Preparation for updating common->macaddr along with virtual interface
MAC address changes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is called with spinlocks held so we have to use GFP_ATOMIC.  It's
the sc_pcu_lock in ath9k_stop() that's the issue.  The call tree looks
like this:

ath9k_stop()
ath_prepare_reset()
ath_stoprecv()
ath_flushrecv()
ath_rx_tasklet()
ath9k_dfs_process_phyerr()
pd->add_pulse() => dpd_add_pulse()
channel_detector_get()
channel_detector_create()
pri_detector_init()

channel_detector_create() uses GFP_ATOMIC as well.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Tested-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Acked-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The DFS pattern detector was initially planned to reside on
a higher layer and used generic pr_*() logging functions.

Being part of ath9k, use ath_dbg() instead and make DFS log
ouput selectable via ATH_DBG_DFS (0x20000) at runtime.

This patch does not contain functional modifications.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Inside one FIFO slot queue, EDMA chipsets have the same link pointer
re-read race condition as older chipsets, so the same buffer holding
logic needs to be used in order to avoid use-after-free bugs.
Unlike on older chips, it can be skipped for the end of the queue.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If AR_CRCErr, AR_PHYErr, AR_DecryptCRCErr or AR_MichaelErr is indicated
in the rx status word, but AR_RxFrameOK is also set, the descriptor
contents are typically invalid. This can show up as a warning about
invalid MCS rates in a frame. Even with those checks in place, a
descriptor with invalid MCS rates can still sometimes make it through to
the driver (mostly on older hardware like AR91xx).

Detect such errors in the last descriptor of a frame and discard the
whole frame if present.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As the comment in ath_get_next_rx_buf indicates, if a descriptor with
the done bit set follows one with the done bit cleared, both descriptors
should be discarded, however the driver is not doing that yet.

To fix this, use the rs->rs_more flag as an indicator that the following
frame should be discarded. This also helps with the split buffer case:
if the first part of the frame is discarded, the following parts need to
be discarded as well, since they contain no valid header or usable data.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of leaving the buffer without skb and breaking out of the loop
(which could leak the rx buffer), use the common error path.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is equivalent to ieee80211_hdrlen
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Banks 0-3,7 are neither modified at run time, nor SREV dependent.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are the remaining knobs in ath9k to support DFS:
* mark AR9280 and AR9580 as DFS tested
* synchronize DFS regulatory domain to reg notifyer
* set required RX filter flags for radar detection
* process radar PHY errors at DFS detector
* notify DFS master on radar detection

DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helps testing DFS without radar generating
equipment and is required for certification.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath_complete_reset will not be called if ath9k_hw_reset
is unsuccessful, so we need to re-enable intertupts to
balence the previous ath_prepare_reset call.  Also schedule a
reset as a best effort method to recover the chip from
whatever state caused the channel change failure.

Fixes https://bugzilla.kernel.org/show_bug.cgi?id=55771Signed-off-by: NRobert Shade <robert.shade@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The messages are currently hard coding "1ms", which does not match
the actual timeout being used.
Signed-off-by: NRobert Shade <robert.shade@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spectral data provided via relay-fs introduces a buffering
latency given by the subbuf_size. To meet the requirements for
delay-sensitive applications (like real-time spectral plotter),
reduce subbuf_size and increase n_subbufs.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following issue was reported.

WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]()
Hardware name: iMac12,1
queueing ieee80211 work while going to suspend
Pid: 0, comm: swapper/0 Tainted: PF          O 3.8.2-206.fc18.x86_64 #1
Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992]  <IRQ>
[<ffffffff8105e61f>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa0581420>] ? ath_start_rx_poll+0x70/0x70 [ath9k]
<ffffffff8105e716>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa045b542>] ieee80211_can_queue_work.isra.7+0x32/0x40

Fix this by avoiding to queue the work if our device has
already been marked as suspended or stopped.
Reported-by: NParag Warudkar <parag.lkml@gmail.com>
Tested-by: NParag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The beacon and multicast-buffer queues are managed by the beacon
tasklet, and the generic tx path hang check does not help in any way
here. Running it on those queues anyway can introduce some race
conditions leading to unnecessary chip resets.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.

That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).

Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the RX chainmask is set to 0x2 for AR9462, certain values
from chain1 have to be programmed for chain0 also.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This flag is used for indicating channel interference and
we currently do nothing with it, so remove it.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the embedded branch to make the ATH_EP_RND macro a little
clearer.  The new version also generates better code, saving 24
bytes of text:

   text	   data	    bss	    dec	    hex	filename
  87858	   1641	     24	  89523	  15db3	ath9k_orig.ko
  87834	   1641	     24	  89499	  15d9b	ath9k_new.ko

Although neither version handles negative values particularly well,
the lone caller clamps all negative values to zero anyway.  I have
verified that the results are the same for the range of possible
positive rssi values.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.

On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.

With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k commit 2ef16755
(ath9k: fix signal strength reporting issues) fixed an issue where the
reported per-frame signal strength reported to mac80211 was being
overwritten with an internal average. The same issue is also present
in ath9k_htc.
In addition to preventing the driver from overwriting the value, this
commit also ensures that the internal average (which is used for ANI)
only tracks beacons of the AP that we're connected to.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.

To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.

If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.

Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.

While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On joining an existing IBSS network, beaconing has to start
only after a TSF sync has happened by receiving a beacon from
the BSS. In creator mode, beaconing can start immediately after
a HW reset has been done.

Now that mac80211 notifies the driver of the mode type (creator/joiner)
via ieee80211_bss_conf->ibss_creator, make use of it to properly setup
the HW beacon timers.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a few places where the station's HT capabilities
should be checked instead of ATH9K_HW_CAP_HT, which is a global
feature for the driver. Fix this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

alloc failures already get standardized OOM
messages and a dump_stack.

For the affected mallocs around these OOM messages:

Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Remove now unused variables.
Remove unnecessary memset after kzalloc->kcalloc.
Whitespace cleanups for these changes.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Leaving the unused variables ath_mci_cleanup causes build warnings.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The relay file depends on relayfs. Trying to close this file without having
ATH9K_DEBUGFS (and therefore RELAY) activated causes build failures.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code is only used when ATH9K_DEBUGFS is activated and causes build warnings
when it is still compiled without user.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>