dev_set_drvdata() can't be used to set the driver private data pointer.
This would overwrite the led classdev object previously registered by
led_classdev_register().

Note that despite this mistake, the driver work fine because led_dat and
led_dat->cdev are at the same memory address.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch replace all the lock functions with the irq safe variant.
The ns2_led_{set,get}_mode() functions must be safe in all context.

For example, the trigger timer call led_set_brightness() in a softirq
context.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

When using simultaneously the two DMA channels on a same engine, some
transfers are never completed. For example, an endless lock can occur
while writing heavily on a RAID5 array (with async-tx offload support
enabled).

Note that this issue can also be reproduced by using the DMA test
client.

On a same engine, the interrupt cause register is shared between two
DMA channels. This patch make sure that the cause bit is only cleared
for the requested channel.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Tested-by: NLuc Saillard <luc@saillard.org>
Acked-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

We don't know how to enable it safely, especially as outputs turn on and
off.  When disabling LP1 we also need to make sure LP2 and 3 are already
disabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29173
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29082Reported-by: NChris Lord <chris@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.

As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep track of the link on the which the current request is in progress.
It allows support of links behind port multiplier.

Not all libata-sff is PMP compliant. Code for native BMDMA controller
does not take in accound PMP.

Tested on Marvell 7042 and Sil7526.
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For some mysterious reason, certain hardware reacts badly to usual EH
actions while the system is going for suspend.  As the devices won't
be needed until the system is resumed, ask EH to skip usual autopsy
and recovery and proceed directly to suspend.
Signed-off-by: NTejun Heo <tj@kernel.org>
Tested-by: NStephan Diestelhorst <stephan.diestelhorst@amd.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Patsburg (PCH) SATA AHCI and RAID Controller
DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Patsburg (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 978c0666 (libata: Remove excess delay in the tf_load path)
removed ata_wait_idle() from ata_sff_tf_load() and via_tf_load().
This caused obscure detection problems in sata_sil.

  https://bugzilla.kernel.org/show_bug.cgi?id=16606

The commit was pure performance optimization.  Revert it for now.
Reported-by: NDieter Plaetinck <dieter@plaetinck.be>
Reported-by: NJan Beulich <JBeulich@novell.com>
Bisected-by: Ngianluca <gianluca@sottospazio.it>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

It was a mistake to mark the PL031 IRQ as shared (for the U8500),
we misread the datasheet. Get rid of this.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace the arbitrary software-reset call from the device-probe
method, because:

- It is defective.  To work correctly, it should be two byte writes,
  not a single word write.  As it stands, it does nothing.

- Some devices with sx150x expanders installed have their NRESET pins
  ganged on the same line, so resetting one causes the others to reset -
  not a nice thing to do arbitrarily!

- The probe, usually taking place at boot, implies a recent hard-reset,
  so a software reset at this point is just a waste of energy anyway.

Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: NGregory Bean <gbean@codeaurora.org>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit b485fe5e ("rtc/m41t80: use rtc_valid_tm() to check returned tm")
added rtc_valid_tm to m41t80_rtc_read_alarm() but it was wrong while the
t->time does not contain complete date/time.

This patch also fixes a warning:
warning: passing argument 1 of 'rtc_valid_tm' from incompatible pointer type
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the second if (reg & ...) test into the branch indicated by its
indentation.  The test was previously always executed after the if
containing that branch, but it was always false unless the if branch was
taken.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.

mmc_suspend_host will enable host itself.  No need to enable host before
it.  Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe.  So make the mmc_host_enable after it.

[cjb: rebase against current Linus]
Signed-off-by: NEthan <ethan.too@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following error:

at91_mci.c: In function 'at91_mci_sg_to_dma':
at91_mci.c:236: error: implicit declaration of function 'kmap_atomic'
at91_mci.c:236: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:236: error: (Each undeclared identifier is reported only once
at91_mci.c:236: error: for each function it appears in.)
at91_mci.c:236: warning: assignment makes pointer from integer without a cast
at91_mci.c:252: error: implicit declaration of function 'kunmap_atomic'
at91_mci.c: In function 'at91_mci_post_dma_read':
at91_mci.c:302: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:302: warning: assignment makes pointer from integer without a cast
at91_mci.c:317: error: implicit declaration of function 'flush_kernel_dcache_page'
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes the following warning:

drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_suspend':
drivers/mmc/host/omap_hsmmc.c:2275: warning: unused variable 'state'

Introduced by commit ID:

  commit 1a13f8fa
  Author: Matt Fleming <matt@console-pimps.org>
  Date:   Wed May 26 14:42:08 2010 -0700

      mmc: remove the "state" argument to mmc_suspend_host()

The unique usage of this var was removed there, and missed
removing the respective declaration aswell.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[cjb: fix line-wrapped patch]
Signed-off-by: NJiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kunmap_atomic() takes the cookie, returned by the kmap_atomic() as its
argument and not the page address, used as an argument to kmap_atomic().
This patch fixes the compile error:

In file included from drivers/mmc/host/tmio_mmc.c:37:
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:192: error: negative width in bit-field '<anonymous>'
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Tested-by: NMagnus Damm <damm@opensource.se>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previously, it was possible for ack_mmc_irqs() to clear pending interrupt
bits in the CTL_STATUS register, even though the interrupt handler had not
been called.  This was because of a race that existed when doing a
read-modify-write sequence on CTL_STATUS.  After the read step in this
sequence, if an interrupt occurred (causing one of the bits in CTL_STATUS
to be set) the write step would inadvertently clear it.

