ddr: marvell: a38x: Allow boards to specify CK_DELAY parameter

For some layouts it is necessary to adjust the CK_DELAY parameter to
successfully complete DDR training. Add the ability to specify the
CK_DELAY in the mv_ddr_topology_map.
Signed-off-by: NChris Packham <judge.packham@gmail.com>

board/alliedtelesis/x530/x530.c

@@ -66,7 +66,11 @@ static struct mv_ddr_topology_map board_topology_map = {
 	BUS_MASK_32BIT_ECC,		/* subphys mask */
 	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
 	{ {0} },			/* raw spd data */
-	{0}				/* timing parameters */
+	{0},				/* timing parameters */
+	{ {0} },			/* electrical configuration */
+	{0},				/* electrical parameters */
+	0,				/* Clock enable mask */
+	160				/* Clock delay */
 };
 
 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)

drivers/ddr/marvell/a38x/ddr3_init.c

@@ -106,8 +106,10 @@ static int mv_ddr_training_params_set(u8 dev_num)
 	struct tune_train_params params;
 	int status;
 	u32 cs_num;
+	int ck_delay;
 
 	cs_num = mv_ddr_cs_num_get();
+	ck_delay = mv_ddr_ck_delay_get();
 
 	/* NOTE: do not remove any field initilization */
 	params.ck_delay = TUNE_TRAINING_PARAMS_CK_DELAY;
@@ -131,6 +133,9 @@ static int mv_ddr_training_params_set(u8 dev_num)
 		params.g_odt_config = TUNE_TRAINING_PARAMS_ODT_CONFIG_2CS;
 	}
 
+	if (ck_delay > 0)
+		params.ck_delay = ck_delay;
+
 	status = ddr3_tip_tune_training_params(dev_num, &params);
 	if (MV_OK != status) {
 		printf("%s Training Sequence - FAILED\n", ddr_type);

drivers/ddr/marvell/a38x/ddr_topology_def.h

@@ -127,6 +127,9 @@ struct mv_ddr_topology_map {
 
 	/* Clock enable mask */
 	u32 clk_enable;
+
+	/* Clock delay */
+	int ck_delay;
 };
 
 enum mv_ddr_iface_mode {

drivers/ddr/marvell/a38x/mv_ddr_topology.c

@@ -229,6 +229,16 @@ int mv_ddr_is_ecc_ena(void)
 		return 0;
 }
 
+int mv_ddr_ck_delay_get(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	if (tm->ck_delay)
+		return tm->ck_delay;
+
+	return -1;
+}
+
 /* translate topology map definition to real memory size in bits */
 static unsigned int mem_size[] = {
 	ADDR_SIZE_512MB,

drivers/ddr/marvell/a38x/mv_ddr_topology.h

@@ -319,6 +319,7 @@ unsigned short mv_ddr_bus_bit_mask_get(void);
 unsigned int mv_ddr_if_bus_width_get(void);
 unsigned int mv_ddr_cs_num_get(void);
 int mv_ddr_is_ecc_ena(void);
+int mv_ddr_ck_delay_get(void);
 unsigned long long mv_ddr_mem_sz_per_cs_get(void);
 unsigned long long mv_ddr_mem_sz_get(void);
 unsigned int mv_ddr_rtt_nom_get(void);