net: xilinx_axi_emac: Use readl and writel for io ops

This patch uses readl and writel instead of in_be32 and
out_be32 for io ops as these internally uses readl,
writel for microblaze and for Zynq, ZynqMP there is
no need of endianness conversion and readl, writel
should work straightaway. This patch starts supporting
the driver for Zynq and ZynqMP platforms.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

drivers/net/xilinx_axi_emac.c

@@ -156,7 +156,7 @@ static inline int mdio_wait(struct axi_regs *regs)
 	u32 timeout = 200;
 
 	/* Wait till MDIO interface is ready to accept a new transaction. */
-	while (timeout && (!(in_be32(&regs->mdio_mcr)
+	while (timeout && (!(readl(&regs->mdio_mcr)
 						& XAE_MDIO_MCR_READY_MASK))) {
 		timeout--;
 		udelay(1);
@@ -184,13 +184,13 @@ static u32 phyread(struct axidma_priv *priv, u32 phyaddress, u32 registernum,
 			XAE_MDIO_MCR_INITIATE_MASK |
 			XAE_MDIO_MCR_OP_READ_MASK;
 
-	out_be32(&regs->mdio_mcr, mdioctrlreg);
+	writel(mdioctrlreg, &regs->mdio_mcr);
 
 	if (mdio_wait(regs))
 		return 1;
 
 	/* Read data */
-	*val = in_be32(&regs->mdio_mrd);
+	*val = readl(&regs->mdio_mrd);
 	return 0;
 }
 
@@ -211,9 +211,9 @@ static u32 phywrite(struct axidma_priv *priv, u32 phyaddress, u32 registernum,
 			XAE_MDIO_MCR_OP_WRITE_MASK;
 
 	/* Write data */
-	out_be32(&regs->mdio_mwd, data);
+	writel(data, &regs->mdio_mwd);
 
-	out_be32(&regs->mdio_mcr, mdioctrlreg);
+	writel(mdioctrlreg, &regs->mdio_mcr);
 
 	if (mdio_wait(regs))
 		return 1;
@@ -237,7 +237,7 @@ static int axiemac_phy_init(struct udevice *dev)
 			SUPPORTED_1000baseT_Full;
 
 	/* Set default MDIO divisor */
-	out_be32(&regs->mdio_mc, XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK);
+	writel(XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK, &regs->mdio_mc);
 
 	if (priv->phyaddr == -1) {
 		/* Detect the PHY address */
@@ -316,12 +316,12 @@ static int setup_phy(struct udevice *dev)
 	}
 
 	/* Setup the emac for the phy speed */
-	emmc_reg = in_be32(&regs->emmc);
+	emmc_reg = readl(&regs->emmc);
 	emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
 	emmc_reg |= speed;
 
 	/* Write new speed setting out to Axi Ethernet */
-	out_be32(&regs->emmc, emmc_reg);
+	writel(emmc_reg, &regs->emmc);
 
 	/*
 	* Setting the operating speed of the MAC needs a delay. There
@@ -340,13 +340,13 @@ static void axiemac_stop(struct udevice *dev)
 	u32 temp;
 
 	/* Stop the hardware */
-	temp = in_be32(&priv->dmatx->control);
+	temp = readl(&priv->dmatx->control);
 	temp &= ~XAXIDMA_CR_RUNSTOP_MASK;
-	out_be32(&priv->dmatx->control, temp);
+	writel(temp, &priv->dmatx->control);
 
-	temp = in_be32(&priv->dmarx->control);
+	temp = readl(&priv->dmarx->control);
 	temp &= ~XAXIDMA_CR_RUNSTOP_MASK;
-	out_be32(&priv->dmarx->control, temp);
+	writel(temp, &priv->dmarx->control);
 
 	debug("axiemac: Halted\n");
 }
@@ -377,11 +377,11 @@ static int axi_ethernet_init(struct axidma_priv *priv)
 		 * Stop the device and reset HW
 		 * Disable interrupts
 		 */
-		out_be32(&regs->ie, 0);
+		writel(0, &regs->ie);
 	}
 
