The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage.  However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd.  Fix by passing the card's
ocr value which does not have the flag.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver may not be able to set the power correctly but that
is not a reason to BUG().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default.  Change it to the standard default
50 Ohm value.

The patch applies to v4.2+ except the file name changed.  It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit cc4f414c ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode.  While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: NWenkai Du <wenkai.du@intel.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There are no in-kernel users of the MVSDIO platform data method
(instantiating from a board file) so just delete this code and
make this a DT-only driver. We depend on OF and check that we have
an OF node in probe().

Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This platform data struct is only used inside the MVSDIO driver,
nowhere else in the entire kernel. Move the struct into the
driver and delete the external header.

Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
	u32 vvn;

	vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
	vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
	if (vvn == VENDOR_V_22)
		host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;

	if (vvn > VENDOR_V_22)
		host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}

This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The atmci_convert_chksize() function is no more valid for controller
version 0x600 due to the introduction of '2 data' chunk size.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

atmel-mci-regs.h is only included in atmel-mci.c so move its content in
the driver and do some cleanup in these definitions to remove checkpatch
errors.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc pm notifiers were recently reworked, but the new
code produces a lot of warnings when CONFIG_PM_SLEEP is disabled:

In file included from ../drivers/mmc/core/sdio_bus.c:27:0:
drivers/mmc/core/core.h:97:13: warning: 'mmc_register_pm_notifier' defined but not used [-Wunused-function]

The obvious solution is to add the 'inline' keyword at the
function definition, as it should be for any function defined
in a header file.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 0e40be7c20e0 ("mmc: core: Refactor code to register the MMC PM notifier")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Acked-by: NDong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:

../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
    (void *)pdata->slave_id_tx :
    ^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
    (void *)pdata->slave_id_rx;

This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.

The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This is a trivial patch which fixes printed strings split across two
or more lines in the source. I tried to grep for some error output*,
but I couldn't find it easily because it was broken across multiple
lines. This patch makes my life easier.

* in particular "Timeout waiting for hardware interrupt."
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_pwrseq_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The data in the SoC description structures is static and can therefore
reside in read-only memory.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add runtime PM support and use runtime_force_suspend|resume() for system
PM.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use kmalloc instead of kzalloc, as zeroing the memory isn't needed.
Signed-off-by: Nyalin wang <yalin.wang2010@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Turn the informative message about no vmmc/vqmmc regulator found in
debug one. There is no need to indicate that something optional is
missing. Moreover, it can bring confusion, people who doesn't know
it is optional may consider these messages as warnings or errors.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

_mmc_detect_card_removed() validates that the card is removable, but when
being called via the bus_ops ->detect() callbacks, the validation is
redundant as it's already done in mmc_rescan().

Move the validation of a removable card to the mmc_detect_card_removed()
API, which is where it's applicable, to allow the blk error recovery path
to get the response a bit earlier.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.

In mmc_rescan(), the ->card_event() and the ->get_cd() callback are being
invoked without claiming the host, let's fix this.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ->card_event() callback may be called when re-scan is disabled and for
non-removable cards, which both cases are unnecessary.

Instead let's move the call later in mmc_rescan() where these constraints
have been validated.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".

This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Anytime a write operation is performed with Reliable Write flag enabled,
the eMMC device is enforced to bypass the cache and do a write to the
underling NVM device by Jedec specification; this causes a performance
penalty since write operations can't be optimized by the device cache.

In our tests, we replayed a typical mobile daily trace pattern and found
~9% overall time reduction in trace replay by using this patch. Also the
write ops within 4KB~64KB chunk size range get a 40~60% performance
improvement by using the patch (as this range of write chunks are the ones
affected by REQ_META).

This patch has been discussed in the Mobile & Embedded Linux Storage Forum
and it's the results of feedbacks from many people. We also checked with
fsdevl and f2fs mailing list developers that this change in the usage of
REQ_META is not affecting FS behavior and we got positive feedbacks.
Reporting here the feedbacks:
http://comments.gmane.org/gmane.linux.file-systems/97219
http://thread.gmane.org/gmane.linux.file-systems.f2fs/3178/focus=3183Signed-off-by: NBruce Ford <bford@micron.com>
Signed-off-by: NLuca Porzio <lporzio@micron.com>
Fixes: ce39f9d1 ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If NO_DMA=y:

    ERROR: dma_unmap_sg [drivers/mmc/host/android-goldfish.ko] undefined!
    ERROR: dma_alloc_coherent [drivers/mmc/host/android-goldfish.ko] undefined!
    ERROR: dma_map_sg [drivers/mmc/host/android-goldfish.ko] undefined!
    ERROR: dma_free_coherent [drivers/mmc/host/android-goldfish.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

drivers/mmc/host/mtk-sd.c: In function ‘get_best_delay’:
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.start’ is used uninitialized in this function
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.maxlen’ is used uninitialized in this function

If delay is zero, these fields are indeed not initialized.
Let the compiler preinitialize the whole struct to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS).  The problem is that it does that
using the timing settings of the previous mode.  That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() begins with the card and host in HS200 mode.
Therefore, any commands sent to the card should use HS200 timing.
It is incorrect to set the host to High Speed (HS) timing before
sending the switch command.  Doing so is unreliable because
the timing parameters for HS mode are tighter than the timing
parameters for HS200 mode.  Thus the HS timings should be set
only after the card has switched mode.

However, it is not unreasonable first to reduce the frequency to
the HS mode frequency, which should make the switch command and
subsequent CMD13 commands more reliable.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently mmc_select_hs200() uses __mmc_switch() which checks the
success of the switch to HS200 mode using CMD13 (SEND_STATUS).
The problem is that it does that using the timing settings of legacy
mode.  That is prone to error, not least because the timing parameters
for legacy mode are tighter than the timing parameters for HS200 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs200() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.

A complication is that the caller, mmc_select_timing(), will ignore a
switch error (indicated by -EBADMSG), assume the old mode is valid
and continue, so the old timing must be restored in that case.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit converting pxamci to slot-gpio API inverted the logic of the
read-only gpio. Fix it by inverting the logic again.

Fixes: fd546ee6 ("mmc: pxamci: fix card detect with slot-gpio API")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

According to DesignWare DoC file, CardThreshold bit should be
bit[27:16].
So it's correct to use (0xFFF << 16), not (0x1FFF << 16).
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>