split IVM power hooks from cmd_ide.c

Move power control code from ide_reset() into IVM-specific IDE reset code.
Signed-off-by: NPavel Herrmann <morpheus.ibis@gmail.com>

board/ivm/ivm.c

@@ -333,13 +333,59 @@ void show_boot_progress (int status)
 void ide_set_reset (int on)
 {
 	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+	int i;
 
 	/*
 	 * Configure PC for IDE Reset Pin
 	 */
 	if (on) {		/* assert RESET */
 		immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_IDE_RESET);
+
+#ifdef CONFIG_SYS_PB_12V_ENABLE
+		/* 12V Enable output OFF */
+		immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_12V_ENABLE);
+
+		immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_12V_ENABLE);
+		immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_12V_ENABLE);
+		immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_12V_ENABLE;
+
+		/* wait 500 ms for the voltage to stabilize */
+		for (i = 0; i < 500; ++i)
+			udelay(1000);
+#endif /* CONFIG_SYS_PB_12V_ENABLE */
 	} else {		/* release RESET */
+#ifdef CONFIG_SYS_PB_12V_ENABLE
+		/* 12V Enable output ON */
+		immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_12V_ENABLE;
+#endif /* CONFIG_SYS_PB_12V_ENABLE */
+
+#ifdef CONFIG_SYS_PB_IDE_MOTOR
+		/* configure IDE Motor voltage monitor pin as input */
+		immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+		immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+		immr->im_cpm.cp_pbdir &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+
+/* wait up to 1 s for the motor voltage to stabilize */
+		for (i = 0; i < 1000; ++i) {
+			if ((immr->im_cpm.cp_pbdat
+					& CONFIG_SYS_PB_IDE_MOTOR) != 0)
+				break;
+			udelay(1000);
+		}
+
+		if (i == 1000) {	/* Timeout */
+			printf("\nWarning: 5V for IDE Motor missing\n");
+#ifdef CONFIG_STATUS_LED
+#ifdef STATUS_LED_YELLOW
+			status_led_set(STATUS_LED_YELLOW, STATUS_LED_ON);
+#endif
+#ifdef STATUS_LED_GREEN
+			status_led_set(STATUS_LED_GREEN, STATUS_LED_OFF);
+#endif
+#endif /* CONFIG_STATUS_LED */
+		}
+#endif /* CONFIG_SYS_PB_IDE_MOTOR */
+
 		immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_IDE_RESET;
 	}
 

common/cmd_ide.c

@@ -1169,9 +1169,6 @@ extern void ide_set_reset(int idereset);
 
 static void ide_reset(void)
 {
-#if defined(CONFIG_SYS_PB_12V_ENABLE) || defined(CONFIG_SYS_PB_IDE_MOTOR)
-	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-#endif
 	int i;
 
 	curr_device = -1;
@@ -1187,51 +1184,6 @@ static void ide_reset(void)
 
 	WATCHDOG_RESET();
 
-#ifdef CONFIG_SYS_PB_12V_ENABLE
-	/* 12V Enable output OFF */
-	immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_12V_ENABLE);
-
-	immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_12V_ENABLE);
-	immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_12V_ENABLE);
-	immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_12V_ENABLE;
-
-	/* wait 500 ms for the voltage to stabilize */
-	for (i = 0; i < 500; ++i)
-		udelay(1000);
-
-	/* 12V Enable output ON */
-	immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_12V_ENABLE;
-#endif /* CONFIG_SYS_PB_12V_ENABLE */
-
-#ifdef CONFIG_SYS_PB_IDE_MOTOR
-	/* configure IDE Motor voltage monitor pin as input */
-	immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_IDE_MOTOR);
-	immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_IDE_MOTOR);
-	immr->im_cpm.cp_pbdir &= ~(CONFIG_SYS_PB_IDE_MOTOR);
-
-	/* wait up to 1 s for the motor voltage to stabilize */
-	for (i = 0; i < 1000; ++i) {
-		if ((immr->im_cpm.cp_pbdat & CONFIG_SYS_PB_IDE_MOTOR) != 0) {
-			break;
-		}
-		udelay(1000);
-	}
-
-	if (i == 1000) {	/* Timeout */
-		printf("\nWarning: 5V for IDE Motor missing\n");
-#ifdef CONFIG_STATUS_LED
-#ifdef STATUS_LED_YELLOW
-		status_led_set(STATUS_LED_YELLOW, STATUS_LED_ON);
-#endif
-#ifdef STATUS_LED_GREEN
-		status_led_set(STATUS_LED_GREEN, STATUS_LED_OFF);
-#endif
-#endif /* CONFIG_STATUS_LED */
-	}
-#endif /* CONFIG_SYS_PB_IDE_MOTOR */
-
-	WATCHDOG_RESET();
-
 	/* de-assert RESET signal */
 	ide_set_reset(0);