This patch fixes the problem where each MTU change turns TSO,
GSO and GRO on from off state.

Now when TSO, GSO or GRO is turned off, MTU change does not
turn them on.
Signed-off-by: NPaweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous method for reading LLDP config was based on hard-coded
offsets. It happened to work, because of structured architecture of
the NVM memory. In the new approach, known as FLAT, we need to
calculate the absolute address, instead of using relative values.
Needed defines for memory location were added.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i40evf_add_vlan() is never called in atomic context.

i40evf_add_vlan() is only called by i40evf_vlan_rx_add_vid(),
which is only set as ".ndo_vlan_rx_add_vid" in struct net_device_ops.
".ndo_vlan_rx_add_vid" is not called in atomic context.

Despite never getting called from atomic context,
i40evf_add_vlan() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These flags were defined, but there is no use within the driver code, so
we don't need to keep them.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While doing some code review I noticed that we can get into a state where
we exit with the "IN_CRITICAL_TASK" bit set while notifying the PF of
flower filters. This patch is meant to address that plus tweak the ordering
of the while loop waiting on it slightly so that we don't wait an extra
period after we have failed for the last time.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It seems this is a copy-paste error and that the proper variable to use
in this particular case is _src_ instead of _dst_.

Addresses-Coverity-ID: 1465282 ("Copy-paste error")
Fixes: 0075fa0f ("i40evf: Add support to apply cloud filters")
Signed-off-by: NGustavo A R Silva <garsilva@embeddedor.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The checks to see if key->dst.s6_addr and key->src.s6_addr are null
pointers are redundant because these are constant size arrays and
so the checks always return true.  Fix this by removing the redundant
checks.   Also replace filter->f with vf, allowing wide lines to be
condensed and to rejoin some split wide lines.

Detected by CoverityScan, CID#1465279 ("Array compared to 0")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Passing struct virtchnl_filter f by value requires a 272 byte copy
on x86_64, so instead pass it by reference is much more efficient. Also
adjust some lines that are over 80 chars.

Detected by CoverityScan, CID#1465285 ("Big parameter passed by value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e_detect_recover_hung function uses the i40e_get_tx_pending
function to determine if there are packets stalled on the ring.
i40e_get_tx_pending calculates the pending packets using the head
writeback value and HW tail.  If the queue is stopped and we lose the
interrupt to update our next_to_clean then we a) won't get another
interrupt to clean because queue is stopped b) we won't catch the
problem with i40e_detect_recover_hung because the HW values look like
there's no packets waiting to be transmitted.  Using the SW values we
can catch the issue because next_to_clean will be out of sync with head
writeback.

This has the added benefit being less CPU intensive because we don't
need to reach into the hardware to get the values.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removes the locking of adapter->mac_vlan_list_lock resource in
i40evf_add_filter(). The locking part is moved above i40evf_add_filter().
i40evf_add_filter(), called by i40evf_addr_sync(), was trying to lock the
resource again and double locking generated a kernel panic after bringing
an interface up.

Fixes: 8946b563 ("i40evf: use __dev_[um]c_sync routines in
       .set_rx_mode")
Signed-off-by: NPaweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables a tc filter to be applied as a cloud
filter for the VF. This patch adds functions which parse the
tc filter, extract the necessary fields needed to configure the
filter and package them in a virtchnl message to be sent to the
PF to apply them.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support to configure bandwidth for the traffic
classes via tc tool. The required information is passed to the PF
which is used in the process of setting up the traffic classes.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allocates number of queues requested by the user as a part
of TC command when ADq is enabled on a VF.

In order to be consistent in design with PF implementation of ADq,
don't allow to set channels via ethtool from VF when ADq is already
enabled. This means the users will not be able to change the number of
queues/channels via ethtool for a VF when ADq is ON. In order to be
able to use set channels, users will be required to disable ADq first
and then try setting the channels again.

When ADq is enabled on VF, it goes through a reset during which VSIs
and queues are re-configured. Meanwhile if we receive link status
message from PF even before the queues are re-configured, just ignore
this link up message.
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces the callback to the ndo_setup_tc function
in the VF driver. We add a wrapper function to make room for the
upcoming cloud filter patches which add calls to different functions
from setup_tc.

First, we add support for capability exchange for ADQ between the
PF and VF. Next, we add support to take in the mqprio configuration
and configure queues as per the traffic classes, rate limit and the
priorities specified by the user. This is done by passing the channel
config to the PF driver through a virtchannel message.

