This patch adds a new hardware flag which indicate that the transceiver
doesn't support check for bad checksum via hardware. Also add a handling of
this while receive.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch splits the IEEE802154_HW_OMIT_CKSUM hardware flag into
IEEE802154_HW_TX_OMIT_CKSUM and IEEE802154_HW_RX_OMIT_CKSUM. This is
useful to deliver the received crc from the driver layer to the monitor
interface. At the moment we can't do that without change the xmit
handling.

The received checksum should be visible in monitor mode only.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a new driver operation to bring the transceiver into
promiscuous mode.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Overdue introduction for address filtering hardware flag. Furthermore we
will check and set address filtering on interface up. This patch
prepares that we can check if an transceiver supports address filtering
option. Currently all mainline driver supports hardware address filtering.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a new IEEE802154_HW_ARET hardware flag for indicating
that the transceiver supports ARET handling. Also remove the
IEEE802154_HW_FRAME_RETRIES from IEEE802154_HW_CSMA flag. Frame retries
handling is part of ARET.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes tabs after define in hardware flags declarations.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes the driver ops callbacks inside of wpan_phy struct.
It was used to check if a phy supports this driver ops call. We do this
now via hardware flags.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The range of channel and page fits into an unsigned byte range. This
patch changes the set_channel parameter definitions for channel and
page to u8.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ieee802154_ops structure should be never changed during runtime.
This patch declare this structure as const to avoid a runtime change.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a generic valid psdu length check function helper. This
is useful to check the length field after receiving. For example the
at86rf231 doesn't filter invalid psdu length. Sometimes the CRC can also
be correct. If we get the lqi value with an invalid frame length the
kernel may crash because we dereference an invalid pointer in the
receive buffer.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Tasklets have much less overhead than workqueues. This patch also
removes the heap allocation for the worker on receiving path.
Like mac80211 we should prefer use a tasklet here instead a workqueue to
getting fast out of interrupt context when ieee802154_rx_irqsafe is
called by driver. Like wireless inside the tasklet context we should
call netif_receive_skb instead netif_rx_ni anymore.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As we have decouple decompression from data delivery we can now rename all
occurences of process_data in receive path.
Signed-off-by: NMartin Townsend <mtownsend1973@gmail.com>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Acked-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Separating skb delivery from decompression ensures that we can support further
decompression schemes and removes the mixed return value of error codes with
NET_RX_FOO.
Signed-off-by: NMartin Townsend <mtownsend1973@gmail.com>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Acked-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a warning that xmit_sync callback is deprecated and
should be removed soon. The 802.15.4 subsystem will not accept synced
drivers anymore.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch renames the existsing xmit callback to xmit_sync and
introduces an asynchronous xmit_async function. If ieee802154_ops
doesn't provide the xmit_async callback, then we have a fallback to
the xmit_sync callback.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a new file net/mac802154/util.c which contains utility
functions for drivers, etc. This file contains functions to start and
stop queues for all virtual interfaces, this is useful for asynchronous
handling by driver level.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes the channel hopping feature before xmit. There are
several issues to provide a real channel hopping (timing requirements,
etc...).

We don't have any known kernelspace protocol which really use this
feature. And I don't know an real user of this feature.
We simply drop this feature now.

This patch removes also the hold of pib lock which isn't needed by any
real driver xmit callback implementation.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This driver_ops callback function is never used by any driver.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The identical struct of the wireless stack implementation is named
ieee80211_hw. This is useful to name the variable hw instead of get
confusing with netdev dev variable.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch moves the ieee802154 header into include/linux instead
include/net. Similar like wireless which have the ieee80211 header
inside of include/linux.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The wpan-phy header contains the wpan_phy struct information. Later this
header will be have similar function like cfg80211 header. The cfg80211
header contains the wiphy struct which is identically the wpan_phy
struct inside 802.15.4 subsystem.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a blank line after function declaration.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fix a checkpatch warning that __aligned(size) is preferred
over __attribute__((aligned(size))).
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixs a typo in address filter defines from IEEE802515 to
IEEE802154.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes the FSF address in files which belongs to ieee802154
and mac802154.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Systematically removing the LE connection parameters and autoconnect
action is inconvenient for rebonding without disconnecting from
userland (i.e. unpairing followed by repairing without
disconnecting). The parameters will be lost after unparing and
userland needs to take care of book-keeping them and re-adding them.

