This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.

The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.

Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Most of the omap1 MMC boards got broken by an earlier patch
138ab9f8. If you look closely,
the MMC init funtions are pretty much just stubs.

Remove broken init code to make room for cleaner MMC init code.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds some new pin multiplexing options
for McBSP and McSPI from Arun KS. Also add two more
GPIOs from David Brownell.

Also mark omap24xx_cfg_reg() static.
Signed-off-by: NArun KS <arunks@mistralsolutions.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for basic features: uarts, i2c,
and rtc. Also includes defconfig.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

SDMA channel is not disabled after transaction error. So explicitly disable it.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked By : Nishant kamat <nskamat@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add Ethernet device support in board-ldp.c to make ldp can boot and mount
nfs successfully.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>

- Simplify function omap_i2c_mux_pins
- Add OMAP34xx pin multiplexing for busses 1 - 3
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In the case of spurious interrupt, the handler for previous interrupt
handler needs to flush posted writes with a read back of the interrupt
ack register. Warn about handlers that need to flush posted writes.
Signed-off-by: NTony Lindgren <tony@atomide.com>

The GPTIMER TLDR register does not need to be written if the GPTIMER
is not in autoreload mode.  This is the usual case for dynamic tick-enabled
kernels.

Simulation data indicate that skipping the read that occurs as part of
the write should save at least 300-320 ns for each GPTIMER1 timer
reprogram.  (This assumes L4-Wakeup is at 19MHz and GPTIMER write
posting is enabled.)  Skipping the write itself probably won't have
much impact since it should be posted on the OCP interconnect.

Tested on 2430SDP and 3430SDP.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap_dm_timer_write_reg() already waits for pending writes to complete,
so the extra wait in omap_dm_timer_set_load() is superfluous.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Declare the two 1Kbit EEPROMs included in the H4 board stack.
One is on the CPU card; the other is on the mainboard.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

system_rev is meant for board revision, this patch changes
all relevant instances to use the new omap_rev() function
liberating system_rev to be used with ATAG_REVISION as it
has been designed.
Signed-off-by: NLauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

At some point omap2 changed the bits for GET_OMAP_CLASS, which
broke 15xx detection on 730 as noticed by Russell King.

This patch fixes omap2 cpu detection to respect the original
GET_OMAP_CLASS, and simplifies the detection for 34xx.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rename omap2_check_revision to omap24xx_check_revision.
Then next patch will split if further and add omap34xx_check_revision.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Help OSK work better with root-on-CF, by having one of the LEDs
use the "ide-disk" trigger (to kick in during CF I/O).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

List the 4 Kbit I2C EEPROM included on the Mistral board.

Also add a comment about the hardware workaround needed to
properly support the WAKE button.  More info at

  http://elinux.org/OSK_Mistral_wakeup_button_mod

Still no support for the (optional) camera sensor.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Switch to gpio_request/free calls
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Minor GPIO fixes:

 - If get_gpio_bank() fails, then BUG() out.

 - In omap_set_gpio_debounce():
    * protect the read/modify/write with the relevant spinlock
    * make the omap3 clock ops pass "sparse" checking

Except for the spinlock problem, these were reported through "make".
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Clean up OMAP GPIO request/free functions

 - Rename and declare static OMAP specific GPIO request/free functions
 - Register them into gpiolib as chip-specific hooks
 - Add omap_request_gpio/omap_free_gpio wrappers for existing code not
   converted yet to use gpiolib
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
[ dbrownell@users.sourceforge.net: remove needless check_gpio() calls ]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.

(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

More conversion to the standard GPIO interfaces:  stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.

Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.

 - For the call sites which defined an initial value either
   before or after setting the direction, that value was used.

   When that value was previously assigned afterwards, this
   could eliminate a brief output glitch ... and possibly
   change behavior.  In a few cases (LCDs) several values
   were assigned together ... those were re-arranged to match
   the explicit sequence provided.

 - Some call sites didn't define such a value; so I chose an
   initial "off/reset" value that seemed to default to "off".

In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.

The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.

Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script.  Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There are already various drivers having bigger label than 10 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.

Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.

This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Give the correct size when reserving the interrupt vector table.  It should be
a page not a single byte.
Signed-off-by: NAkira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the preemption resume_kernel() routine by inverting the test to see
whether interrupts are off (IM7 is all enabled, not all disabled).

Furthermore, interrupts should be disabled on entry to resume_kernel() so that
they're correctly set for jumping to restore_all() and doing the need
reschedule test.
Signed-off-by: NAkira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Discard low-prioriy Tx interrupts when closing an MN10300 on-chip serial port.

