sunxi: Split out common board design for ALL-H3-CC device tree

The Libre Computer Project ALL-H3-CC has three models, all using the
same board design, but with different pin compatible SoCs and amount of
DRAM.

Currently only the H3 1GB DRAM variant is supported. To support the two
other variants, first split the original device tree into a common board
design part and an SoC specific part.

The SoC part only defines which SoC is used and model name, and includes
the SoC specific dtsi file and the common design dtsi file.

Also fix up the SPDX identifier line to use the correct comment style,
and place it on the first line.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
- *
- * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
  */
 
 /dts-v1/;
 #include "sun8i-h3.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sunxi-libretech-all-h3-cc.dtsi"
 
 / {
 	model = "Libre Computer Board ALL-H3-CC H3";
 	compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3";
-
-	aliases {
-		ethernet0 = &emac;
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		pwr_led {
-			label = "librecomputer:green:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-			default-state = "on";
-		};
-
-		status_led {
-			label = "librecomputer:blue:status";
-			gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "power";
-			linux,code = <KEY_POWER>;
-			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
-		};
-	};
-
-	reg_vcc1v2: vcc1v2 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc1v2";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_vcc5v0>;
-		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
-		enable-active-high;
-	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&reg_vcc5v0>;
-	};
-
-	/* This represents the board's 5V input */
-	reg_vcc5v0: vcc5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_vcc_dram: vcc-dram {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc-dram";
-		regulator-min-microvolt = <1500000>;
-		regulator-max-microvolt = <1500000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_vcc5v0>;
-		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
-		enable-active-high;
-	};
-
-	reg_vcc_io: vcc-io {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc-io";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_vcc3v3>;
-		gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
-	};
-
-	reg_vdd_cpux: vdd-cpux {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd-cpux";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_vcc5v0>;
-		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
-		enable-active-high;
-	};
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&ehci2 {
-	status = "okay";
-};
-
-&ehci3 {
-	status = "okay";
-};
-
-&emac {
-	phy-handle = <&int_mii_phy>;
-	phy-mode = "mii";
-	allwinner,leds-active-low;
-	status = "okay";
-};
-
-&ir {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
-	status = "okay";
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>;
-	vmmc-supply = <&reg_vcc_io>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&ohci3 {
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&usbphy {
-	/* VBUS on USB ports are always on */
-	usb0_vbus-supply = <&reg_vcc5v0>;
-	usb1_vbus-supply = <&reg_vcc5v0>;
-	usb2_vbus-supply = <&reg_vcc5v0>;
-	usb3_vbus-supply = <&reg_vcc5v0>;
-	status = "okay";
 };

arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr_led {
+			label = "librecomputer:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+
+		status_led {
+			label = "librecomputer:blue:status";
+			gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		};
+	};
+
+	reg_vcc1v2: vcc1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v2";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-active-high;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	/* This represents the board's 5V input */
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		enable-active-high;
+	};
+
+	reg_vcc_io: vcc-io {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-io";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc3v3>;
+		gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+	};
+
+	reg_vdd_cpux: vdd-cpux {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpux";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-active-high;
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>;
+	vmmc-supply = <&reg_vcc_io>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	/* VBUS on USB ports are always on */
+	usb0_vbus-supply = <&reg_vcc5v0>;
+	usb1_vbus-supply = <&reg_vcc5v0>;
+	usb2_vbus-supply = <&reg_vcc5v0>;
+	usb3_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};