In the OF 'translations' property, the template TTEs in the mappings
never specify the executable bit.  This is the case even though some
of these mappings are for OF's code segment.

Therefore, we need to force the execute bit on in every mapping.

This problem can only really trigger on Niagara/sun4v machines and the
history behind this is a little complicated.

Previous to sun4v, the sun4u TTE entries lacked a hardware execute
permission bit.  So OF didn't have to ever worry about setting
anything to handle executable pages.  Any valid TTE loaded into the
I-TLB would be respected by the chip.

But sun4v Niagara chips have a real hardware enforced executable bit
in their TTEs.  So it has to be set or else the I-TLB throws an
instruction access exception with type code 6 (protection violation).

We've been extremely fortunate to not get bitten by this in the past.

The best I can tell is that the OF's mappings for it's executable code
were mapped using permanent locked mappings on sun4v in the past.
Therefore, the fact that we didn't have the exec bit set in the OF
translations we would use did not matter in practice.

Thanks to Greg Onufer for helping me track this down.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If "-p" is given on the command line, clear the CON_BOOT
flag for the initial early boot PROM console.

This is necessary to try and see crash messages that occur
between the registry of the VT console and the probing of
the first framebuffer or serial console.  During this time
no console messages are emitted because the VT console
registry (even if no backend is registered to it) removes
the early console if CON_BOOT is set.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The address limit is already set in flush_old_exec() so this assignment of
USER_DS is redundant.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recognize T4 and T5 chips.  Treating them both as "T2 plus other
stuff" should be extremely safe and make sure distributions will work
when those chips actually ship to customers.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
  netpoll: fix incorrect access to skb data in __netpoll_rx
  cassini: init before use in cas_interruptN.
  can: ti_hecc: Fix uninitialized spinlock in probe
  can: ti_hecc: Fix unintialized variable
  net: sh_eth: fix the compile error
  net/phy: fix DP83865 phy interrupt handler
  sendmmsg/sendmsg: fix unsafe user pointer access
  ibmveth: Fix leak when recycling skb and hypervisor returns error
  arp: fix rcu lockdep splat in arp_process()
  bridge: fix a possible use after free
  bridge: Pseudo-header required for the checksum of ICMPv6
  mcast: Fix source address selection for multicast listener report
  MAINTAINERS: Update GIT trees for network development
  ath9k: Fix PS wrappers in ath9k_set_coverage_class
  carl9170: Fix mismatch in carl9170_op_set_key mutex lock-unlock
  wl12xx: add max_sched_scan_ssids value to the hw description
  wl12xx: Fix validation of pm_runtime_get_sync return value
  wl12xx: Remove obsolete testmode NVS push command
  bcma: add uevent to the bus, to autoload drivers
  ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc32,sun4d: Change IPI IRQ level to prevent collision between IPI and timer interrupt
  sparc: Remove another reference to nfsservctl

Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
  ARM: mach-shmobile: sh7372 CMT3 and CMT4 clock support
  ARM: mach-shmobile: sh7372 MSIOF clock support
  ARM: mach-shmobile: clock-sh7372: fixup USB-DMAC1 settings
  ARM: mach-shmobile: clock-sh73a0: tidyup CKSCR main clock selecter
  ARM: mach-shmobile: Remove 3DG/SGX from sh7372 INTCS
  ARM: mach-shmobile: mackerel: Add USB-DMA ID
  mmc: sdhi, mmcif: zboot: Correct clock disable logic
  ARM: mach-shmobile: ag5evm: SDHI requires waiting for idle
  ARM: static should be at beginning of declaration
  ARM: mach-shmobile: Use CMT2 for timer on sh7372
  ARM: mach-shmobile: sh7372: Add USB-DMAC support

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
  sh: fix the compile error in setup-sh7757.c
  serial: sh-sci: report CTS as active for get_mctrl
  sh: Add unaligned memory access for PC relative intructions
  sh: Fix unaligned memory access for branches without delay slots
  sh: Fix up fallout from cpuidle changes.
  serial: sh-sci: console Runtime PM support
  sh: Fix conflicting definitions of ptrace_triggered
  serial: sh-sci: fix DMA build by including dma-mapping.h
  serial: sh-sci: Fix up default regtype probing.
  sh: intc: enable both edges GPIO interrupts on sh7372
  shwdt: fix usage of mod_timer
  clocksource: sh_cmt: wait for CMCNT on init V2

