This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.

Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.

Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).

Compile-tested, based on latest mainline git.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reviewed-by: NJohn Pilles <jpilles@bb-elec.com>
Signed-off-by: NCliff Brake <cbrake@bec-systems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: NRainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I'd like to present my small patch enabling to use Hameg HM8143 programmable
power supply with linux.
Signed-off-by: NPawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

reference:
http://www.open-rd.orgSigned-off-by: NDhaval Vasa <dhaval.vasa@einfochips.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/Signed-off-by: NMarko Hänninen <bugitus@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: NVille Sundberg <vsundber@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds USB ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter.
Signed-off-by: NKrzysztof Ha³asa <khc@pm.waw.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It enhances the driver for FTDI-based USB serial adapters to recognize and
support Northern Digital Inc (NDI) measurement equipment. NDI has been
providing this patch for various kernel flavors for several years and we would
like to see these changes built in to the driver so that our equipement works
without the need for customers to patch the kernel themselves.

The patch makes small modifications to 2 files: ./drivers/usb/serial/ftdi_sio.c
and ./drivers/usb/serial/ftdi_sio.h. It accomplishes 3 things:

1. Define the VID and PIDs to allow the driver to recognize the NDI devices.
2. Map the 19200 baud rate setting to our higher baud rate of 1.2Mb
   We would have chosen to map 38400 to the higher rate, similar to what
   several other vendors have done, but some of our legacy customers actually
   use 38400, therefore we remap 19200 to the higher rate.
3. We set the default transmit latency in the FTDI chip to 1ms for our devices.
   Our devices are typically polled at 60Hz and the default ftdi latency
   seriously affects turn-around time and results in missed data frames. We
   have created a modprobe option that allows this setting to be increased.
   This has proven necessary particularly in some virtualized environments.
Signed-off-by: NMartin P. Geleynse <mgeleyns@ndigital.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It seems an USB device with vendor id 0403 and product code FB80 has an
FTDI serial io chip as well: http://ftdichip.com/Drivers/D2XX.htm
This device in fact is a true random generantor by comsci:
http://comscire.com/Products/R2000KU/
So the following patch should add support for this device if I am
correct. Not tested as I do not own this device (I would like support in
the kernel so that my entropybroker application (which distributes
entrop data (random values) between servers and clients)).


From: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The product ID's for the following devices have been added:
- LOAD-n-GO
- ICD-U64
- PRIME-8
Signed-off-by: NJan Capek <jan@ccsinfo.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added support for FTDI's USB 2.0 hi-speed devices - FT2232H (2
interfaces) and FT4232H (4 interfaces), including a new baud rate
calculation for these devices which can now achieve up to 12Mbaud by
turning off a divide by 2.5 in the baud rate generator of the chips.  In
order to achieve baud rates of <1200 baud, the divide by 2.5 must be
active.  The default product ID of the FT2232H is 0x6010 (same as the
FT2232C IC).  The default PID of the FT4232H is 0x6011.
Signed-off-by: NMark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I would like to have added new device to usbserial/ftdi_sio driver.
These ids used USB track device (http://www.l-and-b.dk/access_alt.html).
They use differend device IDs, but it works as standard usb-serial
conventer.

From: Daniel Suchy <danny@danysek.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For reference:
http://www.marvell.com/products/embedded_processors/developer/kirkwood/sheevaplug.jspSigned-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the following devices to the USB FTDI SIO device table:

 Bus 001 Device 009: ID 03eb:2109 Atmel Corp.
 http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4187

 Bus 001 Device 008: ID 1cf1:0001
 http://www.dresden-elektronik.de/shop/prod75.html

 Bus 001 Device 007: ID 1c1f:0004
 http://www.dresden-elektronik.de/shop/prod64.htmlSigned-off-by: NAxel Wachtler <axel.wachtler@atmel.com>
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for the NDI Polaris system *http://www.ndigital.com/).

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: NMhayk Whandson <eu@mhayk.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: NRobie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following patch adds in the USB PID for Ewert Energy System's CANdapter
device (CANBUS to USB-Serial which uses the FTDI 245R chipset) to the ftdi_sio
device driver.

The patch was tested successfully on Linux kernel 2.6.27 under Ubuntu.

Relevant output from /proc/bus/usb/devices (With patch installed):

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=9f80 Rev= 6.00
S:  Manufacturer=Ewert Energy Systems
S:  Product=CANdapter
S:  SerialNumber=A6RGB3Z3
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 90mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ftdi_sio
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
Signed-off-by: NAndrew Ewert <andrew@ewertenergy.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Someone on rmweb reminded me this had been overlooked from ages ago..

Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add Oceanic PID to ftdi_sio driver

Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a  PID of 0xf460.  The
attached patch adds that pid to ftdi_sio; driver  connects to my VT3
after that.
Signed-off-by: NVladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support for Domintell devices (FTDI FT232BM based) : DGQG and DUSB01
module.  PIDs were missing.
Signed-off-by: NGaetan Carlier <gcpatch@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: ftdi_sio: Add 0x5050/0x0900 USB IDs (Papouch Quido USB 4/4)
Signed-off-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.

Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: NLex V. Ross <lross@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Patch adds support for Luminance Stellaris Evaluation/Development
Kits (FTDI 2232C based).
The PIDs were missing.

Successfully tested with a Stellaris LM3S8962 Evaluation kit.
Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB product id registration for the ELV HS485 USB adapter (www.elv.de) to
their home automation bus system. Applies to 2.6.26.
Signed-off-by: NAndre Schenk <andre@melior.s.bawue.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.

The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.

(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=ed22 Rev= 5.00
S:  Manufacturer=FTDI
S:  Product=MixW RigExpert Tiny
S:  SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
)

From: Jon K Hellan <hellan@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.

A small number of units have been shipped early 2008
with a faulty USB Descriptor.  Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: NR. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch reverts 57833ea6
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.

Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add more usb device ids to the ftdi driver.

From: Peter Mack <Peter.Mack@scs-ptc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: NMirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.

The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: NKevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors

There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.

I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.

I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: NHarald Welte <laforge@openmoko.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.

Cc: stable <stable@kernel.org>
Signed-off-by: NEd Beroset <beroset@mindspring.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.

From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>