armv8: dts: fsl-lx2160a: add i2c controller and gpio DT nodes

In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.
Signed-off-by: NChuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

arch/arm/dts/fsl-lx2160a.dtsi

@@ -49,6 +49,80 @@
 			     <1 10 0x8>; /* Hypervisor PPI, active-low */
 	};
 
+	i2c0: i2c@2000000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2000000 0x0 0x10000>;
+		interrupts = <0 34 4>;
+		scl-gpio = <&gpio2 15 0>;
+		status = "disabled";
+	};
+
+	i2c1: i2c@2010000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2010000 0x0 0x10000>;
+		interrupts = <0 34 4>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@2020000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2020000 0x0 0x10000>;
+		interrupts = <0 35 4>;
+		status = "disabled";
+	};
+
+	i2c3: i2c@2030000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2030000 0x0 0x10000>;
+		interrupts = <0 35 4>;
+		status = "disabled";
+	};
+
+	i2c4: i2c@2040000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2040000 0x0 0x10000>;
+		interrupts = <0 74 4>;
+		scl-gpio = <&gpio2 16 0>;
+		status = "disabled";
+	};
+
+	i2c5: i2c@2050000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2050000 0x0 0x10000>;
+		interrupts = <0 74 4>;
+		status = "disabled";
+	};
+
+	i2c6: i2c@2060000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2060000 0x0 0x10000>;
+		interrupts = <0 75 4>;
+		status = "disabled";
+	};
+
+	i2c7: i2c@2070000 {
+		compatible = "fsl,vf610-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x2070000 0x0 0x10000>;
+		interrupts = <0 75 4>;
+		status = "disabled";
+	};
+
 	uart0: serial@21c0000 {
 		compatible = "arm,pl011";
 		reg = <0x0 0x21c0000 0x0 0x1000>;
@@ -102,6 +176,17 @@
 		num-cs = <6>;
 	};
 
+	gpio2: gpio@2320000 {
+		compatible = "fsl,qoriq-gpio";
+		reg = <0x0 0x2320000 0x0 0x10000>;
+		interrupts = <0 37 4>;
+		gpio-controller;
+		little-endian;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
 	usb0: usb3@3100000 {
 		compatible = "fsl,layerscape-dwc3";
 		reg = <0x0 0x3100000 0x0 0x10000>;