As Paul has not much time for it I take over maintaining the
framebuffer subsystem.
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On Sun4d systems running in SMP mode, IRQ 14 is used for timer interrupts
and has a specialized interrupt handler. IPI is currently set to use IRQ 14
as well, which causes it to trigger the timer interrupt handler, and not the
IPI interrupt handler.

The IPI interrupt is therefore changed to IRQ 13, which is the highest
normally handled interrupt. This IRQ is also used for SBUS interrupts,
however there is nothing in the IPI/SBUS interrupt handlers that indicate
that they will not handle sharing the interrupt.
(IRQ 13 is indicated as audio interrupt, which is unlikely to be found in a
sun4d system)
Signed-off-by: NKjetil Oftedal <oftedal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add clock control support for sh7372 CMT hardware blocks.

No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.

This patch relies on the recently merged

 794d78fe drivers: sh: late disabling of clocks V2

to make sure the unused clocks get disabled as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add clock control support for sh7372 MSIOF hardware blocks.

No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.

This patch relies on the recently merged

 794d78fe drivers: sh: late disabling of clocks V2

to make sure the unused clocks get disabled as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

MAINCKSEL is [29:28], not [27:24]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.

The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.

Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.

If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the following build errors:

  CC      arch/sh/kernel/cpu/sh4a/setup-sh7757.o
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: implicit declaration of function ‘DMA_BIT_MASK’
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: initializer element is not constant
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: (near initialization for ‘usb_ehci_device.dev.coherent_dma_mask’)
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:705: error: initializer element is not constant
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:705: error: (near initialization for ‘usb_ohci_device.dev.coherent_dma_mask’)
make[3]: *** [arch/sh/kernel/cpu/sh4a/setup-sh7757.o] Error 1
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sh-sci.c sets hardware up and then let the HW do all flow controls.
There is no software code, nor needs to get/set real CTS signal.

But, when turning CRTSCTS on through termios, uart_set_termios() in
serial_core.c checks CTS, and stops TX if it is inactive at the moment.

Because sci_get_mctrl() returns a fixed value DTR|RTS|DSR but CTS,
the sequence
  open -> set CRTSCTS -> write
hit the case and stop working, no more outputs.

This patch makes sci_get_mctrl() report CTS in addition.
Signed-off-by: NTakashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds unaligned memory access support for the following instructions:
  mov.w @(disp,PC),Rn
  mov.l @(disp,PC),Rn

These instructions are often used on SH2A toolchains.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch just clears the return code for those cases where an
unaligned memory access occurs on branch instructions without a
delay slot.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
  OMAP: omap_device: only override _noirq methods, not normal suspend/resume
  PM / Runtime: Correct documentation of pm_runtime_irq_safe()
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix
  sh-sci / PM: Use power.irq_safe
  PM: Use spinlock instead of mutex in clock management functions

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: fix panic after rmmod with slow targets

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
  i915: do not setup intel_backlight twice

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: ftdi_sio: add Calao reference board support
  USB option driver K3765/K4505 avoid CDC_DATA interface
  USB: option: add YUGA device id to driver
  usb: s5p-ehci: fix a NULL pointer deference
  USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
  USB option driver add PID of Huawei Vodafone K4605
  USB option driver add PID of Huawei Vodafone K3806
  xhci: Handle zero-length isochronous packets.
  USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
  usb: musb: gadget: fix error path
  usb: gadget: f_phonet: unlock in error case
  usb: musb: blackfin: include prefetch head file
  usb: musb: tusb6010: fix compilation
  usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
  usb: musb: cppi: fix build errors due to DBG and missing musb variable
  usb: musb: ux500: replace missing DBG with dev_dbg
  usb: musb: ux500: set dma config for both src and dst
  usb: musb: fix oops on musb_gadget_pullup
  usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
  usb: gadget: hid: don't STALL when processing a HID Descriptor request
  ...

