With this commit all sparc64 header files are moved to asm-sparc.
The remaining files (71 files) were too different to be trivially
merged so divide them up in a _32.h and a _64.h file which
are both included from the file with no bit size.

The following script were used:
cd include
FILES=`wc -l asm-sparc64/*h | grep -v '^     1' | cut -b 20-`

for FILE in ${FILES}; do
  echo $FILE:
  BASE=`echo $FILE | cut -d '.' -f 1`
  FN32=${BASE}_32.h
  FN64=${BASE}_64.h
  GUARD=___ASM_SPARC_`echo $BASE | tr '-' '_' | tr [:lower:] [:upper:]`_H
  git mv asm-sparc/$FILE asm-sparc/$FN32
  git mv asm-sparc64/$FILE asm-sparc/$FN64
  echo git mv done
  printf "#ifndef %s\n" $GUARD                             >   asm-sparc/$FILE
  printf "#define %s\n" $GUARD                             >>  asm-sparc/$FILE
  printf "#if defined(__sparc__) && defined(__arch64__)\n" >>  asm-sparc/$FILE
  printf "#include <asm-sparc/%s>\n" $FN64                 >>  asm-sparc/$FILE
  printf "#else\n"                                         >>  asm-sparc/$FILE
  printf "#include <asm-sparc/%s>\n" $FN32                 >>  asm-sparc/$FILE
  printf "#endif\n"                                        >>  asm-sparc/$FILE
  printf "#endif\n"                                        >>  asm-sparc/$FILE
  git add asm-sparc/$FILE
  echo new file done
  printf "#include <asm-sparc/%s>\n" $FILE                 >  asm-sparc64/$FILE
  git add asm-sparc64/$FILE
  echo sparc64 file done
done

The guard contains three '_' to avoid conflict with existing guards.
In additing the two Kbuild files are emptied to avoid breaking
headers_* targets.
We will reintroduce the exported header files when the necessary
kbuild changes are merged.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices have more than 15 which was the previous
setting.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sabre and Psycho PCI controllers can have partial interrupt-map
properties, meaning that on-board devices don't match up to any
entries.  Instead, they are fully specified from the beginning and
we should pass them directly to the IRQ translator as-is.

Also, fill in the necessary translator slots for the "graphics"
and "expansion UPA" interrupts on Sabre, Psycho, and SYSIO SBUS.

Increase PROMREG_MAX to 24, as seen on SUNW,ffb devices.

Finally, prevent accidentally writing past the end of the of_device
struct resource[] and irqs[] arrays.  Spit out a log message when
we ignore some entries because there are too many of them.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete all of the code working with sp_banks[] and replace
with clean acquisition and sorting of physical memory
parameters from the firmware.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!