The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose.  The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.

This patch removes the last traces of this mechanism.

Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit.  With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000.  Oops.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

It is only included by signal_32.c
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Currently we set the kernel entry point and the address of the text
section in the Makefile, using CONFIG_KERNEL_START.

But we've already got <asm/page.h> in the linker script, so we can just
use KERNELBASE directly. That means if we ever change KERNELBASE there's
one less place to change it.

And we can set the entry point with ENTRY().

There are zero differences from "readelf -a vmlinux" with or without this
patch.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

There's some debugging in prom.c that wraps nastly on 80 character
terminals, reformat it to fit.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

Move pSeries specific code in set_dabr() into a ppc_md function, this will
allow us to keep plpar_wrappers.h private to platforms/pseries.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since
cell wants them as well as pseries (and chrp can use rtas-proc.c too,
at least in principle).  rtas_fw.c is gone, with its bits moved into
rtas_flash.c and rtas.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This section of code calls .audit_syscal_exit, but is inside CONFIG_AUDIT,
so it will fail to build if CONFIG_AUDITSYSCALL is not defined.

After discussion with David Woodhouse, change the ifdef to
CONFIG_AUDITSYSCALL
Signed-off-by: NHorms <horms@verge.net.au>
Acked-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This simplifies the macros which are different between 32-bit and
64-bit.  It also fixes a couple of printks on the bug->line element,
which is now a long.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A couple of instances of "i" that needed to be changed to "cpu_id"
got missed in the merge, because they were in CONFIG_TAU code.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKelly Daly <kelly@au.ibm.com>

Signed-off-by: NKelly Daly <kelly@au.ibm.com>

Signed-off-by: NKelly Daly <kelly@au.ibm.com>

Signed-off-by: NKelly Daly <kelly@au.ibm.com>

Signed-off-by: NKelly Daly <kelly@au.ibm.com>

Here's a revised version.  This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch).  In fact it is used in the powermac interrupt code
(but not on pSeries).

- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
  instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S

- ppc32 previously used a full "sync" barrier at the end of
  test_and_*_bit(), whereas ppc64 used an "isync".  The merged version
  uses "isync", since I believe that's sufficient.

- The ppc64 versions of then minix_*() bitmap functions have changed
  semantics.  Previously on ppc64, these functions were big-endian
  (that is bit 0 was the LSB in the first 64-bit, big-endian word).
  On ppc32 (and x86, for that matter, they were little-endian.  As far
  as I can tell, the big-endian usage was simply wrong - I guess
  no-one ever tried to use minixfs on ppc64.

- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
  inline (they were already out-of-line on ppc64).

- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
  the merged bitops.  What it was doing in mmu_context.h in the first
  place, I have no idea.

- The fls() function is now implemented using the cntlzw instruction
  on ppc64, instead of generic_fls(), as it already was on ppc32.

- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
  arch/ppc/Makefile.  This in turn requires some changes to
  arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.

Built and running on G5.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Cell uses the same code as pSeries for flashing the firmware
through rtas, so the implementation should not be part of
platforms/pseries.

Put it into arch/powerpc/kernel instead.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The official name for BPA is now CBEA (Cell Broadband
Engine Architecture). This patch renames all occurences
of the term BPA to 'Cell' for easier recognition.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

By parsing the command line earlier, we can add the mem= value to the
flattened device tree and let the generic code sort out the memory limit
for us.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line.  This puts the declaration
in system.h and the definition in mem.c.  This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes a bug where settimeofday would set the wrong parameters
in do_gtod, resulting in gettimeofday returning a value about 4
hours after the correct time.  The bug was that we divided a
negative 64-bit value with do_div, which treated it as unsigned
and gave us a result that was approximately 1.8e10 too large
(since the divisor was 1e9).
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Somehow we ended up with an #ifdef CONFIG_PPC64 around the export
of cur_cpu_spec, but raid6 as a module needs it on ppc32 as well
as ppc64.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

remove duplicate local variable, saves 2 asm instructions.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The merged version follows the ppc64 version pretty closely mostly,
and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version.
The main difference for ppc64 is that the 'p' command to call
show_state (which was always pretty dodgy) has been replaced by
the ppc32 'p' command, which calls a given procedure (so in fact
the old 'p' command behaviour can be achieved with 'p $show_state').
Signed-off-by: NPaul Mackerras <paulus@samba.org>

... for consistency with 64-bit.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This allows us to also use entry_64.S from the merged tree and reverts
the setup_64.c part of fda262b8.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Since I sent the patch to purge bootinfo.h from ARCH=powerpc and
ARCH=ppc64, setup-common.c has come into existence, and another
#include of bootinfo.h slipped in.  This patch removes it.  It also
removes include/asm-ppc64/bootinfo.h, which somehow survived the
previous patch which was supposed to remove it.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

For the current time idle_6xx only applies to 6xx ppc32 CPUs
Signed-off-by: NKumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

... which is needed now that ARCH=ppc64 is using the merged
setup_64.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On 32-bit platforms, these convert from kernel virtual addresses
to real (physical addresses), like tophys/tovirt but they use
the same register for the source and destination.  On 64-bit
platforms, they do nothing because the hardware ignores the top
two bits of the address in real mode.

These new macros are used in fpu.S now.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Untested, but "should" work...  at least this way it compiles.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

With ARCH=powerpc we assume the presence of a device tree, so we don't
require any support for the old bi_recs method of passing boot
parameters.  Likewise, we've never needed it for ppc64, but we still
had an include/asm-ppc64/bootinfo.h from which nothing was used.  This
patch removes that file, and all references to it in arch/ppc64 and
arch/powerpc.  A related, unused variable 'boot_mem_size' is also
removed from setup_32.c.  The bootinfo stuff remains in ARCH=ppc for
the time being.

Built and booted on Power5 (ARCH=ppc64 and ARCH=powerpc), built for
32-bit powermac (ARCH=powerpc and ARCH=ppc).
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y.  FP registers could be corrupted,
leading to strange random application crashes.

The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU.  However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit.  This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.

While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S.  The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.

Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.

Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

and use setup_64.c from the merged tree instead.  The only difference
between them was the code to set up the syscall maps.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>