The following changes are invalid and should be
disallowed when a station already exists:
 * supported rates changes, except for TDLS peers
 * listen interval changes
 * HT capability changes

Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.

To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To simplify the locking and not require cfg80211_mutex
(which nl80211 uses to access the global regdomain) and
also to make it possible for drivers to access their
wiphy->regd safely, use RCU to protect these pointers.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a bug with the world regulatory domain, it
can be updated any time which is different from all
other regdomains that can only be updated once after
a request for them. Fix this by adding a check for
"processed" to the reg_is_valid_request() function
and clear that when doing a request.

While looking at this I also found another locking
bug, last_request is protected by the reg_mutex not
the cfg80211_mutex so the code in nl80211 is racy.
Remove that code as it only tries to prevent an
allocation in an error case, which isn't necessary.
Then the function can also become static and locking
in nl80211 can have a smaller scope.

Also change __set_regdom() to do the checks earlier
and not different for world/other regdomains.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This code is a bit too BUG_ON happy, remove all
instances and while doing so make some code a bit
smarter by passing the right pointer instead of
indices into arrays.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is pretty much useless since get_wiphy_idx()
always returns true since it's always called with
a valid wiphy pointer.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clean up various things like indentation, extra
parentheses, too many/few line breaks, etc.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.

Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There is a standalone if, seems to be a regression of commit
"nl80211/cfg80211: add VHT MCS support".
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Cleanup of unused VHT channel config related code.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The CQM TX-error rate/interval can't be less than
zero since they're unsigned values, remove checks.
Also fix indentation of the function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If a driver supports P2P GO powersave, allow it to
set the new feature flags for it and allow userspace
to configure the parameters for it. This can be done
at GO startup and later changed with SET_BSS.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some of the chandef checking that we do in cfg80211
to check if a channel is supported or not is also
needed in mac80211, so rework that a bit and export
the functions that are needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for reporting and calculating VHT MCSes.

Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The NL80211_CMD_TDLS_OPER command was previously used only for userspace
request for the kernel code to perform TDLS operations. However, there
are also cases where the driver may need to request operations from
userspace, e.g., when using security on the AP path. Add a new cfg80211
function for generating a TDLS operation event for drivers to request a
new link to be set up (NL80211_TDLS_SETUP) or an existing link to be
torn down (NL80211_TDLS_TEARDOWN). Drivers can optionally use these
events, e.g., based on noticing data traffic being sent to a peer
station that is seen with good signal strength.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The userspace may want to know what is the current ssid that a given
interface is using. This patch enables nl80211 to send the
NL80211_ATTR_SSID attribute in nl80211_send_iface().
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Store the configured ssid in wdev->ssid when starting an AP
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The commit:

commit 5e760230
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Nov 4 11:18:17 2011 +0100

    cfg80211: allow registering to beacons

allowed only a single process to register for beacon events
per wiphy.  This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.

This patch allows multiple beacon listeners, fixing the
regression.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This command triggers a new callback: set_mcast_rate(). It enables
the user to change the rate used to send multicast frames for vif
configured as IBSS or MESH_POINT
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Setting the wdev to NULL when the channel can't be
set for that interface type (to treat the channel
setting for the wiphy/monitor) currently works, but
is confusing in the code if netdev/wdev aren't both
set/unset in the same way. Move the check whether
the channel can be set to where it's needed so that
wdev and netdev are always both assigned or NULL.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These were missed due to the tracing work having
started on a kernel that didn't have P2P Device
yet, implement them now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow adding central tracing like in mac80211.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, a user is allowed to choose a HT operating channel
with WEP when creating an IBSS network. WEP is not allowed
in HT configuration - this patch ensures that such requests
are denied.
Signed-off-by: NSujith Manoharan <c_manoha@qti.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add an NL80211_SCAN_FLAG_FLUSH flag that causes old bss cache
entries to be flushed on scan completion. This is useful for
collecting guaranteed fresh scan/survey result (e.g. on resume).

For normal scan, flushing only happens on successful completion
of a scan; i.e. it does not happen if the scan is aborted.
For scheduled scan, previous scan results are flushed everytime
when we get new scan results.

This feature is enabled by default. Drivers can disable it by
unsetting the NL80211_FEATURE_SCAN_FLUSH flag.
Signed-off-by: NSam Leffler <sleffler@chromium.org>
Tested-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
[invert polarity of feature flag to account for old kernels]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add NL80211_SCAN_FLAG_LOW_PRIORITY flag support. It tells drivers
that this is a low priority scan request, so that they can take
necessary action.
Drivers need to advertise low priority scan capability during
registration.
Signed-off-by: NSam Leffler <sleffler@chromium.org>
Tested-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a flags word to direct and scheduled scan requests; it will
be used for control of optional behaviours such as flushing the
bss cache prior to doing a scan.
Signed-off-by: NSam Leffler <sleffler@chromium.org>
Tested-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To save STAs VHT caps in AP mode
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

SAE extends Authentication frames with fields that are not information
elements. NL80211_ATTR_IE is not suitable for these, so introduce a new
attribute that can be used to specify the fields needed for SAE in
station mode.
Signed-off-by: NJouni Malinen <j@w1.fi>
[change to verify that SAE is only used with authenticate command]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In AP mode, when a station requests connection to an AP and if the
request is failed for particular reason, userspace is notified about the
failure through NL80211_CMD_CONN_FAILED command. Reason for the failure
is sent through the attribute NL80211_ATTR_CONN_FAILED_REASON.
Signed-off-by: NPandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is a frequent mistake to confuse the netlink port identifier with a
process identifier.  Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.

I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.

I have successfully built an allyesconfig kernel with this change.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

connkeys is malloced in nl80211_parse_connkeys() and should
be freed in the error handling case, otherwise it will cause
memory leak.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.

This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.

Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.

As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Cellular base stations can provide hints to cfg80211 about
where they think we are. This can be done for example on
a cell phone. To enable these hints we simply allow them
through as user regulatory hints but we allow userspace
to clasify the hint as either coming directly from the
user or coming from a cellular base station. This option
is only available when you enable
CONFIG_CFG80211_CERTIFICATION_ONUS.

The base station hints themselves will not be processed
by the core unless at least one device on the system
supports this feature.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Let the user configure serveral TX error conection quality monitoring
parameters: % error rate, survey interval, and # of attempted packets.

On exceeding the TX failure rate over the given interval, the driver
will send a CQM notify event with the actual TX failure rate and
packets attempted.
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In one of my previous patches I erroneously
used nla_put_u32 for the wdev_id, fix that
to use nla_put_u64.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>