dm: pci: Allow delaying auto-config until after relocation

At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.

This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

doc/device-tree-bindings/pci/x86-pci.txt

+x86 PCI DT details:
+===================
+
+Some options are available to affect how PCI operates on x86.
+
+Optional properties:
+- u-boot,skip-auto-config-until-reloc : Don't set up PCI configuration until
+	after U-Boot has relocated. Normally if PCI is used before relocation,
+	this happens before relocation also. Some platforms set up static
+	configuration in TPL/SPL to reduce code size and boot time, since these
+	phases only know about a small subset of PCI devices.
+
+Example:
+
+pci {
+	compatible = "pci-x86";
+	#address-cells = <3>;
+	#size-cells = <2>;
+	u-boot,dm-pre-reloc;
+	ranges = <0x02000000 0x0 0xc0000000 0xc0000000 0 0x10000000
+		0x42000000 0x0 0xb0000000 0xb0000000 0 0x10000000
+		0x01000000 0x0 0x1000 0x1000 0 0xefff>;
+	u-boot,skip-auto-config-until-reloc;
+};

drivers/pci/pci-uclass.c

@@ -975,12 +975,15 @@ static int pci_uclass_pre_probe(struct udevice *bus)
 	hose->bus = bus;
 	hose->first_busno = bus->seq;
 	hose->last_busno = bus->seq;
+	hose->skip_auto_config_until_reloc =
+		dev_read_bool(bus, "u-boot,skip-auto-config-until-reloc");
 
 	return 0;
 }
 
 static int pci_uclass_post_probe(struct udevice *bus)
 {
+	struct pci_controller *hose = dev_get_uclass_priv(bus);
 	int ret;
 
 	debug("%s: probing bus %d\n", __func__, bus->seq);
@@ -988,11 +991,13 @@ static int pci_uclass_post_probe(struct udevice *bus)
 	if (ret)
 		return ret;
 
-#if CONFIG_IS_ENABLED(PCI_PNP)
-	ret = pci_auto_config_devices(bus);
-	if (ret < 0)
-		return ret;
-#endif
+	if (CONFIG_IS_ENABLED(PCI_PNP) &&
+	    (!hose->skip_auto_config_until_reloc ||
+	     (gd->flags & GD_FLG_RELOC))) {
+		ret = pci_auto_config_devices(bus);
+		if (ret < 0)
+			return log_msg_ret("pci auto-config", ret);
+	}
 
 #if defined(CONFIG_X86) && defined(CONFIG_HAVE_FSP)
 	/*

include/pci.h

@@ -571,15 +571,22 @@ extern void pci_cfgfunc_config_device(struct pci_controller* hose, pci_dev_t dev
 
 #define INDIRECT_TYPE_NO_PCIE_LINK	1
 
-/*
+/**
  * Structure of a PCI controller (host bridge)
  *
  * With driver model this is dev_get_uclass_priv(bus)
+ *
+ * @skip_auto_config_until_reloc: true to avoid auto-config until U-Boot has
+ *	relocated. Normally if PCI is used before relocation, this happens
+ *	before relocation also. Some platforms set up static configuration in
+ *	TPL/SPL to reduce code size and boot time, since these phases only know
+ *	about a small subset of PCI devices. This is normally false.
  */
 struct pci_controller {
 #ifdef CONFIG_DM_PCI
 	struct udevice *bus;
 	struct udevice *ctlr;
+	bool skip_auto_config_until_reloc;
 #else
 	struct pci_controller *next;
 #endif