The flags and bits added, track if ADq is enabled, set max number of
traffic classes to 4 and provide ability to negotiate capability with
the PF.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One of the previous patch fixes the link up issue by ignoring it if
i40evf is not in __I40EVF_RUNNING state. However this doesn't fix the
race condition when queues are disabled esp for ADq on VF. Hence check
if all queues are enabled before starting all queues.
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the PF resets the VF, the VF puts out a warning message
indicating that the VF received a reset message from the PF.
Make this message more clear so that we do not mistakenly
think that the PF is undergoing a reset.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to changes done to the PF driver in commit 6622f5cd ("i40e:
make use of __dev_uc_sync and __dev_mc_sync"), replace our
home-rolled method for updating the internal status of MAC filters with
__dev_uc_sync and __dev_mc_sync.

These new functions use internal state within the netdev struct in order
to efficiently break the question of "which filters in this list need to
be added or removed" into singular "add this filter" and "delete this
filter" requests.

This vastly improves our handling of .set_rx_mode especially with large
number of MAC filters being added to the device, and even results in
a simpler .set_rx_mode handler.

Under some circumstances, such as when attached to a bridge, we may
receive a request to delete our own permanent address. Prevent deletion
of this address during i40evf_addr_unsync so that we don't accidentally
stop receiving traffic.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When iterating through the linked list of VLAN filters, make the
iterator the same type as that of the linked list.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A spin lock is taken here so we should use GFP_ATOMIC.

Fixes: 504398f0 ("i40evf: use spinlock to protect (mac|vlan)_filter_list")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.

The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.

The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.

One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.

The first value current_itr represents the current value of the register.

The second value target_itr represents the desired value of the register.

The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While testing code for the recent ITR changes I found that updating the Tx
ITR appeared to have no effect with everything defaulting to the Rx ITR. A
bit of digging narrowed it down the fact that we were asking the PF to
associate all causes with ITR 0 as we weren't populating the itr_idx values
for either Rx or Tx.

To correct it I have added the configuration for these values to this
patch. In addition I did some minor clean-up to just add a local pointer
for the vector map instead of dereferencing it based off of the index
repeatedly. In my opinion this makes the resultant code a bit more readable
and saves us a few characters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.

This helps to make the code more readable as we can quickly translate from
one value to the other.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The CLEARPBA bit in the dynamic interrupt control register actually has
no effect either way on the hardware. As per errata 28 in the XL710
specification update the interrupt is actually cleared any time the
register is written with the INTENA_MSK bit set to 0. As such the act of
toggling the enable bit actually will trigger the interrupt being
cleared and could lead to potential lost events if auto-masking is
not enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a further clean-up related to the change over to using
q_vector->reg_idx when accessing the ITR registers. Specifically the code
appears to have several other spots where we were computing the register
offset manually and this resulted in errors in a few spots.

Specifically in the i40evf functions for mapping queues to vectors it
appears we may have had an off by 1 error since (v_idx - 1) for the first
q_vector with an index of 0 would result in us returning -1 if I am not
mistaken.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The logic for dynamic ITR update is confusing at best as there were odd
paths chosen for how to find the rings associated with a given queue based
on the vector index and other inconsistencies throughout the code.

This patch is an attempt to clean up the logic so that we can more easily
understand what is going on. Specifically if there is a Rx or Tx ring that
is enabled in dynamic mode on the q_vector it is allowed to override the
other side of the interrupt moderation. While it isn't correct all this
patch is doing is cleaning up the logic for now so that when we come
through and fix it we can more easily identify that this is wrong.

The other big change made here is that we replace references to:
	vsi->rx_rings[q_vector->v_idx]->itr_setting
with:
	q_vector->rx.ring->itr_setting

The general idea is we can avoid the long pointer chase since just
accessing q_vector->rx.ring is a single pointer access versus having to
chase down vsi->rx_rings, and then finding the pointer in the array, and
finally chasing down the itr_setting from there.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

'bufer' should be 'buffer'
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When compared to ixgbe and other previous Intel drivers the i40e and i40evf
drivers actually reserve 2 additional descriptors in maybe_stop_tx for
cache line alignment. We need to update DESC_NEEDED to reflect this as
otherwise we are more likely to return TX_BUSY which will cause issues with
things like xmit_more.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.

I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up unnecessary parenthesis.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

This patch enables driver to display LLDP information on the vSphere Web
Client with Intel adapters (X710, XL710) and Distributed Virtual Switch.
Signed-off-by: NUpasana Menon <upasana.menon@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds back the capability to turn off offloads when VF has
VLAN set. The commit 0a3b4f70 ("i40evf: enable support for VF VLAN
tag stripping control") adds the i40evf_set_features function and
changes the 'turn off' flow for offloads. This patch adds that
capability back by moving checking the VLAN option for VF to the
next statement.
Signed-off-by: NPaweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FW has the ability to return a critical error on every AQ command.
When this critical error occurs then we need to send the correct response
to the caller.
Signed-off-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang.  This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.

The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts.  By triggering a SW
interrupt, interrupts are forced on.  If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.

This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>