README.mpc85xxads

Motorola MPC8540ADS and MPC8560ADS board

Xianghua Xiao(X.Xiao@motorola.com)
Created 10/15/03
-----------------------------------------

0. Toolchain
The Binutils in ELDK toolchain 3.0 or earlier does not support the
MPC85xx chip. You need use the newest binutils-2.14.tar.bz2 from
http://ftp.gnu.org/gnu/binutils.

1. SWITCH SETTINGS & JUMPERS

1.1 First, make sure the board default setting is consistent with the document
    shipped with your board. Then apply the following changes:
    SW3[1-6]="all OFF"  (boot from 32bit flash, no boot sequence is used)
    SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
    SW11[2]='OFF for 8560, ON for 8540' (single switch to toggle 8540.8560 mode)
    SW11[7]='ON' (rev2), 'OFF' (rev1)
    SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
    SW22[1-4]="OFF OFF ON OFF"
    SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
    J1 = "Enable Prog" (Make sure your flash is programmable for development)

1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will
    have to change the system clock from the default 66Mhz to 33Mhz by
    setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
    double your platform clock(SW6) because the system clock is now only
    half of its original value.

1.3 SW6 is a very important switch, it decides your platform clock and CPU
    clock based on the on-board system clock(default 66MHz). Check the
    document along with your board for details.


2. MEMORY MAP TO WORK WITH LINUX KERNEL

2.1. For the initial bringup, we adopted a consistent memory scheme
     between u-boot and linux kernel, you can customize it based on your
     system requirements:

     0x0000_0000     0x7fff_ffff     DDR                     2G
     0x8000_0000     0x9fff_ffff     PCI MEM                 512M
     0xc000_0000     0xdfff_ffff     Rapid IO                512M
     0xe000_0000     0xe000_ffff     CCSR                    1M
     0xe200_0000     0xe2ff_ffff     PCI IO                  16M
     0xf000_0000     0xf7ff_ffff     SDRAM                   128M
     0xf800_0000     0xf80f_ffff     BCSR                    1M
     0xff00_0000     0xffff_ffff     FLASH (boot bank)       16M

2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You
    can download them from linuxppc-2.4 public source. Please make sure the
    kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two
    default configuration files as your starting points to configure the
    kernel:
	arch/ppc/configs/mpc8540_ads_defconfig
	arch/ppc/configs/mpc8560_ads_defconfig


3. DEFINITIONS AND COMPILATION

3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/
    configs/MPC8560ADS.h
    CONFIG_BOOKE            BOOKE(e.g. Motorola MPC85xx, IBM 440, etc)
    CONFIG_E500             BOOKE e500 family(Motorola)
    CONFIG_MPC85xx          MPC8540,MPC8560 and their derivatives
    CONFIG_MPC8540          MPC8540 specific
    CONFIG_MPC8560          MPC8560 specific
    CONFIG_MPC8540ADS       MPC8540ADS board specific
    CONFIG_MPC8560ADS       MPC8560ADS board specific
    CONFIG_TSEC_ENET        Use on-chip 10/100/1000 ethernet for networking
    CONFIG_SPD_EEPROM       Use SPD EEPROM for DDR auto configuration, you can also
			    manual config the DDR after undef this definition.
    CONFIG_DDR_ECC          only for ECC DDR module
    CONFIG_DDR_DLL          DLL fix on some ADS boards needed for more stability.
    CONFIG_RAM_AS_FLASH     after define this, you can load U-Boot into localbus
			    SDRAM and treat localbus SDRAM as a flash. We use this
			    memory based U-Boot before flash is working while Metrowerks
			    and Windriver are still working on their flash/JTAG tools.
			    if you can program the flash directly, undef this.
    Other than the above definitions, the rest in the config files are straightforward.

3.2 Compilation
   export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell)
   cd u-boot
   make distclean
   make MPC8560ADS_config (or make MPC8540ADS_config)
   make


4.  Notes:

4.1 When connecting with kermit, the following commands must be present.in
   your .kermrc file. These are especially important when booting as
   MPC8560, as the serial console will not work without them:

set speed 115200
set carrier-watch off
set handshake none
set flow-control none
robust

4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
   happens, you can try the following steps to make network work:
   MPC8560ADS>tftp 1000000 pImage
   (if it hangs, use Ctrl-C to quit)
   MPC8560ADS>nm fdf24524
   >0
   >1
   >. (to quit this memory operation)
   MPC8560ADS>tftp 1000000 pImage

4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot
   1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.

