include/configs: Catch some CONFIG_CMD_* conversion stragglers.

Use new CONFIG_CMD_* in lwmon5.h board config file.
Fix CONFIG_CMD_* typo braindamage in omap1510inn.h
Signed-off-by: NJon Loeliger <jdl@freescale.com>

include/configs/lwmon5.h

@@ -216,9 +216,6 @@
 /* Comment this out to enable USB 1.1 device */
 #define USB_2_0_DEVICE
 
-#define CMD_USB			CFG_CMD_USB
-#else
-#define CMD_USB			0	/* no USB on 440GRx		*/
 #endif /* CONFIG_440EPX */
 
 /* Partitions */
@@ -226,36 +223,42 @@
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
 
-#define CONFIG_COMMANDS       (CONFIG_CMD_DFL	|	\
-			       CFG_CMD_ASKENV	|	\
-			       CFG_CMD_DATE	|	\
-			       CFG_CMD_DHCP	|	\
-			       CFG_CMD_DIAG	|	\
-			       CFG_CMD_EEPROM	|	\
-			       CFG_CMD_ELF	|	\
-			       CFG_CMD_FAT	|	\
-			       CFG_CMD_I2C	|	\
-			       CFG_CMD_IRQ	|	\
-			       CFG_CMD_MII	|	\
-			       CFG_CMD_NET	|	\
-			       CFG_CMD_NFS	|	\
-			       CFG_CMD_PCI	|	\
-			       CFG_CMD_PING	|	\
-			       CFG_CMD_REGINFO	|	\
-			       CFG_CMD_SDRAM	|	\
-			       CMD_USB)
 
-#define CONFIG_SUPPORT_VFAT
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
+#ifdef CONFIG_440EPX
+#define CONFIG_CMD_USB
+#endif
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 
 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
  *----------------------------------------------------------------------*/
+#define CONFIG_SUPPORT_VFAT
+
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
@@ -418,7 +421,7 @@
  *----------------------------------------------------------------------*/
 #define CFG_DCACHE_SIZE		(32<<10)  /* For AMCC 440 CPUs			*/
 #define CFG_CACHELINE_SIZE	32	      /* ...			            */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
 #endif
 
@@ -430,7 +433,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
 #endif

include/configs/omap1510inn.h

@@ -86,8 +86,6 @@
 #define CONFIG_BAUDRATE		115200
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL
-
 
 /*
  * Command line configuration.