Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- Fix device tree of Avenger96 board from Arrow Electronics and add
  compatibility with stm32mp15_dhcom_basic_defconfig

arch/arm/dts/stm32mp157-pinctrl.dtsi

@@ -288,6 +288,57 @@
 				};
 			};
 
+			ethernet0_rgmii_pins_b: rgmii-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+						 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+						 <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */
+						 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+						 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+						 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+						 <STM32_PINMUX('G', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+						 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins3 {
+					pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+						 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+						 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+						 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+						 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+						 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+					bias-disable;
+				};
+			};
+
+			ethernet0_rgmii_pins_sleep_b: rgmii-sleep-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+						 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+						 <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */
+						 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+						 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+						 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+						 <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+						 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+						 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+						 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+						 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+						 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+						 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+						 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+						 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+				};
+			};
+
 			fmc_pins_a: fmc-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
@@ -832,6 +883,30 @@
 				};
 			};
 
+			sdmmc1_dir_pins_b: sdmmc1-dir-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+						 <STM32_PINMUX('E', 14, AF8)>, /* SDMMC1_D123DIR */
+						 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+					slew-rate = <1>;
+					drive-push-pull;
+					bias-pull-up;
+				};
+				pins2{
+					pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+					bias-pull-up;
+				};
+			};
+
+			sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 {
+				pins {
+					pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+						 <STM32_PINMUX('E', 14, ANALOG)>, /* SDMMC1_D123DIR */
+						 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+						 <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+				};
+			};
+
 			sdmmc2_b4_pins_a: sdmmc2-b4-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
@@ -907,6 +982,27 @@
 				};
 			};
 
+			sdmmc2_d47_pins_b: sdmmc2-d47-1 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+						 <STM32_PINMUX('A', 15, AF9)>, /* SDMMC2_D5 */
+						 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+						 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+					slew-rate = <1>;
+					drive-push-pull;
+					bias-pull-up;
+				};
+			};
+
+			sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+						 <STM32_PINMUX('A', 15, ANALOG)>, /* SDMMC2_D5 */
+						 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+						 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+				};
+			};
+
 			spdifrx_pins_a: spdifrx-0 {
 				pins {
 					pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */

arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi

@@ -150,9 +150,12 @@
 	};
 };
 
-&sdmmc1_dir_pins_a {
+&sdmmc1_dir_pins_b {
 	u-boot,dm-spl;
-	pins {
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
 		u-boot,dm-spl;
 	};
 };
@@ -171,7 +174,7 @@
 	};
 };
 
-&sdmmc2_d47_pins_a {
+&sdmmc2_d47_pins_b {
 	u-boot,dm-spl;
 	pins {
 		u-boot,dm-spl;

arch/arm/dts/stm32mp157a-avenger96.dts

@@ -16,10 +16,12 @@
 	compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
 
 	aliases {
+		eeprom0 = &eeprom0;
 		ethernet0 = &ethernet0;
 		mmc0 = &sdmmc1;
 		serial0 = &uart4;
 		serial1 = &uart7;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -76,16 +78,42 @@
 			default-state = "off";
 		};
 	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
+	vdd_io: regulator-buck-io {
+		compatible = "regulator-fixed";
+		regulator-name = "buck-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
 };
 
 &ethernet0 {
 	status = "okay";
-	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
+	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_b>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rgmii";
 	max-speed = <1000>;
 	phy-handle = <&phy0>;
+	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
 
 	mdio0 {
 		#address-cells = <1>;
@@ -151,7 +179,7 @@
 
 			vddcore: buck1 {
 				regulator-name = "vddcore";
-				regulator-min-microvolt = <1200000>;
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
@@ -169,8 +197,8 @@
 
 			vdd: buck3 {
 				regulator-name = "vdd";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
 				regulator-always-on;
 				st,mask_reset;
 				regulator-initial-mode = <0>;
@@ -252,6 +280,7 @@
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
 				interrupt-parent = <&pmic>;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
@@ -274,6 +303,12 @@
 			status = "disabled";
 		};
 	};
+
+	eeprom0: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
 };
 
 &iwdg2 {
@@ -282,10 +317,29 @@
 };
 
 &pwr_regulators {
-	vdd-supply = <&vdd>;
+	vdd-supply = <&vdd_io>;
 	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
 
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &rng1 {
 	status = "okay";
 };
@@ -296,21 +350,24 @@
 
 &sdmmc1 {
 	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
-	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
-	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
-	broken-cd;
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	cd-gpios = <&gpioi 8 GPIO_ACTIVE_LOW>;
+	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
 	st,use-ckin;
+	sd-uhs-sdr104;
 	bus-width = <4>;
 	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
 	status = "okay";
 };
 
 &sdmmc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
 	non-removable;
 	no-sd;
 	no-sdio;

arch/arm/dts/stm32mp15xx-dhcom.dtsi

@@ -10,6 +10,10 @@
 #include <dt-bindings/mfd/st,stpmic1.h>
 
 / {
+	aliases {
+		eeprom0 = &eeprom0;
+	};
+
 	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xC0000000 0x40000000>;
@@ -187,7 +191,7 @@
 		};
 	};
 
-	eeprom@50 {
+	eeprom0: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;

board/dhelectronics/dh_stm32mp1/board.c

@@ -78,22 +78,21 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int setup_mac_address(void)
 {
-	struct udevice *dev;
-	ofnode eeprom;
 	unsigned char enetaddr[6];
-	int ret;
+	struct udevice *dev;
+	int off, ret;
 
 	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
 	if (ret)	/* ethaddr is already set */
 		return 0;
 
-	eeprom = ofnode_path("/soc/i2c@5c002000/eeprom@50");
-	if (!ofnode_valid(eeprom)) {
-		printf("Invalid hardware path to EEPROM!\n");
-		return -ENODEV;
+	off = fdt_path_offset(gd->fdt_blob, "eeprom0");
+	if (off < 0) {
+		printf("%s: No eeprom0 path offset\n", __func__);
+		return off;
 	}
 
-	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom, &dev);
+	ret = uclass_get_device_by_of_offset(UCLASS_I2C_EEPROM, off, &dev);
 	if (ret) {
 		printf("Cannot find EEPROM!\n");
 		return ret;