The MN10300 on-chip serial port uses three interrupts to manage its serial
ports:

 (1) A very high priority interrupt that drives virtual DMA for Rx.

 (2) A very high priority interrupt that drives virtual DMA for Tx.

 (3) A normal priority virtual interrupt that does the normal UART interrupt
     stuff and is shared between Rx and Tx.

mn10300_serial_stop_tx() only disables the high priority Tx interrupt.  It
doesn't also disable the normal priority one because it is shared with Rx.

However, the high priority interrupt may interrupt local_irq_disabled()
sections, and so may have queued up a low priority virtual interrupt whilst the
UART driver is asking for the Tx interrupt to be disabled.

The result of this can be an oops when we try to process the interrupt in
mn10300_serial_transmit_interrupt() as port->uart.info and port->uart.info->tty
may have gone away.

To deal with this, if either of those pointers is NULL, we make sure the
high-priority Tx interrupt is disabled and discard the interrupt.  The low
priority interrupt is disabled by the mn10300_serial_pic irq_chip table.
Signed-off-by: NAkira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Include the linux/page.h header into the MN10300 kernel linker script thus
allowing us to use PAGE_SIZE macro instead of a numeric constant.

Also use the PERCPU macro instead of an explicit section definition.
Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mconsole_init() passed 256 bytes as length in os_create_unix_socket, while
the sizeof UNIX_PATH_MAX is 108. This patch fixes that problem and avoids
a big overrun bug reported on UML bootup.

sockaddr_un.sun_path is UNIX_PATH_MAX long which causes the problem.
Reported-by: NVikas K Managutte <vikki.km@gmail.com>
Reported-by: NSarvesh Kumar Lal Das <skldas@gmail.com>
Signed-off-by: NBalbir Singh <balbir@linux.vnet.ibm.com>
Reviewed-by: NPekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: NWANG Cong <wangcong@zeuux.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>		[please check with Jeff]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented.  This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.

Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

With the introduction of the generic affinity autoselector,
irq_select_affinity(), IRQs are now being retargetted,
using a default mask, via the request_irq() path.
This results in all IRQs targetted at CPU 0.

SN Altix assigns affinity in the SN PROM, and does not
expect that to be changed as part of request_irq().

Set the IRQ_AFFINITY_SET flag to prevent
request_irq() from resetting affinity.
Signed-off-by: NJohn Keller <jpk@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The generic_defconfig has three section mismatches.  This clears
arch_unregister_cpu()
Signed-off-by: NRobin Holt <holt@sgi.com>
Signed-off-by: NJack Steiner <steiner@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The generic_defconfig has three section mismatches.  This clears up
sn_check_wars().
Signed-off-by: NRobin Holt <holt@sgi.com>
Signed-off-by: NJack Steiner <steiner@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The AUTOFS=y and AUTOFS4=y causes problems with some distros versions of
automount.  I turned both of those to =m and then followed the default
prompts for everything else.  I did notice that CONFIG_PNP_DEBUG got
changed to CONFIG_PNP_DEBUG_MESSAGES and the default was a =y so I turned
that back to a =n.
Signed-off-by: NRobin Holt <holt@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

As noted by Akinobu Mita in patch b1fceac2,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory.  Thus a NULL test or memset after calls to these
functions is unnecessary.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

CC      arch/ia64/kernel/asm-offsets.s
In file included from include/linux/bitops.h:17,
                 from include/linux/kernel.h:15,
                 from include/linux/sched.h:52,
                 from arch/ia64/kernel/asm-offsets.c:9:
arch/ia64/include/asm/bitops.h: In function 'set_bit':
arch/ia64/include/asm/bitops.h:47: error: implicit declaration of function 'BUILD_BUG_ON'

Obvious inclusion of kernel.h doesn't fix it, because of circular dependencies
involving fls.h and log2(). Fixing the latter requires some serious header surgery,
it seems, so just remove BUILD_BUG_ON for now.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

these warnings:

  arch/x86/kernel/paravirt-spinlocks.c: In function ‘default_spin_lock_flags’:
  arch/x86/kernel/paravirt-spinlocks.c:12: warning: passing argument 1 of ‘__raw_spin_lock’ from incompatible pointer type
  arch/x86/kernel/paravirt-spinlocks.c: At top level:
  arch/x86/kernel/paravirt-spinlocks.c:11: warning: ‘default_spin_lock_flags’ defined but not used

showed that the prototype of default_spin_lock_flags() was confused about
what type spinlocks have.

the proper type on UP is raw_spinlock_t.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: minor fix
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>