cosmetic: kirkwood: style fixes in kwbimage.cfg files

When diffing through the changes only the relevant changes
should be displayed.
Signed-off-by: NLuka Perkov <luka@openwrt.org>
Acked-by: NStefan Roese <sr@denx.de>

board/iomega/iconnect/kwbimage.cfg

@@ -20,7 +20,7 @@ NAND_PAGE_SIZE	0x0800
 # Configure RGMII-0 interface pad voltage to 1.8V
 DATA 0xffd100e0 0x1b1b1b9b
 
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+# Dram initalization for SINGLE x16 CL=5 @ 400MHz
 DATA 0xffd01400 0x43000c30	# DDR Configuration register
 # bit13-0:  0xc30, (3120 DDR2 clks refresh rate)
 # bit23-14: 0x0,
@@ -87,7 +87,7 @@ DATA 0xffd0141c 0x00000c52	# DDR Mode
 # bit6-4:   0x4, CL=5
 # bit7:     0x0, TestMode=0 normal
 # bit8:     0x0, DLL reset=0 normal
-# bit11-9:  0x6, auto-precharge write recovery ????????????
+# bit11-9:  0x6, auto-precharge write recovery
 # bit12:    0x0, PD must be zero
 # bit31-13: 0x0, required
 

board/raidsonic/ib62x0/kwbimage.cfg

@@ -11,7 +11,7 @@
 #
 
 # Boot Media configurations
-BOOT_FROM	nand	# change from nand to uart if building UART image
+BOOT_FROM	nand
 NAND_ECC_MODE	default
 NAND_PAGE_SIZE	0x0800
 
@@ -21,12 +21,12 @@ NAND_PAGE_SIZE	0x0800
 # Configure RGMII-0 interface pad voltage to 1.8V
 DATA 0xffd100e0 0x1b1b1b9b
 
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+# Dram initalization for SINGLE x16 CL=5 @ 400MHz
 DATA 0xffd01400 0x43000c30	# DDR Configuration register
 # bit13-0:  0xc30, (3120 DDR2 clks refresh rate)
 # bit23-14: 0x0,
-# bit24:    0x1,     enable exit self refresh mode on DDR access
-# bit25:    0x1,     required
+# bit24:    0x1,   enable exit self refresh mode on DDR access
+# bit25:    0x1,   required
 # bit29-26: 0x0,
 # bit31-30: 0x1,
 
@@ -64,10 +64,10 @@ DATA 0xffd01410 0x0000000c	# DDR Address Control
 # bit3-2:   11,  Cs0size (1Gb)
 # bit5-4:   00,  Cs1width (x8)
 # bit7-6:   11,  Cs1size (1Gb)
-# bit9-8:   00,  Cs2width (nonexistent
-# bit11-10: 00,  Cs2size  (nonexistent
-# bit13-12: 00,  Cs3width (nonexistent
-# bit15-14: 00,  Cs3size  (nonexistent
+# bit9-8:   00,  Cs2width (nonexistent)
+# bit11-10: 00,  Cs2size (nonexistent)
+# bit13-12: 00,  Cs3width (nonexistent)
+# bit15-14: 00,  Cs3size (nonexistent)
 # bit16:    0,   Cs0AddrSel
 # bit17:    0,   Cs1AddrSel
 # bit18:    0,   Cs2AddrSel
@@ -88,7 +88,7 @@ DATA 0xffd0141c 0x00000c52	# DDR Mode
 # bit6-4:   0x4, CL=5
 # bit7:     0x0, TestMode=0 normal
 # bit8:     0x0, DLL reset=0 normal
-# bit11-9:  0x6, auto-precharge write recovery ????????????
+# bit11-9:  0x6, auto-precharge write recovery
 # bit12:    0x0, PD must be zero
 # bit31-13: 0x0, required
 
@@ -148,8 +148,8 @@ DATA 0xffd0149c 0x0000e803	# CPU ODT Control
 DATA 0xffd01480 0x00000001	# DDR Initialization Control
 # bit0: 0x1, enable DDR init upon this register write
 
-DATA 0xFFD20134 0x66666666      # L2 RAM Timing 0 Register
-DATA 0xFFD20138 0x66666666      # L2 RAM Timing 1 Register
+DATA 0xffd20134 0x66666666	# L2 RAM Timing 0 Register
+DATA 0xffd20138 0x66666666	# L2 RAM Timing 1 Register
 
 # End of Header extension
 DATA 0x0 0x0