arm64: zynqmp: Enable booting to ATF

U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.

To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.
Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig

@@ -19,6 +19,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_FASTBOOT=y
 CONFIG_FASTBOOT_FLASH=y

configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig

@@ -20,6 +20,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_FASTBOOT=y
 CONFIG_FASTBOOT_FLASH=y

configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig

@@ -16,6 +16,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_CMD_MEMTEST=y
 CONFIG_SYS_ALT_MEMTEST=y

configs/xilinx_zynqmp_zc1751_xm019_dc5_defconfig

@@ -17,6 +17,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_CMD_MEMTEST=y
 CONFIG_SYS_ALT_MEMTEST=y

configs/xilinx_zynqmp_zcu102_rev1_0_defconfig

@@ -19,6 +19,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_FASTBOOT=y
 CONFIG_FASTBOOT_FLASH=y

configs/xilinx_zynqmp_zcu102_revA_defconfig

@@ -19,6 +19,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_FASTBOOT=y
 CONFIG_FASTBOOT_FLASH=y

configs/xilinx_zynqmp_zcu102_revB_defconfig

@@ -19,6 +19,7 @@ CONFIG_BOARD_EARLY_INIT_R=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_RAM_SUPPORT=y
 CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_ATF=y
 CONFIG_SYS_PROMPT="ZynqMP> "
 CONFIG_FASTBOOT=y
 CONFIG_FASTBOOT_FLASH=y