提交 661c9812 编写于 作者: S Sean Anderson 提交者: Tom Rini

mtd: nand: pxa3xx: Fix not calling dev_xxx with a device

Use the device from any mtd already available, or from the active mtd via
pxa3xx_nand_info if one is not.
Signed-off-by: NSean Anderson <seanga2@gmail.com>
Tested-by: NPatrick Delaunay <patrick.delaunay@st.com>
上级 b4f11dfc
......@@ -512,7 +512,7 @@ static int pxa3xx_nand_init_timings(struct pxa3xx_nand_host *host)
}
if (i == ntypes) {
dev_err(&info->pdev->dev, "Error: timings not found\n");
dev_err(mtd->dev, "Error: timings not found\n");
return -EINVAL;
}
......@@ -603,7 +603,7 @@ static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
ts = get_timer(0);
while (!(nand_readl(info, NDSR) & NDSR_RDDREQ)) {
if (get_timer(ts) > TIMEOUT_DRAIN_FIFO) {
dev_err(&info->pdev->dev,
dev_err(info->controller.active->mtd.dev,
"Timeout on RDDREQ while draining the FIFO\n");
return;
}
......@@ -656,8 +656,8 @@ static void handle_data_pio(struct pxa3xx_nand_info *info)
DIV_ROUND_UP(info->step_spare_size, 4));
break;
default:
dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
info->state);
dev_err(info->controller.active->mtd.dev,
"%s: invalid state %d\n", __func__, info->state);
BUG();
}
......@@ -1027,7 +1027,7 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
default:
exec_cmd = 0;
dev_err(&info->pdev->dev, "non-supported command %x\n",
dev_err(mtd->dev, "non-supported command %x\n",
command);
break;
}
......@@ -1087,7 +1087,7 @@ static void nand_cmdfunc(struct mtd_info *mtd, unsigned command,
break;
if (get_timer(ts) > CHIP_DELAY_TIMEOUT) {
dev_err(&info->pdev->dev, "Wait timeout!!!\n");
dev_err(mtd->dev, "Wait timeout!!!\n");
return;
}
}
......@@ -1180,7 +1180,7 @@ static void nand_cmdfunc_extended(struct mtd_info *mtd,
break;
if (get_timer(ts) > CHIP_DELAY_TIMEOUT) {
dev_err(&info->pdev->dev, "Wait timeout!!!\n");
dev_err(mtd->dev, "Wait timeout!!!\n");
return;
}
}
......@@ -1426,7 +1426,7 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
break;
if (get_timer(ts) > CHIP_DELAY_TIMEOUT) {
dev_err(&info->pdev->dev, "Ready timeout!!!\n");
dev_err(mtd->dev, "Ready timeout!!!\n");
return NAND_STATUS_FAIL;
}
}
......@@ -1633,7 +1633,7 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info,
ecc->strength = 16;
} else {
dev_err(&info->pdev->dev,
dev_err(info->controller.active->mtd.dev,
"ECC strength %d at page size %d is not supported\n",
strength, page_size);
return -ENODEV;
......@@ -1659,8 +1659,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
return ret;
ret = pxa3xx_nand_sensing(host);
if (ret) {
dev_info(&info->pdev->dev,
"There is no chip on cs %d!\n",
dev_info(mtd->dev, "There is no chip on cs %d!\n",
info->cs);
return ret;
}
......@@ -1676,7 +1675,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
if (!pdata->keep_config) {
ret = pxa3xx_nand_init_timings(host);
if (ret) {
dev_err(&info->pdev->dev,
dev_err(mtd->dev,
"Failed to set timings: %d\n", ret);
return ret;
}
......@@ -1720,7 +1719,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) {
chip->cmdfunc = nand_cmdfunc_extended;
} else {
dev_err(&info->pdev->dev,
dev_err(mtd->dev,
"unsupported page size on this variant\n");
return -ENODEV;
}
......@@ -1873,6 +1872,7 @@ static int pxa3xx_nand_probe_dt(struct pxa3xx_nand_info *info)
static int pxa3xx_nand_probe(struct pxa3xx_nand_info *info)
{
struct mtd_info *mtd = &info->controller.active->mtd;
struct pxa3xx_nand_platform_data *pdata;
int ret, cs, probe_success;
......@@ -1884,7 +1884,7 @@ static int pxa3xx_nand_probe(struct pxa3xx_nand_info *info)
ret = alloc_nand_resource(info);
if (ret) {
dev_err(&pdev->dev, "alloc nand resource failed\n");
dev_err(mtd->dev, "alloc nand resource failed\n");
return ret;
}
......@@ -1901,7 +1901,7 @@ static int pxa3xx_nand_probe(struct pxa3xx_nand_info *info)
info->cs = cs;
ret = pxa3xx_nand_scan(mtd);
if (ret) {
dev_info(&pdev->dev, "failed to scan nand at cs %d\n",
dev_info(mtd->dev, "failed to scan nand at cs %d\n",
cs);
continue;
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册