board: fsl: lx2160aqds: identify SDHC adapter during board init

Add support for SDHC adapter identification and configuration
during board init.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

board/freescale/common/qixis.h

@@ -36,7 +36,12 @@ struct qixis {
 	u8 gdc;
 	u8 gdd;         /* DCM Debug Data Register,0x17 */
 	u8 dmack;
-	u8 res1[6];
+	u8 res1;
+	u8 sdhc1;
+	u8 sdhc2;
+	u8 stat_pres3;
+	u8 los_stat;
+	u8 usb_ctl;
 	u8 watch;       /* Watchdog Register,0x1F */
 	u8 pwr_ctl[2];  /* Power Control Register,0x20 */
 	u8 res2[2];
@@ -117,6 +122,7 @@ void qixis_write_i2c(unsigned int reg, u8 value);
 
 /* Use for SDHC adapter card type identification and operation */
 #define QIXIS_SDID_MASK                         0x07
+
 #define QIXIS_ESDHC_ADAPTER_TYPE_EMMC45         0x1	/* eMMC Card Rev4.5 */
 #define QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY   0x2	/* SD/MMC Legacy Card */
 #define QIXIS_ESDHC_ADAPTER_TYPE_EMMC44         0x3	/* eMMC Card Rev4.4 */
@@ -125,6 +131,9 @@ void qixis_write_i2c(unsigned int reg, u8 value);
 #define QIXIS_ESDHC_ADAPTER_TYPE_SD             0x6	/* SD Card Rev2.0 3.0 */
 #define QIXIS_ESDHC_NO_ADAPTER                  0x7	/* No Card is Present*/
 
+#define QIXIS_SDHC1_S1V3	0x80	/* SDHC1: SDHC1 3.3V power control */
+#define QIXIS_SDHC1_VS		0x30	/* BRDCFG11: route to SDHC1_VS */
+
 #define QIXIS_SDCLKIN		0x08
 #define QIXIS_SDCLKOUT		0x02
 #define QIXIS_DAT5_6_7		0X02

board/freescale/lx2160a/lx2160a.c

@@ -18,6 +18,7 @@
 #include <fdt_support.h>
 #include <linux/bitops.h>
 #include <linux/libfdt.h>
+#include <linux/delay.h>
 #include <fsl-mc/fsl_mc.h>
 #include <env_internal.h>
 #include <efi_loader.h>
@@ -379,7 +380,7 @@ int checkboard(void)
  */
 u8 qixis_esdhc_detect_quirk(void)
 {
-	/* for LX2160AQDS res1[1] @ offset 0x1A is SDHC1 Control/Status (SDHC1)
+	/*
 	 * SDHC1 Card ID:
 	 * Specifies the type of card installed in the SDHC1 adapter slot.
 	 * 000= (reserved)
@@ -391,10 +392,35 @@ u8 qixis_esdhc_detect_quirk(void)
 	 * 110= SDCard V2/V3 adapter installed.
 	 * 111= no adapter is installed.
 	 */
-	return ((QIXIS_READ(res1[1]) & QIXIS_SDID_MASK) !=
+	return ((QIXIS_READ(sdhc1) & QIXIS_SDID_MASK) !=
 		 QIXIS_ESDHC_NO_ADAPTER);
 }
 
+static void esdhc_adapter_card_ident(void)
+{
+	u8 card_id, val;
+
+	val = QIXIS_READ(sdhc1);
+	card_id = val & QIXIS_SDID_MASK;
+
+	switch (card_id) {
+	case QIXIS_ESDHC_ADAPTER_TYPE_SD:
+		/* Power cycle to card */
+		val &= ~QIXIS_SDHC1_S1V3;
+		QIXIS_WRITE(sdhc1, val);
+		mdelay(1);
+		val |= QIXIS_SDHC1_S1V3;
+		QIXIS_WRITE(sdhc1, val);
+		/* Route to SDHC1_VS */
+		val = QIXIS_READ(brdcfg[11]);
+		val |= QIXIS_SDHC1_VS;
+		QIXIS_WRITE(brdcfg[11], val);
+		break;
+	default:
+		break;
+	}
+}
+
 int config_board_mux(void)
 {
 	u8 reg11, reg5, reg13;
@@ -501,6 +527,12 @@ int config_board_mux(void)
 
 	return 0;
 }
+
+int board_early_init_r(void)
+{
+	esdhc_adapter_card_ident();
+	return 0;
+}
 #elif defined(CONFIG_TARGET_LX2160ARDB)
 int config_board_mux(void)
 {