 	/* Disable the receiver */
-	out_be32(&regs->rcw1, in_be32(&regs->rcw1) & ~XAE_RCW1_RX_MASK);
+	writel(readl(&regs->rcw1) & ~XAE_RCW1_RX_MASK, &regs->rcw1);
 
 	/*
 	 * Stopping the receiver in mid-packet causes a dropped packet
@@ -389,12 +389,12 @@ static int axi_ethernet_init(struct axidma_priv *priv)
 	 */
 	if (!priv->eth_hasnobuf) {
 		/* Set the interrupt status register to clear the interrupt */
-		out_be32(&regs->is, XAE_INT_RXRJECT_MASK);
+		writel(XAE_INT_RXRJECT_MASK, &regs->is);
 	}
 
 	/* Setup HW */
 	/* Set default MDIO divisor */
-	out_be32(&regs->mdio_mc, XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK);
+	writel(XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK, &regs->mdio_mc);
 
 	debug("axiemac: InitHw done\n");
 	return 0;
@@ -409,11 +409,11 @@ static int axiemac_write_hwaddr(struct udevice *dev)
 	/* Set the MAC address */
 	int val = ((pdata->enetaddr[3] << 24) | (pdata->enetaddr[2] << 16) |
 		(pdata->enetaddr[1] << 8) | (pdata->enetaddr[0]));
-	out_be32(&regs->uaw0, val);
+	writel(val, &regs->uaw0);
 
 	val = (pdata->enetaddr[5] << 8) | pdata->enetaddr[4];
-	val |= in_be32(&regs->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK;
-	out_be32(&regs->uaw1, val);
+	val |= readl(&regs->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK;
+	writel(val, &regs->uaw1);
 	return 0;
 }
 
@@ -423,15 +423,15 @@ static void axi_dma_init(struct axidma_priv *priv)
 	u32 timeout = 500;
 
 	/* Reset the engine so the hardware starts from a known state */
-	out_be32(&priv->dmatx->control, XAXIDMA_CR_RESET_MASK);
-	out_be32(&priv->dmarx->control, XAXIDMA_CR_RESET_MASK);
+	writel(XAXIDMA_CR_RESET_MASK, &priv->dmatx->control);
+	writel(XAXIDMA_CR_RESET_MASK, &priv->dmarx->control);
 
 	/* At the initialization time, hardware should finish reset quickly */
 	while (timeout--) {
 		/* Check transmit/receive channel */
 		/* Reset is done when the reset bit is low */
-		if (!((in_be32(&priv->dmatx->control) |
-				in_be32(&priv->dmarx->control))
+		if (!((readl(&priv->dmatx->control) |
+				readl(&priv->dmarx->control))
 						& XAXIDMA_CR_RESET_MASK)) {
 			break;
 		}
@@ -460,12 +460,12 @@ static int axiemac_start(struct udevice *dev)
 		return -1;
 
 	/* Disable all RX interrupts before RxBD space setup */
-	temp = in_be32(&priv->dmarx->control);
+	temp = readl(&priv->dmarx->control);
 	temp &= ~XAXIDMA_IRQ_ALL_MASK;
-	out_be32(&priv->dmarx->control, temp);
+	writel(temp, &priv->dmarx->control);
 
 	/* Start DMA RX channel. Now it's ready to receive data.*/
-	out_be32(&priv->dmarx->current, (u32)&rx_bd);
+	writel((u32)&rx_bd, &priv->dmarx->current);
 
 	/* Setup the BD. */
 	memset(&rx_bd, 0, sizeof(rx_bd));
@@ -480,17 +480,17 @@ static int axiemac_start(struct udevice *dev)
 	flush_cache((u32)&rxframe, sizeof(rxframe));
 