4.4 Reflash U-boot Image using U-boot

    => tftp 0 u-boot.bin
    => protect off fff80000 ffffffff
    => erase fff80000 ffffffff
    => cp.b 0 fff80000 80000


5. Screen dump:

5.1 MPC8540ADS board
U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33)

Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010
Board: Motorola MPC8540ADS Board
	CPU: 792 MHz
	CCB: 264 MHz
	DDR: 132 MHz
	LBC: 66 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C:   ready
DRAM:  DDR module detected, total size:128MB.
128 MB
FLASH: 16 MB
L2 cache enabled: 256KB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   MOTOROLA ETHERNE
Hit any key to stop autoboot:  0
MPC8540ADS=> fli

Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
  Size: 16 MB in 64 Sectors
  Sector Start Addresses:
    FF000000      FF040000      FF080000      FF0C0000      FF100000
    FF140000      FF180000      FF1C0000      FF200000      FF240000
    FF280000      FF2C0000      FF300000      FF340000      FF380000
    FF3C0000      FF400000      FF440000      FF480000      FF4C0000
    FF500000      FF540000      FF580000      FF5C0000      FF600000
    FF640000      FF680000      FF6C0000      FF700000      FF740000
    FF780000      FF7C0000      FF800000      FF840000      FF880000
    FF8C0000      FF900000      FF940000      FF980000      FF9C0000
    FFA00000      FFA40000      FFA80000      FFAC0000      FFB00000
    FFB40000      FFB80000      FFBC0000      FFC00000      FFC40000
    FFC80000      FFCC0000      FFD00000      FFD40000      FFD80000
    FFDC0000      FFE00000      FFE40000      FFE80000      FFEC0000
    FFF00000      FFF40000      FFF80000 (RO) FFFC0000 (RO)
MPC8540ADS=> imi ff000000

## Checking Image at ff000000 ...
   Image Name:   Linux-2.4.21-rc5
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    800594 Bytes = 781.8 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
MPC8540ADS=> bdinfo
memstart    = 0x00000000
memsize     = 0x08000000
flashstart  = 0xFF000000
flashsize   = 0x01000000
flashoffset = 0x00000000
sramstart   = 0x00000000
sramsize    = 0x00000000
immr_base   = 0xFDF00000
bootflags   = 0x40003F80
intfreq     =    792 MHz
busfreq     =    264 MHz
ethaddr     = 00:01:AF:07:9B:8A
eth1addr    = 00:01:AF:07:9B:8B
eth2addr    = 00:01:AF:07:9B:8C
IP addr     = 10.82.0.105
baudrate    = 115200 bps
MPC8540ADS=> printenv
bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200
bootcmd=bootm 0xff300000 0xff700000
bootdelay=3
baudrate=115200
loads_echo=1
ethaddr=00:01:af:07:9b:8a
eth1addr=00:01:af:07:9b:8b
eth2addr=00:01:af:07:9b:8c
ipaddr=10.82.0.105
serverip=163.12.64.52
rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
gatewayip=10.82.1.254
netmask=255.255.254.0
hostname=MPC8560ADS_PILOT_003
bootfile=pImage
stdin=serial
stdout=serial
stderr=serial

Environment size: 560/8188 bytes
MPC8540ADS=> bootm ff000000
## Booting image at ff000000 ...
   Image Name:   Linux-2.4.21-rc5
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    800594 Bytes = 781.8 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
mpc85xx_init(): exit
id mach(): done
MMU:enter
Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exit
Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #1 Wed Oct 15 09:05:42 CDT 2003
setup_arch: enter
setup_arch: bootmem
mpc85xx_setup_arch
Host Bridge Vendor ID = 1057
Host Bridge Device ID = 3
Host Bridge header = 0
arch: exit
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200
openpic: enter
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000
openpic: timer
openpic: external
openpic: spurious
openpic: exit
time_init: decrementer frequency = 33.000000 MHz
Calibrating delay loop... 226.09 BogoMIPS
Memory: 127488k available (1344k kernel code, 448k data, 248k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware

Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xfdf04500 (irq = 90) is a 16550A
ttyS01 at 0xfdf04600 (irq = 0) is a 16550A
eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a:
eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b:
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.0.43-k1
Copyright (c) 1999-2003 Intel Corporation.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
IP-Config: Complete:
      device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254,
     host=mpc8540ads-003, domain=, nis-domain=(none),
     bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 163.12.64.52
Looking up port of RPC 100005/1 on 163.12.64.52
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 248k init
INIT: version 2.78 booting
Activating swap...
Checking all file systems...
Parallelizing fsck version 1.22 (22-Jun-2001)
Mounting local filesystems...
nothing was mounted
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: rp_filter.
Disable TCP/IP Explicit Congestion Notification: done.
Configuring network interfaces: done.
Starting portmap daemon: portmap.
Cleaning: /tmp /var/lock /var/run.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd klogd.
Starting internet superserver: inetd.

