microblaze: Remove support for LL_TEMAC

LL_TEMAC is available at big endian MB and it is not properly tested
that's why the patch removes it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

board/xilinx/microblaze-generic/microblaze-generic.c

@@ -122,40 +122,5 @@ int board_eth_init(bd_t *bis)
 			txpp, rxpp);
 #endif
 
-#ifdef CONFIG_XILINX_LL_TEMAC
-# ifdef XILINX_LLTEMAC_BASEADDR
-#  ifdef XILINX_LLTEMAC_FIFO_BASEADDR
-	ret |= xilinx_ll_temac_eth_init(bis, XILINX_LLTEMAC_BASEADDR,
-			XILINX_LL_TEMAC_M_FIFO, XILINX_LLTEMAC_FIFO_BASEADDR);
-#  elif XILINX_LLTEMAC_SDMA_CTRL_BASEADDR
-#   if XILINX_LLTEMAC_SDMA_USE_DCR == 1
-	ret |= xilinx_ll_temac_eth_init(bis, XILINX_LLTEMAC_BASEADDR,
-			XILINX_LL_TEMAC_M_SDMA_DCR,
-			XILINX_LLTEMAC_SDMA_CTRL_BASEADDR);
-#   else
-	ret |= xilinx_ll_temac_eth_init(bis, XILINX_LLTEMAC_BASEADDR,
-			XILINX_LL_TEMAC_M_SDMA_PLB,
-			XILINX_LLTEMAC_SDMA_CTRL_BASEADDR);
-#   endif
-#  endif
-# endif
-# ifdef XILINX_LLTEMAC_BASEADDR1
-#  ifdef XILINX_LLTEMAC_FIFO_BASEADDR1
-	ret |= xilinx_ll_temac_eth_init(bis, XILINX_LLTEMAC_BASEADDR1,
-			XILINX_LL_TEMAC_M_FIFO, XILINX_LLTEMAC_FIFO_BASEADDR1);
-#  elif XILINX_LLTEMAC_SDMA_CTRL_BASEADDR1
-#   if XILINX_LLTEMAC_SDMA_USE_DCR == 1
-	ret |= xilinx_ll_temac_eth_init(bis, XILINX_LLTEMAC_BASEADDR1,
-			XILINX_LL_TEMAC_M_SDMA_DCR,
-			XILINX_LLTEMAC_SDMA_CTRL_BASEADDR1);
-#   else
-	ret |= xilinx_ll_temac_eth_init(bis, XILINX_LLTEMAC_BASEADDR1,
-			XILINX_LL_TEMAC_M_SDMA_PLB,
-			XILINX_LLTEMAC_SDMA_CTRL_BASEADDR1);
-#   endif
-#  endif
-# endif
-#endif
-
 	return ret;
 }

board/xilinx/microblaze-generic/xparameters.h

@@ -56,12 +56,6 @@
 /* Ethernet controller is Ethernet_MAC */
 #define XILINX_EMACLITE_BASEADDR       0x40C00000
 
-/* LL_TEMAC Ethernet controller */
-#define XILINX_LLTEMAC_BASEADDR			0x44000000
-#define XILINX_LLTEMAC_SDMA_CTRL_BASEADDR	0x42000180
-#define XILINX_LLTEMAC_BASEADDR1		0x44200000
-#define XILINX_LLTEMAC_FIFO_BASEADDR1		0x42100000
-
 /* Watchdog IP is wxi_timebase_wdt_0 */
 #define XILINX_WATCHDOG_BASEADDR	0x50000000
 #define XILINX_WATCHDOG_IRQ		1

include/configs/microblaze-generic.h

@@ -68,10 +68,6 @@
 # define CONFIG_XILINX_EMACLITE	1
 # define CONFIG_SYS_ENET
 #endif
-#if defined(XILINX_LLTEMAC_BASEADDR)
-# define CONFIG_XILINX_LL_TEMAC	1
-# define CONFIG_SYS_ENET
-#endif
 #if defined(XILINX_AXIEMAC_BASEADDR)
 # define CONFIG_XILINX_AXIEMAC	1
 # define CONFIG_SYS_ENET
@@ -355,7 +351,7 @@
 #define CONFIG_FIT		1
 #define CONFIG_OF_LIBFDT	1
 
-#if defined(CONFIG_XILINX_LL_TEMAC) || defined(CONFIG_XILINX_AXIEMAC)
+#if defined(CONFIG_XILINX_AXIEMAC)
 # define CONFIG_MII		1
 # define CONFIG_CMD_MII		1
 # define CONFIG_PHY_GIGE	1