driver/ddr: Add support for setting timing in hws_topology_map

The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.

This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
  HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
                    from the number of CSs
  HWS_TIM_1T      - enforce 1t
  HWS_TIM_2T      - enforce 2t

This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.
Signed-off-by: NMarek Behun <marek.behun@nic.cz>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

board/Marvell/db-88f6820-amc/db-88f6820-amc.c

@@ -69,7 +69,8 @@ static struct hws_topology_map board_topology_map = {
 	    MEM_4G,			/* mem_size */
 	    DDR_FREQ_800,		/* frequency */
 	    0, 0,			/* cas_l cas_wl */
-	    HWS_TEMP_LOW} },		/* temperature */
+	    HWS_TEMP_LOW,		/* temperature */
+	    HWS_TIM_DEFAULT} },		/* timing */
 	5,				/* Num Of Bus Per Interface*/
 	BUS_MASK_32BIT			/* Busses mask */
 };

board/Marvell/db-88f6820-gp/db-88f6820-gp.c

@@ -90,7 +90,8 @@ static struct hws_topology_map board_topology_map = {
 	    MEM_4G,			/* mem_size */
 	    DDR_FREQ_800,		/* frequency */
 	    0, 0,			/* cas_l cas_wl */
-	    HWS_TEMP_LOW} },		/* temperature */
+	    HWS_TEMP_LOW,		/* temperature */
+	    HWS_TIM_DEFAULT} },		/* timing */
 	5,				/* Num Of Bus Per Interface*/
 	BUS_MASK_32BIT			/* Busses mask */
 };

board/gdsys/a38x/controlcenterdc.c

@@ -53,7 +53,8 @@ static struct hws_topology_map ddr_topology_map = {
 	    MEM_4G,			/* mem_size */
 	    DDR_FREQ_533,		/* frequency */
 	    0, 0,			/* cas_l cas_wl */
-	    HWS_TEMP_LOW} },		/* temperature */
+	    HWS_TEMP_LOW,		/* temperature */
+	    HWS_TIM_DEFAULT} },		/* timing */
 	5,				/* Num Of Bus Per Interface*/
 	BUS_MASK_32BIT			/* Busses mask */
 };

board/solidrun/clearfog/clearfog.c

@@ -83,7 +83,8 @@ static struct hws_topology_map board_topology_map = {
 	    MEM_4G,			/* mem_size */
 	    DDR_FREQ_800,		/* frequency */
 	    0, 0,			/* cas_l cas_wl */
-	    HWS_TEMP_LOW} },		/* temperature */
+	    HWS_TEMP_LOW,		/* temperature */
+	    HWS_TIM_DEFAULT} },		/* timing */
 	5,				/* Num Of Bus Per Interface*/
 	BUS_MASK_32BIT			/* Busses mask */
 };

drivers/ddr/marvell/a38x/ddr3_training.c

@@ -308,6 +308,7 @@ int hws_ddr3_tip_init_controller(u32 dev_num, struct init_cntr_param *init_cntr_
 	enum hws_speed_bin speed_bin_index = SPEED_BIN_DDR_2133N;
 	enum hws_mem_size memory_size = MEM_2G;
 	enum hws_ddr_freq freq = init_freq;
+	enum hws_timing timing;
 	u32 cs_mask = 0;
 	u32 cl_value = 0, cwl_val = 0;
 	u32 refresh_interval_cnt = 0, bus_cnt = 0, adll_tap = 0;
@@ -569,8 +570,13 @@ int hws_ddr3_tip_init_controller(u32 dev_num, struct init_cntr_param *init_cntr_
 				      DUNIT_CONTROL_HIGH_REG,
 				      (init_cntr_prm->msys_init << 7), (1 << 7)));
 
+			timing = tm->interface_params[if_id].timing;
+
 			if (mode2_t != 0xff) {
 				t2t = mode2_t;
+			} else if (timing != HWS_TIM_DEFAULT) {
+				/* Board topology map is forcing timing */
+				t2t = (timing == HWS_TIM_2T) ? 1 : 0;
 			} else {
 				/* calculate number of CS (per interface) */
 				CHECK_STATUS(calc_cs_num

drivers/ddr/marvell/a38x/ddr_topology_def.h

@@ -37,6 +37,12 @@ enum hws_mem_size {
 	MEM_SIZE_LAST
 };
 
+enum hws_timing {
+	HWS_TIM_DEFAULT,
+	HWS_TIM_1T,
+	HWS_TIM_2T
+};
+
 struct bus_params {
 	/* Chip Select (CS) bitmask (bits 0-CS0, bit 1- CS1 ...) */
 	u8 cs_bitmask;
@@ -84,6 +90,9 @@ struct if_params {
 
 	/* operation temperature */
 	enum hws_temperature interface_temp;
+
+	/* 2T vs 1T mode (by default computed from number of CSs) */
+	enum hws_timing timing;
 };
 
 struct hws_topology_map {