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  omap-serial: Allow IXON and IXOFF to be disabled.
  TTY: serial, document ignoring of uart->ops->startup error
  TTY: pty, fix pty counting
  8250: Fix race condition in serial8250_backup_timeout().
  serial/8250_pci: delete duplicate data definition
  8250_pci: add support for Rosewill RC-305 4x serial port card
  tty: Add "spi:" prefix for spi modalias
  atmel_serial: fix atmel_default_console_device
  serial: 8250_pnp: add Intermec CV60 touchscreen device
  drivers/serial/ucc_uart.c: Fix compiler warning
  pch_uart: Set PCIe bus number using probe parameter
  serial: samsung: Fix build error

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  drivers:misc: ti-st: fix unexpected UART close
  drivers:misc: ti-st: free skb on firmware download
  drivers:misc: ti-st: wait for completion at fail
  drivers:misc: ti-st: reinit completion before send
  drivers:misc: ti-st: fail-safe on wrong pkt type
  drivers:misc: ti-st: reinit completion on ver read
  drivers:misc:ti-st: platform hooks for chip states
  drivers:misc: ti-st: avoid a misleading dbg msg
  base/devres.c: quiet sparse noise about context imbalance
  pti: add missing CONFIG_PCI dependency
  drivers/base/devtmpfs.c: correct annotation of `setup_done'
  driver core: fix kernel-doc warning in platform.c
  firmware: fix google/gsmi.c build warning

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  staging: tidspbridge: fix compilation on dsp clock functions
  staging: octeon-ethernet: Add missing #includes.
  Staging: zcache: signedness bug in tmem_get()
  staging: zcache: fix crash on high memory swap
  staging: brcm80211: SPARC build error fix
  staging: brcm80211: fix compile error on non-x86 archs since 3.0 kernel

__netpoll_rx() doesnt properly handle skbs with small header

pskb_may_pull() or pskb_trim_rcsum() can change skb->data, we must
reload it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Spotted-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ti_hecc_probe(), the spinlock  priv->mbx_lock is not
inited, causing a spinlock lockup BUG.
Acked-by: NAnant Gole <anantgole@ti.com>
Signed-off-by: NAbhilash K V <abhilash.kv@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ti_hecc_xmit(), local variable "data" is not initialized before
being used.
This initialization got inadvertently removed in the following patch:

	can: Unify droping of invalid tx skbs and netdev stats
Acked-by: NAnant Gole <anantgole@ti.com>
Signed-off-by: NAbhilash K V <abhilash.kv@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following build error:

  CC      drivers/net/sh_eth.o
drivers/net/sh_eth.c:1115: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘sh_eth_interrupt’
drivers/net/sh_eth.c: In function ‘sh_eth_open’:
drivers/net/sh_eth.c:1387: error: implicit declaration of function ‘request_irq’
drivers/net/sh_eth.c:1387: error: ‘sh_eth_interrupt’ undeclared (first use in this function)
drivers/net/sh_eth.c:1387: error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1387: error: for each function it appears in.)
drivers/net/sh_eth.c:1391: error: ‘IRQF_SHARED’ undeclared (first use in this function)
drivers/net/sh_eth.c:1424: error: implicit declaration of function ‘free_irq’
make[2]: *** [drivers/net/sh_eth.o] Error 1
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the DP83865 datasheet we need to clear
the interrupt status bit by writing a 1 to the
corresponding bit in INT_CLEAR (2:0 are reserved).

Proposed and tested by Thorsten.
Signed-off-by: NThorsten Schubert <tshu@msc-ge.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] memory hotplug: only unassign assigned increments
  [S390] Change default action from reipl to stop for on_restart
  [S390] arch/s390/kernel/ipl.c: correct error detection check
  [S390] drivers/s390/block/dasd_ioctl.c: add missing kfree
  [S390] nss,initrd: kernel image and initrd must be in different segments

According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.

Currently, we don't handle this special case and set irq field in
*_board_info structs to 255.  It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>