* Add IDE_HFLAG_NO_DSC host flag for hosts that doesn't support DSC overlap.

* Set it in aec62xx (for ATP850UF only) and hpt34x host drivers.

* Convert ide-tape device driver to check for IDE_HFLAG_NO_DSC flag.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().

* Factor out code for forcing host out of "simplex" mode from
  ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.

* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
  amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
  serverworks (for CSB5) host drivers.

* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
  instead of checking dev->device (BTW the code was buggy because it didn't
  check for dev->vendor, luckily none of these PCI Device IDs was used by
  some other vendor for PCI IDE controller).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_dump_identify() debug helper for dumping raw identify data in
  the hdparm friendly format (== the identify data can be extracted from
  dmesg output and passed to hdparm --Istdin).

* Dump identify data in ide-probe.c::do_identify() if DEBUG is enabled.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After commit 7267c337 
wait_drive_not_busy() can become static again.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

- ide_scan_pcibus() can become static
- instead of ide_scan_pci() we can use ide_scan_pcibus() directly
  in module_init()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

Switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
and make ide_wait_cmd() static.

There should be no functionality changes caused by this patch.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use wait_drive_not_busy() in drive_cmd_intr().

v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests.  Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set.  Also,
ide_dma_intr() is modified to use task_end_request().

Enables TASKFILE ioctls to get valid register outputs on
successful completion.

Bart:
- ported it over recent IDE changes
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.

* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.

* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit.  It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().

This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.

Bart:
- ported it over recent IDE changes
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
  results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
  (including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
  x86 machines using user-space solutions or dm-byteswap should result in
  much better performance because DMA can be used)

For previous discussions please see:

http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.html
http://lkml.org/lkml/2004/2/28/111

[ I have dm-byteswap device mapper target if somebody is interested
  (patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
  file for probing PCI host drivers registered with IDE core (special case
  for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
  the ordering in which all IDE host drivers are probed when IDE is built-in
  during link time.

* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
  specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
  arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).

* Move probing of ide-cris (cris arch specific) host driver before cmd640
  (x86 arch specific).

* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
  on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
  (h8300 arch specific).

* Add "probe_vlb" kernel parameter to cmd640 host driver and update
  Documentation/ide.txt accordingly.

* Make IDE_ARM config option visible so it can also be disabled if needed.

* Remove bogus comment from ide.c while at it.

v2:
* Fix two issues spotted by Sergei:
  - replace ENOMEM error value by ENOENT in ide-h8300 host driver
  - fix MODULE_PARM_DESC() in cmd640 host driver

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename init_hwif_data() to ide_init_port_data() and export it.

* For all users of ide_register_hw() with 'initializing' argument set
  hwif->present and hwif->hold are always zero so convert these host
  drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
  instead (also no need for init_hwif_default() call since the setup
  done by it gets over-ridden by ide_init_port_hw() call).

* Drop 'initializing' argument from ide_register_hw().

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_init_port_hw() helper.

* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
  and use ide_init_port_hw().

* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
  and use ide_init_port_hw().

* sgiioc4.c: use ide_init_port_hw().

* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
  setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
  in pmac_ide_setup_device().

This patch is a preparation for the future changes in the IDE probing code.

There should be no functionality changes caused by this patch.

Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix build break of powerpc holly_defconfig:

In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)

There's no need to have a sized array in the prototype, might as well
turn it into a pointer.

It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_device_add() to ide_device_add_all() and make it accept
  'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.

* Add ide_device_add() wrapper for ide_device_add_all().

* Convert ide_generic_init() to use ide_device_add_all().

* Remove no longer needed ideprobe_init().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Assign drive->quirk_list in ->quirkproc implementations:
  - hpt366.c::hpt3xx_quirkproc()
  - pdc202xx_new.c::pdcnew_quirkproc()
  - pdc202xx_old.c::pdc202xx_quirkproc()

* Make ->quirkproc void.

* Move calling ->quirkproc from do_identify() to probe_hwif().

* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.

* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
  no longer needed drive->present check from is_dev_seagate_sata().

* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
  as an argument.  Then convert ide_register_hw() to accept 'quirkproc'
  argument instead of 'fixup' one.

* Remove no longer needed ->fixup method.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_dma_off_quietly() and __ide_dma_on() always available.

* Drop "__" prefix from __ide_dma_on().

* Check for presence of ->dma_host_on instead of ->ide_dma_on.

* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
  to use ide_dma_on() and ide_dma_off_quietly() instead.

* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
  from ide_hwif_t.

* Make ide_dma_on() void.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix SWDMA/MWDMA masks in cy82c693_chipset.

* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
  check whether the DMA should be enabled even if ide_max_dma_mode()
  fails.

* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
  and remove no longer needed cy82c693_ide_dma_on().  Then set
  IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
  cy82c693_chipset.

* Bump driver version.

As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
  what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().

* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
  (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
  serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
  methods in host drivers that don't (IDE core code guarantees that
  ->set_dma_mode will be called only for modes which are present
  in SWDMA/MWDMA/UDMA masks).

