Add DT property to tell the TPS6586x that it should provide the
pm_power_off() implementation. This allows "shutdown" to work.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Harmony uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.

Based on Ventana regulator patch by Stephen Warren <swarren@nvidia.com>
and converted to Harmony.

swarren made the following changes:
* Added ldo0 regulator configuration to device tree, and updated
  board-harmony-pcie.c for the new regulator name.
* Fixed vdd_1v05's voltage from 10.5V to 1.05V.
* Modified board-harmony-pcie.c to obtain the en_vdd_1v05 GPIO number at
  run-time from device tree instead of hard-coding it.
* Removed board-harmony{-power.c,.h} now that they're unused.
* Disabled vdd_1v05 regulator; the code in board-harmony-pcie.c hijacks
  this GPIO for now. This will be fixed when the PCIe driver is re-
  written as a driver. The code can't regulator_get("vdd_1v05") right
  now, because the vdd_1v05 regulator's probe gets deferred due to its
  supply being the PMIC, which gets probed after the regulator the first
  time around, and this dependency is only resolved by repeated probing,
  which happens when deferred_probe_initcall() is called, which happens
  in a late initcall, whose runtime order relative to harmony_pcie_init()
  is undefined, since that's also called from a late initcall.
* Removed unused harmony_pcie_initcall().
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Harmony can be booted using device tree with equal functionality as when
booted using a board file. Remove as much of the board file as is
possible, since it's no longer needed.

Two special-cases are still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet, and the Harmony .dts file
doesn't yet describe regulators which are needed for PCIe. This logic is
now enabled unconditionally rather than via CONFIG_MACH_HARMONY. While
this is more code than other boards, it's still unlikely to be much of a
problem, and both regulators and PCIe should be supported via device tree
in the near future, allowing the remaining code to be removed.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Paz00 (Toshiba AC100) can be booted using device tree with equal
functionality as when booted using a board file. Remove as much of the
board file as is possible, since it's no longer needed.

One special-case is still left in board-dt-tegra20.c, since there is no
way to create a WiFi rfkill device from device tree yet. This logic is
now enabled unconditionally rather than via CONFIG_MACH_PAZ00. The extra
cases where it's enabled (.configs which did not enable Paz00 support)
shouldn't impact much since the amount of code is tiny.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-By: NMarc Dietrich <marvin24@gmx.de>

TrimSlice can be booted using device tree with equal functionality as
when booted using a board file. Remove the board file since it's no
longer needed.

One special-case is still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet. This logic is now enabled
by CONFIG_TEGRA_PCI rather than via CONFIG_MACH_TRIMSLICE. The extra
cases where it's enabled (.configs which did not enable TrimSlice
support) shouldn't impact much since the amount of code is tiny.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Clockevent's frequency is changed upon cpufreq change
notification. It fetches local timer's rate to update the
clockevent frequency. This patch adds local timer clock
for Tegra20.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

When changing a PLL's rate, it must have no active children. The CPU
clock cannot be stopped, and CPU clock's divider is not used. The old
clock driver used to handle this by internally reparenting the CPU clock
onto a different PLL when changing the CPU clock rate. However, the new
common-clock based clock driver does not do this, and probably cannot do
this due to the locking issues it would cause.

To solve this, have the Tegra cpufreq driver explicitly perform the
reparenting operations itself. This is probably reasonable anyway,
since such reparenting is somewhat a matter of policy (e.g. which
alternate clock source to use, whether to leave the CPU clock a child
of the alternate clock source if it's running at the desired rate),
and hence is something more appropriate for the cpufreq driver than
the core clock driver anyway.

Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

32-bit math isn't enough when e.g. *prate=12000000, and sel->n=1000.
Use 64-bit math to prevent this.

Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Warnings were generated because following commit changed data type for
address pointer

195bbcac ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors

arch/arm/mach-tegra/tegra30_clocks.c: In function 'clk_measure_input_freq':
arch/arm/mach-tegra/tegra30_clocks.c:418:2: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
.../arch/arm/include/asm/io.h:88:20: note: expected 'volatile void *' but argument is of type 'unsigned int
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

tegra_time is a struct sys_timer, not a struct clk, so can't be included
in an array of struct clk *.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

It should use tegra30_audio_sync_clk_ops for tegra30. It will cause
the tegra30 use the wrong audio_sync_clk_ops when build a kernel with
a tegra20 and tegra30 both supported kernel. And building error when
a tegra30-only kernel.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Currently the tegra20 and tegra30 share the same symbol for
tegra_clk_32k_ops. This will cause a compile error when building
a tegra20-only kernel image. Add tegra_clk_32k_ops for tegra20 and
modify tegra30_clk_32k_ops for tegra30.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Remove Tegra legacy clock framework code.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch converts tegra clock code to generic clock framework in following way:
 - Implement clk_ops as required by generic clk framework. (tegraXX_clocks.c)
 - Use platform specific struct clk_tegra in clk_ops implementation instead of struct clk.
 - Initialize all clock data statically. (tegraXX_clocks_data.c)

Legacy framework did not have recalc_rate and is_enabled functions. Implemented these functions.
Removed init function. It's functionality is splitted into recalc_rate and is_enabled.

