDRAM) */
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz (CPU = 5*Bus = 666MHz)		*/
 
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 200MHZ -> 5.0 ns, 166MHZ -> 6.0, 133MHZ -> 7.50 ns */

include/configs/ELPPC.h

@@ -314,9 +314,8 @@
 /*
  * Speed settings are board specific
  */
-#define CONFIG_SYS_BUS_HZ              100000000
-#define CONFIG_SYS_CPU_CLK             400000000
-#define CONFIG_SYS_BUS_CLK             CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK	100000000
+#define CONFIG_SYS_CPU_CLK	400000000
 
 /*
  * For booting Linux, the board info and command line data

include/configs/EVB64260.h

@@ -141,8 +141,7 @@
 #define	CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks	*/
-#define CONFIG_SYS_BUS_HZ		100000000	/* 100 MHz		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		100000000	/* 100 MHz		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 

include/configs/P3G4.h

@@ -168,8 +168,7 @@
 #define	CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks	*/
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz		*/
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 

include/configs/PCIPPC2.h

@@ -194,9 +194,8 @@
  * For the detail description refer to the PCIPPC2 user's manual.
  */
 #define CONFIG_SYS_HZ		      1000
-#define CONFIG_SYS_BUS_HZ            100000000 /* bus speed - 100 mhz          */
+#define CONFIG_SYS_BUS_CLK            100000000 /* bus speed - 100 mhz          */
 #define CONFIG_SYS_CPU_CLK	      300000000
-#define CONFIG_SYS_BUS_CLK	      100000000
 
 /*
  * For booting Linux, the board info and command line data

include/configs/PCIPPC6.h

@@ -196,9 +196,8 @@
  * For the detail description refer to the PCIPPC2 user's manual.
  */
 #define CONFIG_SYS_HZ		      1000
-#define CONFIG_SYS_BUS_HZ	      100000000 /* bus speed - 100 mhz		*/
+#define CONFIG_SYS_BUS_CLK	      100000000 /* bus speed - 100 mhz		*/
 #define CONFIG_SYS_CPU_CLK	      300000000
-#define CONFIG_SYS_BUS_CLK	      100000000
 
 /*
  * For booting Linux, the board info and command line data

include/configs/ZUMA.h

@@ -164,9 +164,7 @@
 
 #define CONFIG_SYS_HZ			1000		/* decr freq: 1ms ticks */
 
-#define CONFIG_SYS_BUS_HZ		133000000	/* 133 MHz		*/
-
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133000000	/* 133 MHz		*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 

include/configs/mpc7448hpc2.h

@@ -46,7 +46,7 @@
 #define CONFIG_IDENT_STRING	" Freescale MPC7448 HPC II"
 
 #define CONFIG_SYS_OCN_CLK		133000000	/* 133 MHz */
-#define CONFIG_SYS_CONFIG_BUS_CLK	133000000
+#define CONFIG_SYS_BUS_CLK		133000000
 
 #define CONFIG_SYS_CLK_SPREAD		/* Enable Spread-Spectrum Clock generation */
 

include/configs/p3mx.h

@@ -44,14 +44,12 @@
 #define CONFIG_750FX			/* 750GL/GX/FX			*/
 #define CONFIG_HIGH_BATS		/* High BATs supported		*/
 #define CONFIG_SYS_BOARD_NAME		"P3M750"
-#define CONFIG_SYS_BUS_HZ		100000000
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		100000000
 #define CONFIG_SYS_TCLK		100000000
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_74xx
 #define CONFIG_SYS_BOARD_NAME		"P3M7448"
-#define CONFIG_SYS_BUS_HZ		133333333
-#define CONFIG_SYS_BUS_CLK		CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK		133333333
 #define CONFIG_SYS_TCLK		133333333
 #endif
 #define CONFIG_SYS_GT_DUAL_CPU			/* also for JTAG even with one cpu */

include/configs/ppmc7xx.h

@@ -355,12 +355,10 @@
 /*
  * Clocks config
  *
- * CONFIG_SYS_BUS_HZ			- Bus clock frequency in Hz
- * CONFIG_SYS_BUS_CLK			- As above (?)
+ * CONFIG_SYS_BUS_CLK			- Bus clock frequency in Hz
  * CONFIG_SYS_HZ			- Decrementer freq in Hz
  */
 
-#define CONFIG_SYS_BUS_HZ		CONFIG_BUS_CLK
 #define CONFIG_SYS_BUS_CLK		CONFIG_BUS_CLK
 #define CONFIG_SYS_HZ			1000