While at it:

* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
  hpt34x/hpt366/pdc202xx_old/serverworks host driver.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The maximum value used currently for 'extra' field in struct ide_port_info
is 240.

Make 'extra' u8 so it packs nicely together with enablebits[] and 'chipset'
fields (ide_pci_enablebit_t is 3 bytes and hwif_chipset_t is 1 byte).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Export ide_get_lba_addr().

* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().

* Remove incorrect comment from idedisk_read_native_max_address()
  (noticed by Sergei).

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out code reading taskfile registers from ide_end_drive_cmd()
  to the new ide_tf_read() helper.

* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
  particular IDE taskfile register in ide_tf_read().

* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.

* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.

* Factor out code getting sector address from ide_dump_ata_status()
  to the new ide_dump_sector() function.

* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().

* Remove no longer needed ide_read_24().

The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_DMA_PIO_FALLBACK taskfile flag to indicate the need
  to skip loading taskfile registers in do_rw_taskfile().

* Export do_rw_taskfile().

* Convert __ide_do_rw_disk() to use do_rw_taskfile().

* Unexport ide_tf_load().

* Unexport {pre_task_out,task_in}_intr() and make it static.

* Remove incorrect comment about do_rw_taskfile() from <linux/ide.h>.

There should be no functionality changes caused by this patch.

v2:
* Add missing blk_fs_request() check to task_dma_ok() (for VDMA).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
  which require custom handlers.  Check the flag in do_rw_taskfile() and set
  handler accordingly.

* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
  ide_tf_set_{specify,restore,setmult}_cmd().

* Make {set_geometry,recal,set_multmode}_intr() static.

* Remove no longer needed 'handler' field from ide_task_t.

v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->data_phase to set ->handler in do_rw_taskfile() instead of
  setting ->handler in callers of ide_raw_taskfile()/do_rw_taskfile().

* Unexport task_no_data_intr() and make it static.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use task->data_phase in do_rw_taskfile() to decide what to do.

* task->prehandler is only used by TASKFILE[_MULTI]_OUT so just
  use pre_task_out_intr() directly and remove no longer needed
  'prehandler' field from ide_task_t.

* Remove no longer needed ide_pre_handler_t type.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

task->data_phase == TASKFILE_MULTI_{IN,OUT} vs drive->mult_count == 0
check is needed also for ide_taskfile_ioctl() requests that don't have
IDE_TFLAG_FLAGGED taskfile flag set.

Cc: Tejun Heo <htejun@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_IN_DATA taskfile flag to indicate the need of reading
  IDE_DATA_REG in ide_end_drive_cmd().

  Set the new flag in ide_taskfile_ioctl() if ->in_flags.b.data is set.

* Add IDE_TFLAG_FLAGGED_SET_IN_FLAGS taskfile flag to indicate the
  need of modifying ->in_flags in ide_taskfile_ioctl().

  Set the new flag in flagged_taskfile() and move the code modifying
  ->tf_in_flags to ide_taskfile_ioctl().

  While at it remove the bogus comment: ->tf_in_flags (except .b.data)
  have no effect on selection of registers to read.

* Remove no longer needed 'tf_in_flags' field from ide_task_t.

As the result we finally have the internals of HDIO_DRIVE_TASKFILE ioctl
separated from the core IDE code.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'data_buf' and 'nsect' variables in ide_taskfile_ioctl()
  to cache data buffer pointer and number of sectors to transfer
  (this allows us to have only one ide_diag_taskfile() call).

* Add IDE_TFLAG_WRITE taskfile flag and use it to check whether
  the REQ_RW request flag should be set.

* Move ->command_type handling from ide_diag_taskfile() to
  ide_taskfile_ioctl() and use ->req_cmd instead of ->command_type.

* Add 'nsect' parameter to ide_raw_taskfile().

* Merge ide_diag_taskfile() into ide_raw_taskfile().

* Initialize ->data_phase explicitly in idedisk_prepare_flush(),
  ide_start_power_step() and ide_disk_special().

* Remove no longer needed 'command_type' field from ide_task_t.

* Add #ifndef/#endif __KERNEL__ to <linux/hdreg.h> around no
  longer used by kernel IDE_DRIVE_TASK_* and TASKFILE_* defines.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Given that:

* hpt366.c::hpt3xx_intrproc() is the only user of hwif->intrproc

* hpt366.c::hpt3xx_quirkproc() sets drive->quirk_list to 1 for quirky drives
  which is a value unique to hpt366 host driver

we can remove hwif->intproc and just check for drive->quirk_list == 1
in ide_do_request().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_pktcmd_tf_load() helper and convert ATAPI device drivers to use it.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove atapi_ireason_t.

While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)

v2:
* v1 had CD and IO bits reversed in many places.

* Use CD and IO defines from <linux/hdreg.h>.

v3:
* Fix incorrect "(ireason & IO) == test_bit()". (Noticed by Sergei)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ata_nsector_t, ata_data_t (unused) and atapi_bcount_t.

While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>