mpc8540ads-003 login: root
Last login: Thu Jan  1 00:00:07 1970 on console
Linux mpc8540ads-003 2.4.21-rc5 #1 Wed Oct 15 09:05:42 CDT 2003 ppc unknown

root@mpc8540ads-003:~# ls
21142.o     aa	     e100.o	 hello.o      mii.o    timer.o
root@mpc8540ads-003:~# /sbin/ifconfig
eth0      Link encap:Ethernet  HWaddr 00:01:AF:07:9B:8A
	  inet addr:10.82.0.105  Bcast:10.82.1.255  Mask:255.255.254.0
	  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
	  RX packets:4576 errors:0 dropped:0 overruns:0 frame:0
	  TX packets:2587 errors:0 dropped:0 overruns:0 carrier:0
	  collisions:0 txqueuelen:100
	  RX bytes:4457023 (4.2 Mb)  TX bytes:437770 (427.5 Kb)
	  Base address:0x4000

lo        Link encap:Local Loopback
	  inet addr:127.0.0.1  Mask:255.0.0.0
	  UP LOOPBACK RUNNING  MTU:16436  Metric:1
	  RX packets:4 errors:0 dropped:0 overruns:0 frame:0
	  TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
	  collisions:0 txqueuelen:0
	  RX bytes:296 (296.0 b)  TX bytes:296 (296.0 b)

root@mpc8540ads-003:~# ping 163.12.64.52
PING 163.12.64.52 (163.12.64.52): 56 data bytes
64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.2 ms
64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms
64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms

--- 163.12.64.52 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.1/0.1/0.2 ms
root@mpc8540ads-003:~#

5.2 MPC8560ADS board
U-Boot 1.0.0-pre (Oct 15 2003 - 13:42:04)

Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010
Board: Motorola MPC8560ADS Board
	CPU: 792 MHz
	CCB: 264 MHz
	DDR: 132 MHz
	LBC: 66 MHz
	CPM: 264 Mhz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C:   ready
DRAM:  DDR module detected, total size:128MB.
128 MB
FLASH: 16 MB
L2 cache enabled: 256KB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   MOTOROLA ETHERNE
Hit any key to stop autoboot:  3
MPC8560ADS=> bdinfo
memstart    = 0x00000000
memsize     = 0x08000000
flashstart  = 0xFF000000
flashsize   = 0x01000000
flashoffset = 0x00000000
sramstart   = 0x00000000
sramsize    = 0x00000000
immr_base   = 0xFDF00000
bootflags   = 0x00000000
vco         =    528 MHz
sccfreq     =    132 MHz
brgfreq     =    132 MHz
intfreq     =    792 MHz
cpmfreq     =    264 MHz
busfreq     =    264 MHz
ethaddr     = 00:01:AF:07:9B:8A
eth1addr    = 00:01:AF:07:9B:8B
eth2addr    = 00:01:AF:07:9B:8C
IP addr     = 10.82.0.105
baudrate    = 115200 bps
MPC8560ADS=> printenv
bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200
bootcmd=bootm 0xff400000 0xff700000
bootdelay=3
baudrate=115200
loads_echo=1
ethaddr=00:01:af:07:9b:8a
eth1addr=00:01:af:07:9b:8b
eth2addr=00:01:af:07:9b:8c
ipaddr=10.82.0.105
serverip=163.12.64.52
rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
gatewayip=10.82.1.254
netmask=255.255.254.0
hostname=MPC8560ADS_PILOT_003
bootfile=pImage
stdin=serial
stdout=serial
stderr=serial

Environment size: 560/8188 bytes
MPC8560ADS=> fli

Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
  Size: 16 MB in 64 Sectors
  Sector Start Addresses:
    FF000000      FF040000      FF080000      FF0C0000      FF100000
    FF140000      FF180000      FF1C0000      FF200000      FF240000
    FF280000      FF2C0000      FF300000      FF340000      FF380000
    FF3C0000      FF400000      FF440000      FF480000      FF4C0000
    FF500000      FF540000      FF580000      FF5C0000      FF600000
    FF640000      FF680000      FF6C0000      FF700000      FF740000
    FF780000      FF7C0000      FF800000      FF840000      FF880000
    FF8C0000      FF900000      FF940000      FF980000      FF9C0000
    FFA00000      FFA40000      FFA80000      FFAC0000      FFB00000
    FFB40000      FFB80000      FFBC0000      FFC00000      FFC40000
    FFC80000      FFCC0000      FFD00000      FFD40000      FFD80000
    FFDC0000      FFE00000      FFE40000      FFE80000      FFEC0000
    FFF00000      FFF40000      FFF80000 (RO) FFFC0000 (RO)
MPC8560ADS=> imi ff100000

