sunxi: display: Make lcd display clk phase configurable

While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.

This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.

This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.

The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

arch/arm/include/asm/arch-sunxi/display.h

@@ -249,9 +249,7 @@ struct sunxi_tve_reg {
 #define SUNXI_LCDC_TCON0_TIMING_V_TOTAL(n)	(((n) * 2) << 16)
 #define SUNXI_LCDC_TCON0_LVDS_INTF_BITWIDTH(n)	((n) << 26)
 #define SUNXI_LCDC_TCON0_LVDS_INTF_ENABLE	(1 << 31)
-#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE0	(0 << 28)
-#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE60	(1 << 28)
-#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE120	(2 << 28)
+#define SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE(x)	((x) << 28)
 #define SUNXI_LCDC_TCON1_CTRL_CLK_DELAY(n)	(((n) & 0x1f) << 4)
 #define SUNXI_LCDC_TCON1_CTRL_ENABLE		(1 << 31)
 #define SUNXI_LCDC_TCON1_TIMING_H_BP(n)		(((n) - 1) << 0)

board/sunxi/Kconfig

@@ -338,6 +338,13 @@ config VIDEO_LCD_MODE
 	This is in drivers/video/videomodes.c: video_get_params() format, e.g.
 	x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
 
+config VIDEO_LCD_DCLK_PHASE
+	int "LCD panel display clock phase"
+	depends on VIDEO
+	default 1
+	---help---
+	Select LCD panel display clock phase shift, range 0-3.
+
 config VIDEO_LCD_POWER
 	string "LCD panel power enable pin"
 	depends on VIDEO

configs/Ippo_q8h_v1_2_defconfig

@@ -2,6 +2,7 @@ CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
 CONFIG_FDTFILE="sun8i-a23-ippo-q8h-v1.2.dtb"
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"

configs/Ippo_q8h_v5_defconfig

@@ -2,6 +2,7 @@ CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
 CONFIG_FDTFILE="sun8i-a23-ippo-q8h-v5.dtb"
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"

configs/MSI_Primo73_defconfig

@@ -2,6 +2,7 @@ CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
 CONFIG_FDTFILE="sun7i-a20-primo73.dtb"
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:60000,le:60,ri:160,up:13,lo:12,hs:100,vs:10,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_POWER="PH8"
 CONFIG_VIDEO_LCD_BL_EN="PH7"
 CONFIG_VIDEO_LCD_BL_PWM="PB2"

drivers/video/sunxi_display.c

@@ -587,12 +587,7 @@ static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode)
 		       &lcdc->tcon0_frm_ctrl);
 	}
 
-#ifdef CONFIG_VIDEO_LCD_IF_PARALLEL
-	val = SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE0;
-#endif
-#ifdef CONFIG_VIDEO_LCD_IF_LVDS
-	val = SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE60;
-#endif
+	val = SUNXI_LCDC_TCON0_IO_POL_DCLK_PHASE(CONFIG_VIDEO_LCD_DCLK_PHASE);
 	if (!(mode->sync & FB_SYNC_HOR_HIGH_ACT))
 		val |= SUNXI_LCDC_TCON_HSYNC_MASK;
 	if (!(mode->sync & FB_SYNC_VERT_HIGH_ACT))