Observed with the TMIO_STAT_RXRDY bit together with CMD53 on AR6002 and
BCM4318 SDIO cards in polled mode.

This patch eliminates this race by only writing to CTL_STATUS and clearing
the interrupts that were passed as an argument to ack_mmc_irqs()."

[matt@console-pimps.org: rewrote changelog]
Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>"
Tested-by: Arnd Hannemann <arnd@arndnet.de>"
Acked-by: NIan Molton <ian@mnementh.co.uk>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Added missing axis-mapping for HP ProBook 532x and HP Mini 5102.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Much (but not all) of the RTC state is kept in the RTC peripheral which
has its own power domain.  Periodically (1 HZ), that state is synced from
one power domain to the other (peripheral->core).  When we are resuming,
we need to wait for the sync to occur so that we don't get a mismatch of
reading undefined state in the rest of the driver.

Further, once the externally maintained bits have been synced back into
the core, we then need to restore the bits maintained in the core.  In our
particular case, that is just the write completion interrupt bit.

If we don't do any of this, working with the RTC causes ~5 second delays
from time to time after waking up due to the write completion interrupt
never firing.
Reported-by: NMichael Dean <mdean@aeronix.com>
Reported-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The int_clear helper takes a bitmask of interrupts to keep, not to
disable.  When suspending without wakeup enabled, we want to disable
all interrupts, so use 0 (keep none) instead of -1 (keep all).
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The introduction of support for SD combo cards breaks the initialization
of all CSR SDIO chips.  The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR
chips to be reset (this is non-standard behavior).

When initializing an SDIO card check for a combo card by using the memory
present bit in the R4 response to IO_SEND_OP_COND (CMD5).  This avoids the
call to mmc_sd_get_cid() on an SDIO-only card.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Acked-by: NMichal Mirolaw <mirq-linux@rere.qmqm.pl>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ahci_do_softreset() compared the current time and deadline in reverse
when calculating timeout for SRST issue.  The result is that if
@deadline is in future, SRST is issued with 0 timeout, which hasn't
caused any problem because it later waits for DRDY with the correct
timeout.  If deadline is already exceeded by the time SRST is about to
be issued, the timeout calculation underflows and if the device
doesn't respond, timeout doesn't trigger for a _very_ long time.

Reverse the incorrect comparison order.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: NGwendal Grignou <gwendal@google.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

x % 1 always evaluates to 0, which clearly isn't the intent. The
author probably had "% 2" or "& 1" in mind, and mispelled it.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

we're using a pointer through a freed command to reset the request,
which has shown up as an oops with slab poisoning:
Reported-by: NTejun Heo <tj@kernel.org>
Reported-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.

Fixes regression with e78d73b1.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073Reported-and-tested-by: NSitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During suspend, the power.completion is expected to be set when a
device has not yet started suspending.  Set it on init to fix a
corner case where a device is resumed when its parent has never
suspended.

Consider three drivers, A, B, and C.  The parent of A is C, and C
has async_suspend set.  On boot, C->power.completion is initialized
to 0.

During the first suspend:
suspend_devices_and_enter(...)
 dpm_resume(...)
  device_suspend(A)
  device_suspend(B) returns error, aborts suspend
 dpm_resume_end(...)
   dpm_resume(...)
    device_resume(A)
     dpm_wait(A->parent == C)
      wait_for_completion(C->power.completion)

The wait_for_completion will never complete, because
complete_all(C->power.completion) will only be called from
device_suspend(C) or device_resume(C), neither of which is called
if suspend is aborted before C.

After a successful suspend->resume cycle, where B doesn't abort
suspend, C->power.completion is left in the completed state by the
call to device_resume(C), and the same call path will work if B
aborts suspend.
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Changing state to CLOSING when FIN is received causes A0 cards to
hang.  Fix this by checking for A0 cards in FIN handling.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing.  By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core.  The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST.  The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event.  The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().

Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Setting TX pause param writes to the wrong register location causing
the adapter to hang.  Correct the define used to write the reigster.

Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=2116Reported-by: NShiri Franchi <shirif@voltaire.com>
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not.  However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command.  Therefore this is at least a local
denial-of-service vulnerability.

Change it to check before writing each entry and to return an error if
the buffer is already full.

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit b9421ae8.

This warning was so prelevant, even for apparently working machines,
that it was just causing fear, anxiety and panic.

The root cause still remains, so we will add some better debugging when
we focus on fixing it.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=17021Reported-by: NMaciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This reverts commit 0f3ee801.

Enabling LVDS on pipe A was causing excessive wakeups on otherwise idle
systems due to i915 interrupts. So restrict the LVDS to pipe B once more,
whilst the issue is properly diagnosed.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307Reported-and-tested-by: NEnrico Bandiello <enban@postal.uv.es>
Poked-by: NFlorian Mickler <florian@mickler.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org

It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.

So turn off SG, and we'll tackle making this work
properly in net-next-2.6
Reported-by: NDave Jones <davej@redhat.com>
Tested-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a simplified version of the original patch from James Courtier-Dutton.

>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>