## Checking Image at ff100000 ...
   Image Name:   Linux-2.4.21-rc5
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    755361 Bytes = 737.7 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
MPC8560ADS=> tftp 1000000 pImage.dracom.public
TFTP from server 163.12.64.52; our IP address is 10.82.0.105; sending through gateway 10.82.1.254
Filename 'pImage.dracom.public'.
Load address: 0x1000000
Loading: *#################################################################
	 #################################################################
	 ##################
done
Bytes transferred = 755425 (b86e1 hex)
MPC8560ADS=> bootm ff100000
## Booting image at ff100000 ...
   Image Name:   Linux-2.4.21-rc5
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    755361 Bytes = 737.7 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
mpc85xx_init(): exit
id mach(): done
MMU:enter
Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exit
Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #2 Wed Oct 15 09:13:46 CDT 2003
setup_arch: enter
setup_arch: bootmem
mpc85xx_setup_arch
Host Bridge Vendor ID = 1057
Host Bridge Device ID = 3
Host Bridge header = 0
arch: exit
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200
openpic: enter
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000
openpic: timer
openpic: external
openpic: spurious
openpic: exit
time_init: decrementer frequency = 33.000000 MHz
Calibrating delay loop... 226.09 BogoMIPS
Memory: 127624k available (1276k kernel code, 384k data, 236k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware

Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
CPM UART driver version 0.01
ttyS0 on SCC1 at 0x8000, BRG1
UART interrupt installed(40)
pty: 256 Unix98 ptys configured
eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a:
eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b:
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.0.43-k1
Copyright (c) 1999-2003 Intel Corporation.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
IP-Config: Complete:
      device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254,
     host=mpc8560ads-003, domain=, nis-domain=(none),
     bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 163.12.64.52
Looking up port of RPC 100005/1 on 163.12.64.52
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 236k init
INIT: version 2.78 booting
Activating swap...
Checking all file systems...
Parallelizing fsck version 1.22 (22-Jun-2001)
Mounting local filesystems...
nothing was mounted
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: FAILED
Configuring network interfaces: done.
Starting portmap daemon: portmap.
Cleaning: /tmp /var/lock /var/run.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd klogd.
Starting internet superserver: inetd.

mpc8560ads-003 login: root
Last login: Thu Jan  1 00:00:05 1970 on console
Linux mpc8560ads-003 2.4.21-rc5 #2 Wed Oct 15 09:13:46 CDT 2003 ppc unknown

root@mpc8560ads-003:~# ls
21142.o     aa	     e100.o	 hello.o      mii.o    timer.o
root@mpc8560ads-003:~# cd /
root@mpc8560ads-003:/# ls
bin  boot  dev	etc  home  lib	mnt  opt  proc	root  sbin  tmp  usr  var
root@mpc8560ads-003:/# /sbin/ifconfig
eth0      Link encap:Ethernet  HWaddr 00:01:AF:07:9B:8A
	  inet addr:10.82.0.105  Bcast:10.82.1.255  Mask:255.255.254.0
	  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
	  RX packets:4608 errors:0 dropped:0 overruns:0 frame:0
	  TX packets:2610 errors:0 dropped:0 overruns:0 carrier:0
	  collisions:0 txqueuelen:100
	  RX bytes:4465943 (4.2 Mb)  TX bytes:440944 (430.6 Kb)
	  Base address:0x4000

lo        Link encap:Local Loopback
	  inet addr:127.0.0.1  Mask:255.0.0.0
	  UP LOOPBACK RUNNING  MTU:16436  Metric:1
	  RX packets:4 errors:0 dropped:0 overruns:0 frame:0
	  TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
	  collisions:0 txqueuelen:0
	  RX bytes:296 (296.0 b)  TX bytes:296 (296.0 b)

root@mpc8560ads-003:/# ping 163.12.64.52
PING 163.12.64.52 (163.12.64.52): 56 data bytes
64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.1 ms
64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms
64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms

--- 163.12.64.52 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.1/0.1/0.1 ms
root@mpc8560ads-003:/#