Static initialization is used since slab is not up in .init_early and clock
is needed to be initialized before clockevent/clocksource initialization.
Macros redefined for clk_tegra.

Also, single struct clk_tegra is used for all type of clocks (PLL, peripheral etc.). This
is to move quickly to generic common clock framework so that other dependent features will
not be blocked (such as DT binding).

Enabling COMMON_CLOCK config moved to ARCH_TEGRA since it is enabled for both Tegra20
and Tegra30.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add Tegra platform specific clock structure clk_tegra and
some helper functions for generic clock framework.

struct clk_tegra is the single strcture used for all types of
clocks. reset and cfg_ex ops moved to clk_tegra from clk_ops.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Make the name consistent with other files.
s/tegra2/tegra20
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Move clock initialization data to separate file. This is
required for migrating to generic clock framework if static
initialization is used.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Move clock initialization data to separate file. This is
required for migrating to generic clock framework if static
initialization is used.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

A U16 divider can divide a clock by 1..64K. However, the range-check
in clk_div16_get_divider() limited the range to 1..256. Fix this. NVIDIA's
downstream kernels already have the fixed range-check.

In practice this is a problem on Whistler's I2C bus, which uses a bus
clock rate of 100KHz (rather than the more common 400KHz on Tegra boards),
which requires a HW module clock of 8*100KHz. The parent clock is 216MHz,
leading to a desired divider of 270. Prior to conversion to the common
clock framework, this range error was somehow ignored/irrelevant and
caused no problems. However, the common clock framework evidently has
more rigorous error-checking, so this failure causes the I2C bus to fail
to operate correctly.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Some boards use UART D for the main serial console, and some use UART A.
UART D's clock is listed in board-dt-tegra20.c's clock table, whereas
UART A's clock is not. This causes the clock code to think UART A's
clock is unsed. The common clock framework turns off unused clocks at
boot time. This makes the kernel appear to hang. Add UART A's clock into
the clock table to prevent this. Eventually, this requirement should be
handled by the UART driver, and/or properties in a board-specific device
tree file.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Nothing from this file is needed, so remove the include. This helps
single zImage work by reducing use of the mach-tegra/include/mach/
directory.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NChris Ball <cjb@laptop.org>

Nothing from these files is needed, so remove the includes. This helps
single zImage work by reducing use of the mach-tegra/include/mach/
directory.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

ARCH_TEGRA (arch/arm/Kconfig) now selects USE_OF, so there's not need
for ARCH_TEGRA_3x_SOC to do so too.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Use macro IO_ADDRESS for getting virtual address of
corresponding physical address to make the consistency
with rest of Tegra code-base.
This macro calls the IO_TO_VIRT() which is defined in
arch/arm/mach-tegra/include/mach/iomap.h
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.

[swarren: Instantiate the sys regulator from board-harmony-power.c to
 avoid regression.]
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: NAndreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: NForest Bond <forest.bond@rapidrollout.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Pull btrfs fixes from Chris Mason:
 "I've split out the big send/receive update from my last pull request
  and now have just the fixes in my for-linus branch.  The send/recv
  branch will wander over to linux-next shortly though.

  The largest patches in this pull are Josef's patches to fix DIO
  locking problems and his patch to fix a crash during balance.  They
  are both well tested.

  The rest are smaller fixes that we've had queued.  The last rc came
  out while I was hacking new and exciting ways to recover from a
  misplaced rm -rf on my dev box, so these missed rc3."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: fix that repair code is spuriously executed for transid failures
  Btrfs: fix ordered extent leak when failing to start a transaction
  Btrfs: fix a dio write regression
  Btrfs: fix deadlock with freeze and sync V2
  Btrfs: revert checksum error statistic which can cause a BUG()
  Btrfs: remove superblock writing after fatal error
  Btrfs: allow delayed refs to be merged
  Btrfs: fix enospc problems when deleting a subvol
  Btrfs: fix wrong mtime and ctime when creating snapshots
  Btrfs: fix race in run_clustered_refs
  Btrfs: don't run __tree_mod_log_free_eb on leaves
  Btrfs: increase the size of the free space cache
  Btrfs: barrier before waitqueue_active
  Btrfs: fix deadlock in wait_for_more_refs
  btrfs: fix second lock in btrfs_delete_delayed_items()
  Btrfs: don't allocate a seperate csums array for direct reads
  Btrfs: do not strdup non existent strings
  Btrfs: do not use missing devices when showing devname
  Btrfs: fix that error value is changed by mistake
  Btrfs: lock extents as we map them in DIO
  ...