no idea why these 4 are permuted and the rest are standard/generic

...and still be valid in #if directives.

right now it's questionable whether this change is an improvement or
not, but if we later want to support priority inheritance mutexes, it
will be important to have the code paths unified like this to avoid
major code duplication.

this is valid for error-checking mutexes; otherwise it invokes UB and
would be justified in crashing.

this simplifies the code paths slightly, but perhaps what's nicer is
that it makes recursive mutexes fully reentrant, i.e. locking and
unlocking from a signal handler works even if the interrupted code was
in the middle of locking or unlocking.

a reader unlocking the lock need only wake one waiter (necessarily a
writer, but a writer unlocking the lock must wake all waiters
(necessarily readers). if it only wakes one, the remainder can remain
blocked indefinitely, or at least until the first reader unlocks (in
which case the whole lock becomes serialized and behaves as a mutex
rather than a read lock).

mildly tested, seems to work

passing null pointer for %s is UB but lots of broken programs do it anyway

there is no need to send a wake when the lock count does not hit zero,
but when it does, all waiters must be woken (since all with the same
sign are eligible to obtain the lock).

seeking back can be performed by the caller, but if the caller doesn't
expect it, it will result in an infinite loop of failures.

eliminate the sequence number field and instead use the counter as the
futex because of the way the lock is held, sequence numbers are
completely useless, and this frees up a field in the barrier structure
to be used as a waiter count for the count futex, which lets us avoid
some syscalls in the best case.

as of now, self-synchronized destruction and unmapping should be fully
safe. before any thread can return from the barrier, all threads in
the barrier have obtained the vm lock, and each holds a shared lock on
the barrier. the barrier memory is not inspected after the shared lock
count reaches 0, nor after the vm lock is released.

i think this works, but it can be simplified. (next step)

the vm lock only waits for threads in the same process exiting.
actually this fix is not enough, but it's a start...

it was assuming the result of the condition it was supposed to be
checking for, i.e. that the thread ptr had already been initialized by
pthread_mutex_lock. use the slower call to be safe.

we're not required to check this except for error-checking mutexes,
but it doesn't hurt. the new test is actually simpler/lighter, and it
also eliminates the need to later check that pthread_mutex_unlock
succeeds.

when used with error-checking mutexes, pthread_cond_wait is required
to fail with EPERM if the mutex is not locked by the caller.
previously we relied on pthread_mutex_unlock to generate the error,
but this is not valid, since in the case of such invalid usage the
internal state of the cond variable has already been potentially
corrupted (due to access outside the control of the mutex). thus, we
have to check first.

i set the return value but then never used it... oops!

not sure if this is correct/ideal. it needs further attention.

this implementation is rather heavy-weight, but it's the first
solution i've found that's actually correct. all waiters actually wait
twice at the barrier so that they can synchronize exit, and they hold
a "vm lock" that prevents changes to virtual memory mappings (and
blocks pthread_barrier_destroy) until all waiters are finished
inspecting the barrier.

thus, it is safe for any thread to destroy and/or unmap the barrier's
memory as soon as pthread_barrier_wait returns, without further
synchronization.

mmap returns MAP_FAILED not 0 because some idiot thought the ability
to mmap the null pointer page would be a good idea...

issue reported by nsz, but it's actually not just pedantic. the
functions can take input of any arithmetic type, including floating
point, and the behavior needs to be as if the conversion implicit in
the function call took place.

lock out new waiters during the broadcast. otherwise the wait count
added to the mutex might be lower than the actual number of waiters
moved, and wakeups may be lost.

this issue could also be solved by temporarily setting the mutex
waiter count higher than any possible real count, then relying on the
kernel to tell us how many waiters were requeued, and updating the
counts afterwards. however the logic is more complex, and i don't
really trust the kernel. the solution here is also nice in that it
replaces some atomic cas loops with simple non-atomic ops under lock.

due to moving waiters from the cond var to the mutex in bcast, these
waiters upon wakeup would steal slots in the count from newer waiters
that had not yet been signaled, preventing the signal function from
taking any action.

to solve the problem, we simply use two separate waiter counts, and so
that the original "total" waiters count is undisturbed by broadcast
and still available for signal.

the changes to syscall_ret are mostly no-ops in the generated code,
just cleanup of type issues and removal of some implementation-defined
behavior. the one exception is the change in the comparison value,
which is fixed so that 0xf...f000 (which in principle could be a valid
return value for mmap, although probably never in reality) is not
treated as an error return.

testing revealed that the old implementation, while correct, was
giving way too many spurious wakeups due to races changing the value
of the condition futex. in a test program with 5 threads receiving
broadcast signals, the number of returns from pthread_cond_wait was
roughly 3 times what it should have been (2 spurious wakeups for every
legitimate wakeup). moreover, the magnitude of this effect seems to
grow with the number of threads.

the old implementation may also have had some nasty race conditions
with reuse of the cond var with a new mutex.

the new implementation is based on incrementing a sequence number with
each signal event. this sequence number has nothing to do with the
number of threads intended to be woken; it's only used to provide a
value for the futex wait to avoid deadlock. in theory there is a
danger of race conditions due to the value wrapping around after 2^32
signals. it would be nice to eliminate that, if there's a way.

testing showed no spurious wakeups (though they are of course
possible) with the new implementation, as well as slightly improved
performance.

using swap has a race condition: the waiters must be added to the
mutex waiter count *before* they are taken off the cond var waiter
count, or wake events can be lost.