This patch allows userland to forget about parameter management when
rebonding without disconnecting. It defers clearing the connection
parameters when unparing without disconnecting, giving a chance of
keeping the parameters if a repairing happens before the connection is
closed.
Signed-off-by: NAlfonso Acosta <fons@spotify.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

There are scenarios when autoconnecting to a device after the
reception of an ADV_IND report (action 0x02), in which userland
might want to examine the report's contents.

For instance, the Service Data might have changed and it would be
useful to know ahead of time before starting any GATT procedures.
Also, the ADV_IND may contain Manufacturer Specific data which would
be lost if not propagated to userland. In fact, this patch results
from the need to rebond with a device lacking persistent storage which
notifies about losing its LTK in ADV_IND reports.

This patch appends the ADV_IND report which triggered the
autoconnection to the EIR Data in the Device Connected event.
Signed-off-by: NAlfonso Acosta <fons@spotify.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The values of a lot of the mgmt_device_connected() parameters come
straight from a hci_conn object. We can simplify the function by passing
the full hci_conn pointer to it.
Signed-off-by: NAlfonso Acosta <fons@spotify.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

$ make M=net/ipv4
  CC      net/ipv4/route.o
In file included from net/ipv4/route.c:102:0:
include/net/tcp.h: In function ‘tcp_v6_iif’:
include/net/tcp.h:738:32: error: ‘union <anonymous>’ has no member named ‘h6’
  return TCP_SKB_CB(skb)->header.h6.iif;
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: 870c3151 ("ipv6: introduce tcp_v6_iif()")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/dsa/slave.c uses functions and structures declared in phy_fixed.h
but does not explicitely include it, while dsa.h needs structure
declarations for 'struct ethtool_wolinfo' and 'struct ethtool_eee', fix
those by including the correct header files.

Fixes: ec9436ba ("net: dsa: allow drivers to do link adjustment")
Fixes: ce31b31c ("net: dsa: allow updating fixed PHY link information")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 971f10ec ("tcp: better TCP_SKB_CB layout to reduce cache line
misses") added a regression for SO_BINDTODEVICE on IPv6.

This is because we still use inet6_iif() which expects that IP6 control
block is still at the beginning of skb->cb[]

This patch adds tcp_v6_iif() helper and uses it where necessary.

Because __inet6_lookup_skb() is used by TCP and DCCP, we add an iif
parameter to it.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: 971f10ec ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Acked-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can retrieve opt from skb, no need to pass it as a parameter.
And opt should always be non-NULL, no need to check.

Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Tested-by: NKrzysztof Kolasa <kkolasa@winsoft.pl>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cookie_v4_check() allocates ip_options_rcu in the same way
with tcp_v4_save_options(), we can just make it a helper function.

Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid confusion between pid and portid.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EIRSR and ELRSR registers are 32-bit registers on GICv2, and we
store these as an array of two such registers on the vgic vcpu struct.
However, we access them as a single 64-bit value or as a bitmap pointer
in the generic vgic code, which breaks BE support.

Instead, store them as u64 values on the vgic structure and do the
word-swapping in the assembly code, which already handles the byte order
for BE systems.
Tested-by: NVictor Kamensky <victor.kamensky@linaro.org>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as users have been converted, so no need of this custom method
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The freescale driver uses custom device control FSLDMA_EXTERNAL_START to
put the controller in external start mode.
Since we are planning to deprecate the device control, move this to exported
API. Subsequent patches will remove the FSLDMA_EXTERNAL_START
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This was only prep API which didnt have an helper
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The driver library functions can be used directly by the compound devices such
as ADSP or serial driver where DesignWare DMA IP is privately attached to the
main hardware.

Instead of creating a new platform device leaf they may call dw_dma_probe()
with given struct dw_dma_chip directly and make sure that the main device is
DMA capable.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>