 	/* Start the hardware */
-	temp = in_be32(&priv->dmarx->control);
+	temp = readl(&priv->dmarx->control);
 	temp |= XAXIDMA_CR_RUNSTOP_MASK;
-	out_be32(&priv->dmarx->control, temp);
+	writel(temp, &priv->dmarx->control);
 
 	/* Rx BD is ready - start */
-	out_be32(&priv->dmarx->tail, (u32)&rx_bd);
+	writel((u32)&rx_bd, &priv->dmarx->tail);
 
 	/* Enable TX */
-	out_be32(&regs->tc, XAE_TC_TX_MASK);
+	writel(XAE_TC_TX_MASK, &regs->tc);
 	/* Enable RX */
-	out_be32(&regs->rcw1, XAE_RCW1_RX_MASK);
+	writel(XAE_RCW1_RX_MASK, &regs->rcw1);
 
 	/* PHY setup */
 	if (!setup_phy(dev)) {
@@ -525,22 +525,22 @@ static int axiemac_send(struct udevice *dev, void *ptr, int len)
 	/* Flush the last BD so DMA core could see the updates */
 	flush_cache((u32)&tx_bd, sizeof(tx_bd));
 
-	if (in_be32(&priv->dmatx->status) & XAXIDMA_HALTED_MASK) {
+	if (readl(&priv->dmatx->status) & XAXIDMA_HALTED_MASK) {
 		u32 temp;
-		out_be32(&priv->dmatx->current, (u32)&tx_bd);
+		writel((u32)&tx_bd, &priv->dmatx->current);
 		/* Start the hardware */
-		temp = in_be32(&priv->dmatx->control);
+		temp = readl(&priv->dmatx->control);
 		temp |= XAXIDMA_CR_RUNSTOP_MASK;
-		out_be32(&priv->dmatx->control, temp);
+		writel(temp, &priv->dmatx->control);
 	}
 
 	/* Start transfer */
-	out_be32(&priv->dmatx->tail, (u32)&tx_bd);
+	writel((u32)&tx_bd, &priv->dmatx->tail);
 
 	/* Wait for transmission to complete */
 	debug("axiemac: Waiting for tx to be done\n");
 	timeout = 200;
-	while (timeout && (!(in_be32(&priv->dmatx->status) &
+	while (timeout && (!(readl(&priv->dmatx->status) &
 			(XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK)))) {
 		timeout--;
 		udelay(1);
@@ -559,10 +559,10 @@ static int isrxready(struct axidma_priv *priv)
 	u32 status;
 
 	/* Read pending interrupts */
-	status = in_be32(&priv->dmarx->status);
+	status = readl(&priv->dmarx->status);
 
 	/* Acknowledge pending interrupts */
-	out_be32(&priv->dmarx->status, status & XAXIDMA_IRQ_ALL_MASK);
+	writel(status & XAXIDMA_IRQ_ALL_MASK, &priv->dmarx->status);
 
 	/*
 	 * If Reception done interrupt is asserted, call RX call back function
@@ -587,9 +587,9 @@ static int axiemac_recv(struct udevice *dev, int flags, uchar **packetp)
 	debug("axiemac: RX data ready\n");
 
 	/* Disable IRQ for a moment till packet is handled */
-	temp = in_be32(&priv->dmarx->control);
+	temp = readl(&priv->dmarx->control);
 	temp &= ~XAXIDMA_IRQ_ALL_MASK;
-	out_be32(&priv->dmarx->control, temp);
+	writel(temp, &priv->dmarx->control);
 	if (!priv->eth_hasnobuf)
 		length = rx_bd.app4 & 0xFFFF; /* max length mask */
 	else
@@ -626,7 +626,7 @@ static int axiemac_free_pkt(struct udevice *dev, uchar *packet, int length)
 	flush_cache((u32)&rxframe, sizeof(rxframe));
 
 	/* Rx BD is ready - start again */
-	out_be32(&priv->dmarx->tail, (u32)&rx_bd);
+	writel((u32)&rx_bd, &priv->dmarx->tail);
 
 	debug("axiemac: RX completed, framelength = %d\n", length);