bfin: Remove spi dma function in bf5xx.

BF5xx rx dma causes spi flash random read error.
Accually spi controller has problems both on tx and rx dma.
So remove spi dma support in u-boot.
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>

drivers/spi/bfin_spi.c

@@ -13,7 +13,6 @@
 #include <spi.h>
 
 #include <asm/blackfin.h>
-#include <asm/dma.h>
 #include <asm/gpio.h>
 #include <asm/portmux.h>
 #include <asm/mach-common/bits/spi.h>
@@ -242,106 +241,10 @@ void spi_release_bus(struct spi_slave *slave)
 	SSYNC();
 }
 
-#ifdef __ADSPBF54x__
-# define SPI_DMA_BASE DMA4_NEXT_DESC_PTR
-#elif defined(__ADSPBF533__) || defined(__ADSPBF532__) || defined(__ADSPBF531__) || \
-      defined(__ADSPBF538__) || defined(__ADSPBF539__)
-# define SPI_DMA_BASE DMA5_NEXT_DESC_PTR
-#elif defined(__ADSPBF561__)
-# define SPI_DMA_BASE DMA2_4_NEXT_DESC_PTR
-#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) || \
-      defined(__ADSPBF52x__) || defined(__ADSPBF51x__)
-# define SPI_DMA_BASE DMA7_NEXT_DESC_PTR
-# elif defined(__ADSPBF50x__)
-# define SPI_DMA_BASE DMA6_NEXT_DESC_PTR
-#else
-# error "Please provide SPI DMA channel defines"
-#endif
-static volatile struct dma_register *dma = (void *)SPI_DMA_BASE;
-
 #ifndef CONFIG_BFIN_SPI_IDLE_VAL
 # define CONFIG_BFIN_SPI_IDLE_VAL 0xff
 #endif
 
-#ifdef CONFIG_BFIN_SPI_NO_DMA
-# define SPI_DMA 0
-#else
-# define SPI_DMA 1
-#endif
-
-static int spi_dma_xfer(struct bfin_spi_slave *bss, const u8 *tx, u8 *rx,
-			uint bytes)
-{
-	int ret = -1;
-	u16 ndsize, spi_config, dma_config;
-	struct dmasg dmasg[2];
-	const u8 *buf;
-
-	if (tx) {
-		debug("%s: doing half duplex TX\n", __func__);
-		buf = tx;
-		spi_config = TDBR_DMA;
-		dma_config = 0;
-	} else {
-		debug("%s: doing half duplex RX\n", __func__);
-		buf = rx;
-		spi_config = RDBR_DMA;
-		dma_config = WNR;
-	}
-
-	dmasg[0].start_addr = (unsigned long)buf;
-	dmasg[0].x_modify = 1;
-	dma_config |= WDSIZE_8 | DMAEN;
-	if (bytes <= 65536) {
-		blackfin_dcache_flush_invalidate_range(buf, buf + bytes);
-		ndsize = NDSIZE_5;
-		dmasg[0].cfg = NDSIZE_0 | dma_config | FLOW_STOP | DI_EN;
-		dmasg[0].x_count = bytes;
-	} else {
-		blackfin_dcache_flush_invalidate_range(buf, buf + 65536 - 1);
-		ndsize = NDSIZE_7;
-		dmasg[0].cfg = NDSIZE_5 | dma_config | FLOW_ARRAY | DMA2D;
-		dmasg[0].x_count = 0;	/* 2^16 */
-		dmasg[0].y_count = bytes >> 16;	/* count / 2^16 */
-		dmasg[0].y_modify = 1;
-		dmasg[1].start_addr = (unsigned long)(buf + (bytes & ~0xFFFF));
-		dmasg[1].cfg = NDSIZE_0 | dma_config | FLOW_STOP | DI_EN;
-		dmasg[1].x_count = bytes & 0xFFFF; /* count % 2^16 */
-		dmasg[1].x_modify = 1;
-	}
-
-	dma->cfg = 0;
-	dma->irq_status = DMA_DONE | DMA_ERR;
-	dma->curr_desc_ptr = dmasg;
-	write_SPI_CTL(bss, (bss->ctl & ~TDBR_CORE));
-	write_SPI_STAT(bss, -1);
-	SSYNC();
-
-	write_SPI_TDBR(bss, CONFIG_BFIN_SPI_IDLE_VAL);
-	dma->cfg = ndsize | FLOW_ARRAY | DMAEN;
-	write_SPI_CTL(bss, (bss->ctl & ~TDBR_CORE) | spi_config);
-	SSYNC();
-
-	/*
-	 * We already invalidated the first 64k,
-	 * now while we just wait invalidate the remaining part.
-	 * Its not likely that the DMA is going to overtake
-	 */
-	if (bytes > 65536)
-		blackfin_dcache_flush_invalidate_range(buf + 65536, buf + bytes);
-
-	while (!(dma->irq_status & DMA_DONE))
-		if (ctrlc())
-			goto done;
-
-	dma->cfg = 0;
-
-	ret = 0;
- done:
-	write_SPI_CTL(bss, bss->ctl);
-	return ret;
-}
-
 static int spi_pio_xfer(struct bfin_spi_slave *bss, const u8 *tx, u8 *rx,
 			uint bytes)
 {
@@ -393,11 +296,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
 	if (flags & SPI_XFER_BEGIN)
 		spi_cs_activate(slave);
 
-	/* TX DMA doesn't work quite right */
-	if (SPI_DMA && bytes > 6 && (!tx /*|| !rx*/))
-		ret = spi_dma_xfer(bss, tx, rx, bytes);
-	else
-		ret = spi_pio_xfer(bss, tx, rx, bytes);
+	ret = spi_pio_xfer(bss, tx, rx, bytes);
 
  done:
 	if (flags & SPI_XFER_END)