ARM: bcm283x: don't always define CONFIG_BCM2835

Currently, CONFIG_BCM2835 is defined for all BCM283x builds and _BCM2836
is defined when building for that SoC. That means there isn't a single
define that means "exactly BCM2835". This will complicate future patches
where BCM2835-vs-anything-else needs to be determined simply.

Modify the code to define one or the other of CONFIG_BCM2835/BCM2836 so
future patches are simpler.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

arch/arm/mach-bcm283x/include/mach/gpio.h

@@ -9,7 +9,7 @@
 #ifndef _BCM2835_GPIO_H_
 #define _BCM2835_GPIO_H_
 
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 #define BCM2835_GPIO_BASE		0x3f200000
 #else
 #define BCM2835_GPIO_BASE		0x20200000

arch/arm/mach-bcm283x/include/mach/mbox.h

@@ -38,7 +38,7 @@
 
 /* Raw mailbox HW */
 
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 #define BCM2835_MBOX_PHYSADDR	0x3f00b880
 #else
 #define BCM2835_MBOX_PHYSADDR	0x2000b880

arch/arm/mach-bcm283x/include/mach/sdhci.h

@@ -7,7 +7,7 @@
 #ifndef _BCM2835_SDHCI_H_
 #define _BCM2835_SDHCI_H_
 
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 #define BCM2835_SDHCI_BASE 0x3f300000
 #else
 #define BCM2835_SDHCI_BASE 0x20300000

arch/arm/mach-bcm283x/include/mach/timer.h

@@ -7,7 +7,7 @@
 #ifndef _BCM2835_TIMER_H
 #define _BCM2835_TIMER_H
 
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 #define BCM2835_TIMER_PHYSADDR	0x3f003000
 #else
 #define BCM2835_TIMER_PHYSADDR	0x20003000

arch/arm/mach-bcm283x/include/mach/wdog.h

@@ -7,7 +7,7 @@
 #ifndef _BCM2835_WDOG_H
 #define _BCM2835_WDOG_H
 
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 #define BCM2835_WDOG_PHYSADDR			0x3f100000
 #else
 #define BCM2835_WDOG_PHYSADDR			0x20100000

arch/arm/mach-bcm283x/phys2bus.c

@@ -9,7 +9,7 @@
 
 unsigned long phys_to_bus(unsigned long phys)
 {
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 	return 0xc0000000 | phys;
 #else
 	return 0x40000000 | phys;

board/raspberrypi/rpi/rpi.c

@@ -31,7 +31,7 @@ U_BOOT_DEVICE(bcm2835_gpios) = {
 };
 
 static const struct pl01x_serial_platdata serial_platdata = {
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 	.base = 0x3f201000,
 #else
 	.base = 0x20201000,

include/configs/rpi-common.h

@@ -11,7 +11,6 @@
 #include <asm/arch/timer.h>
 
 /* Architecture, CPU, etc.*/
-#define CONFIG_BCM2835
 #define CONFIG_ARCH_CPU_INIT
 
 #define CONFIG_SYS_TIMER_RATE		1000000
@@ -26,7 +25,7 @@
  * chose to use someone else's previously registered machine ID (3139, MX51_GGC)
  * rather than obtaining a valid ID:-/
  */
-#ifndef CONFIG_BCM2836
+#ifdef CONFIG_BCM2835
 #define CONFIG_MACH_TYPE		MACH_TYPE_BCM2708
 #endif
 
@@ -80,7 +79,7 @@
 #define CONFIG_CMD_USB
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_DWC2
-#ifdef CONFIG_BCM2836
+#ifndef CONFIG_BCM2835
 #define CONFIG_USB_DWC2_REG_ADDR 0x3f980000
 #else
 #define CONFIG_USB_DWC2_REG_ADDR 0x20980000

include/configs/rpi.h

@@ -7,6 +7,7 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_BCM2835
 #define CONFIG_SYS_CACHELINE_SIZE		32
 
 #include "rpi-common.h"