The check for retval being less than zero is always true since
retval equal to -EPIPE at that point.  Replace the existing
conditional with just return retval.

Detected with CoverityScan, CID#114349 ("Logically dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The "dbg_port" macro uses the "outside" parameter (="temp") instead of
the parameters (="value") given in the macro. As the macro can look
outside its definition this causes no direct problem.
Signed-off-by: NJelle Martijn Kok <jmkok@youcom.nl>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A pointer to musb is now present in the dma_controller structure.
Remove the one present in tusb_omap_dma structure.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi41_dma_controller structure.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi structure.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update cppi41_dma_callback() to detect an aborted transfer.
This was not required before because cppi41_dma_callback() was only
invoked on transfer completion.
In order to make CPPI 4.1 driver more generic, cppi41_dma_callback()
will be invoked after a transfer abort in order to let the MUSB driver
perform some action such as acknowledge the interrupt that may be fired
during a teardown.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, the CPPI 4.1 driver is not completely generic and
only works on DSPS. This is because of IRQ management.
Add a callback to dma_controller that could be invoked on DMA completion
to acknowledge the IRQ.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missing break statement to prevent the code for case
USB_PORT_FEAT_C_RESET falling through to the default case.

Addresses-Coverity-ID: 143155
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix another NULL-pointer dereference at open should a malicious device
lack an interrupt-in endpoint.

Note that the driver has a broken check for an interrupt-in endpoint
which means that an interrupt URB has never even been submitted.

Fixes: 3f542974 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org>	# v2.6.19: 5c75633eReviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop two redundant NULL checks from usb_serial_console_disconnect().

The usb_serial_console_disconnect function is called from the
USB-serial-device disconnect callback when a device is going away. Hence
there is no need to check for the serial-device pointer being NULL.

The serial-device port pointers are stored in an array that is a member
of the serial struct so the address of the first member of the array
(which the array name decays to) is never NULL either.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Since commit 4a510969 ("tty: Make tty_files_lock per-tty") a new
tty_struct spin lock is taken in the tty release path, but the
USB-serial-console hack was never updated hence leaving the lock of its
"fake" tty uninitialised. This was eventually detected by lockdep.

Make sure to initialise the new lock also for the fake tty to address
this regression.

Yes, this code is a mess, but cleaning it up is left for another day.

Fixes: 4a510969 ("tty: Make tty_files_lock per-tty")
Cc: stable <stable@vger.kernel.org>	# 4.6
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

No need to reinitialise the interrupt-in URB with values that have not
changed before (some) resubmissions.

This also allows the interrupt-in callback to have a single path for URB
resubmission.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop some unnecessary debug printks.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop redundant URB unlink as there's no need to unlink an URB which is
about to be killed synchronously.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop the unused interrupt-out callback.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Make the reference clock optional for DTS backward compatibility
and ignore the error if it does not exist.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the reference clock optional for DTS backward compatibility
and ignore the error if it does not exist.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The condition modex % 16 cannot be true when modex value is equal to 640
The condition du & 0xff cannot be true when du value is equal to 0x1400

Addresses-Coverity-Id: 101163
Addresses-Coverity-Id: 744373
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove this line of code because devnum is overwritten before it can be used.
This could happen if line of code 609 (goto try_again;) is executed. Otherwise,
devnum is never used again.

Addresses-Coverity-ID: 1226870
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface numbers do not change when enabling alternate settings as
comment and code in this driver suggested.

Remove the confusing comment and redundant retrieval of the interface
number in probe, while simplifying and renaming the interface-number
helper.

Fixes: 4db2299d ("sierra: driver interface blacklisting")
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).

When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.

In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.

This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: NMichael Walle <michael@walle.cc>
Fixes: 72fda3ca ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb69 ("USB: ftdi_sio: clean up line-status handling")
Cc: stable <stable@vger.kernel.org>	# v2.6.35
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design
change.
Signed-off-by: NKen Lin <yungching0725@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fixes the following sparse warning:

drivers/usb/musb/musb_dsps.c:270:6: warning:
 symbol 'dsps_musb_clear_ep_rxintr' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.

Add support for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.

Size details after cross compiling the .o file for arm
architecture.

File size before: drivers/usb/musb/omap2430.o
   text	   data	    bss	    dec	    hex	filename
   4141	    400	      8	   4549	   11c5	usb/musb/omap2430.o

File size after: drivers/usb/musb/omap2430.o
   text	   data	    bss	    dec	    hex	filename
   4333	    200	      8	   4541	   11bd	usb/musb/omap2430.o
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
[b-liu@ti.com: added omap2430 in commit subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We can now configure the PMIC interrupt to provide us VBUS
events. In that case we don't need to constantly poll the
status and can make it optional. This is only wired up
for the mini-B interface on beaglebone.

Note that eventually we should get also the connect status
for the host interface when the am335x internal PM coprocessor
provides us with an IRQ chip. For now, we still need to poll
for the host mode status.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_PM_SLEEP is disabled, SIMPLE_DEV_PM_OPS does not use
bfin_resume and bfin_suspend even if CONFIG_PM is enabled:

drivers/usb/musb/blackfin.c:602:12: warning: ‘bfin_resume’ defined but
not used [-Wunused-function]
 static int bfin_resume(struct device *dev)
            ^~~~~~~~~~~
drivers/usb/musb/blackfin.c:585:12: warning: ‘bfin_suspend’ defined but
not used [-Wunused-function]
 static int bfin_suspend(struct device *dev)
            ^~~~~~~~~~~~

The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However it is better to mark these functions as __maybe_unused.
Signed-off-by: NJérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The dsps glue uses PLATFORM_DEVID_AUTO when creating the musb-hdrc
platform devices, this causes that the id will change in each system
depending on the order of driver probe, the order of the usb instances
defined in device-tree, or the list of enabled devices which use also
PLATFORM_DEVID_AUTO in kernel config. This id inconsistency causes
trouble in shell scripting or user guide documentation.

So switch it to static id, starting from 0 to the musb instance with
lower MMR offset. This scheme is also aligned to the naming in the SoC.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on the musb ug, force_host bit is allowed to be set along with
force_hs or force_fs bit.

It could help to implement forced host mode via testmode on Nokia N900.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch just uses the resource-managed extcon API when registering
the extcon notifier.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.

Use the quirk MUSB_PRESERVE_SESSION to preseve MUSB_DEVCTL during suspend.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the  session during
a suspend.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement PM methods specifics for da8xx glue.
The only thing to do is to power off the phy.
As the registers are in retention during suspend,
there is no need to save them.
Signed-off-by: NAlexandre Bailon <abailon@baylibre.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

musb_generic_disable() only has two lines of code. So remove it and let
the callers directly call those two lines.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>