To be able to use mmc_send_tuning() prior the struct mmc_card has been
allocated, let's convert it to take the struct mmc_host* as parameter
instead.
Suggested-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NDong Aisheng <b29396@freescale.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>

According to the SD card spec, Add a manual tuning command function
for SDR104/HS200.
Sending command 19 or command 21 to read data and compare with the
tunning block pattern.

This patch will help to decrease some platform private codes in SDHCI
platform_execute_tuning() callbacks.
Signed-off-by: NMinda Chen <Minda.Chen@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: NAddy Ke <addy.ke@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC core already has support for HS400.  Add HS400
support to SDHCI driver.  The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard.  However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected.  To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.

Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution.  As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V.  Do the same for 1.2V HS400 mode.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: NPrabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: NVincent Wan <vincent.wan@amd.com>
Signed-off-by: NWan Zongshun <mcuos.com@gmail.com>
Signed-off-by: NArindam Nath <arindam.nath@amd.com>
Tested-by: NVikram B <vikram.b@amd.com>
Tested-by: NRaghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add 64-bit ADMA support including:
	- add 64-bit ADMA descriptor
	- add SDHCI_USE_64_BIT_DMA flag
	- set upper 32-bits of DMA addresses
	- ability to select 64-bit ADMA
	- ability to use 64-bit ADMA sizes and alignment
	- display "ADMA 64-bit" when host is added

It is assumed that a 64-bit capable device has set a 64-bit DMA mask
and *must* do 64-bit DMA.  A driver has the opportunity to change
that during the first call to ->enable_dma().  Similarly
SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
implement.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for 64-bit ADMA, parameterize ADMA sizes
and alignment.  64-bit ADMA has a larger descriptor
because it contains a 64-bit address instead of a 32-bit
address.  Also data must be 8-byte aligned instead
of 4-byte aligned.  Consequently, sdhci_host members
are added for descriptor, table, and buffer sizes
and alignment.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It is kernel-style to use 'void *' for anonymous data.
This is being applied to the ADMA bounce buffer which
contains unaligned bytes, and to the ADMA descriptor
table which will contain 32-bit ADMA descriptors
or 64-bit ADMA descriptors when support is added.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for 64-bit ADMA, rename adma_desc to
adma_table.  That is because members will be added
for descriptor size and table size, so using adma_desc
(which is the table) is confusing.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Previous patches has replaced the calls to mmc_send_ext_csd() into
mmc_get_ext_csd(), thus mmc_send_ext_csd() has become redundant. Let's
remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted.  However, this code was old and crufty and
should be removed.  Some evidence that it's really not needed:

1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
   using the built-in card detect mechanism.  The 'cd-gpio' code
   doesn't run any of the crufty old code but yet still works.

2. While looking at this, I realized that my old change (369ac861 mmc:
   dw_mmc: don't queue up a card detect at slot startup) actually
   castrated the old code a little bit already and nobody noticed.
   Specifically "last_detect_state" was left as 0 at bootup.  That
   means that on the first card removal none of the crufty code ran.

3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
   while ejecting and inserting an SD Card and the world doesn't
   explode.

If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".

Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup.  That
was actually causing a real bug.  The card detect workqueue was
running while the system was trying to enumerate the card.  The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration.  The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: Nalim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: NGwendal Grignou <gwendal@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In most of the cases mmc_get|set_drvdata() didn't simplify code, which
should be the primary reason for such macros.

Let's remove them and convert to the common device_driver macros,
dev_set|get_drvdata() instead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The struct mmc_driver adds an extra layer on top of the struct
device_driver. That would be fine, if there were a good reason, but
that's not the case.

Let's simplify code by converting to the common struct device_driver
instead and thus also removing superfluous overhead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The macro is only used by the mmc core, so let's move it in there.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a quirk for a host controller that always sets
a Transfer Complete interrupt status for the stop
command even when a busy response is not indicated.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

commit 98e90de9
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.

It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: NJavier Martinez Canillas <javier@dowhile0.org>
Tested-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.

For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Replace ext_csd "enhanced_area_en" attribute by
 "partition_setting_completed". It was used whether or
 not enhanced user area is defined and without checks of
 EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: NGrégory Soutadé <gsoutade@neotion.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now, mmc framework uses multi_io_quirk
for I/O HW bug workaround.
MMC_CAP2_NO_MULTI_READ flag is no longer needed
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.

There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.

In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.

"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."

This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.

Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>

Changes since v1:
 Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
 and Tested if issue is fixed again.
Signed-off-by: NHankyung Yu <hankyung.yu@lge.com>
Signed-off-by: NChanho Min <chanho.min@lge.com>
Tested-by: NYoussef TRIKI <youssef.triki@st.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For UHS cards we need the ability to switch voltages from 3.3V to
1.8V.  Add support to the dw_mmc driver to handle this.  Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.

Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.

This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eMMC card can support up to 7 physical partitions, including 2 boot,
1 RPMB and 4 GPs. Change MMC_NUM_PHY_PARTITION from 6 to 7, which is
the correct value.
Signed-off-by: NYi Sun <yi.y.sun@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Slot quirks "disable-wp" is deprecated.
Instead, use the host quirk "disable-wp".
(Because the slot-node is removed in dt-file.)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure.  Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.

This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: NTim Kryger <tim.kryger@gmail.com>
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Track whether preset mode is currently enabled in hardware, and use that
when making decisions elsewhere in the code rather than reading the
register and checking the bit.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Rather than reading back the timing information from the registers,
cache it locally.  This allows implementations to translate the UHS
timing by overriding the set_uhs_signaling() method as required
without also having to emulate the SDHCI_HOST_CONTROL2 register.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset.  Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

There's no requirement to have the card tasklet separate now that we
have a threaded interrupt handler, so kill this and move the called
code into the threaded part of the handler.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>