sunxi: clocks: Add H6 USB clock gates and resets

To enable USB support in U-Boot, add the required clock and reset gates
to the H6 clock driver. Once enabled, the generic EHCI/OCHI drivers will
pick them up from there automatically.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>

drivers/clk/sunxi/clk_h6.c

@@ -28,6 +28,22 @@ static struct ccu_clk_gate h6_gates[] = {
 	[CLK_BUS_SPI1]		= GATE(0x96c, BIT(1)),
 
 	[CLK_BUS_EMAC]		= GATE(0x97c, BIT(0)),
+
+	[CLK_USB_PHY0]		= GATE(0xa70, BIT(29)),
+	[CLK_USB_OHCI0]		= GATE(0xa70, BIT(31)),
+
+	[CLK_USB_PHY1]		= GATE(0xa74, BIT(29)),
+
+	[CLK_USB_HSIC]		= GATE(0xa7c, BIT(26)),
+	[CLK_USB_HSIC_12M]	= GATE(0xa7c, BIT(27)),
+	[CLK_USB_PHY3]		= GATE(0xa7c, BIT(29)),
+	[CLK_USB_OHCI3]		= GATE(0xa7c, BIT(31)),
+
+	[CLK_BUS_OHCI0]		= GATE(0xa8c, BIT(0)),
+	[CLK_BUS_OHCI3]		= GATE(0xa8c, BIT(3)),
+	[CLK_BUS_EHCI0]		= GATE(0xa8c, BIT(4)),
+	[CLK_BUS_EHCI3]		= GATE(0xa8c, BIT(7)),
+	[CLK_BUS_OTG]		= GATE(0xa8c, BIT(8)),
 };
 
 static struct ccu_reset h6_resets[] = {
@@ -43,6 +59,19 @@ static struct ccu_reset h6_resets[] = {
 	[RST_BUS_SPI1]		= RESET(0x96c, BIT(17)),
 
 	[RST_BUS_EMAC]		= RESET(0x97c, BIT(16)),
+
+	[RST_USB_PHY0]		= RESET(0xa70, BIT(30)),
+
+	[RST_USB_PHY1]		= RESET(0xa74, BIT(30)),
+
+	[RST_USB_HSIC]		= RESET(0xa7c, BIT(28)),
+	[RST_USB_PHY3]		= RESET(0xa7c, BIT(30)),
+
+	[RST_BUS_OHCI0]		= RESET(0xa8c, BIT(16)),
+	[RST_BUS_OHCI3]		= RESET(0xa8c, BIT(19)),
+	[RST_BUS_EHCI0]		= RESET(0xa8c, BIT(20)),
+	[RST_BUS_EHCI3]		= RESET(0xa8c, BIT(23)),
+	[RST_BUS_OTG]		= RESET(0xa8c, BIT(24)),
 };
 
 static const struct ccu_desc h6_ccu_desc = {