This follows the way of handling other flashes and cleans code a bit. As
next task we will want to move flash code to ChipCommon driver as:
1) Flash controllers are accesible using ChipCommon registers
2) This code isn't MIPS specific
This change prepares bcma for that.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Most of info stored in this struct wasn't really used anywhere as we put
all that data in platform data & resource as well.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's another SoC with 32 GPIOs and simplified watchdog handling. It was
tested on D-Link DIR-885L.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On recent Broadcom chipsets PMU is present as separated core and it
can't be accessed using ChipCommon anymore as it fails with e.g.:
[    0.000577] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf1000604

Solve it by using a new (PMU) core pointer set to ChipCommon or PMU
depending on the hardware capabilities.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

PMU (Power Management Unit) seems to be a separated piece of hardware,
just accessed using ChipCommon core registers. In recent Broadcom
chipsets PMU is not bounded to CC but available as separated core.

To make code cleaner & easier to review (for a correct R/W access) use
clearer names.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add missing defines and print proper names.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The field bcma_nflash::mtd is never set to be non-zero anywhere, but we
test for it in the removal path. So the MTD is never unregistered.

Also, we should use nand_release(), not mtd_device_unregister().

Finally, we don't need to use the 'platdata' for stashing/retrieving our
*driver* data -- that's what *_{get,set}_drvdata() are for.

So, kill off bcm_nflash::mtd, and stash the struct bcm47xxnflash in
drvdata instead. Also move the forward declaration of mtd_info up a bit,
since struct bcma_sflash should be using it.

Caught while inspecting other changes being made to this driver. Compile
tested only.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: linux-wireless@vger.kernel.org
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

This patch adds support for the BCM4365 and BCM4366 11ac Wave2
PCIE devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This switches the BCMA GPIO driver to use GPIOLIB_IRQCHIP to
handle its interrupts instead of rolling its own copy of the
irqdomain handling etc.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This makes it possible to save some lines of code in drivers with an
simple bcma driver registration.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It isn't required for bcma bus on SoCs, so provide some empty functions
and allow disabling it.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function isn't really related to any bus core. It touches PCI
device config registers only, so move it to the (PCI) host file.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These functions are not exported nor used anywhere, so there is no
reason to put them in public headers.
Also drop unused bcma_chipco_(suspend|resume).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We were providing declarations but actual code was compiled only with
CONFIG_BCMA_HOST_PCI set. This could result in:
ERROR: "bcma_host_pci_down" [drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko] undefined!
ERROR: "bcma_host_pci_up" [drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko] undefined!
ERROR: "bcma_host_pci_down" [drivers/net/wireless/b43/b43.ko] undefined!
ERROR: "bcma_host_pci_up" [drivers/net/wireless/b43/b43.ko] undefined!
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It doesn't operate on PCI core, but PCI host device, so there is no
point of passing core related struct.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Bringing PCIe hosted bus up requires operating on host-related core.
Since we plan to support PCIe Gen 2 devices we should provide a helper
picking the correct one (PCIE or PCIE2).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is stil incomplete, so we don't add PCI IDs of new devices yet.
Purpose of this patch is to allow testing & adjusting rest of the code.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are some PCIe core fixes that need to be applied before accessing
SPROM, otherwise reading it may fail.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done
a bit later, with memory allocator available. This allows us to simplify
code by using standard bus scanning method.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This moves bcma_core_irq() to main.c and add a extra parameter with a
number so that we can return different irq number for devices with more
than one.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver is used by the bcm53xx ARM SoC code. Now it is possible to
give the address of the chipcommon core in device tree and bcma will
search for all the other cores.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This core is used on BCM4708 to configure the PCIe and USB3 PHYs and it
contains the addresses to the Device Management unit. This will be used
by the PCIe driver first.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each core could have more than one alternative address. There are cores
with 8 alternative addresses for different functions. The PHY control
in the Chip common B core is done through the 2. alternative address
and not the first one.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
CC: linux-usb@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is required to split SoC bus init into two phases. The later one
(which includes scanning) should be called when kalloc is available.

Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change is important for SoC host. In future we will want to know
chip ID (needed for early MIPS boot) before doing cores scanning.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is an ongoing work on cleaning MIPS's nvram support so it could be
re-used on other platforms (bcm53xx to say precisely).
This will require a bit of extra logic in bcma this patch implements.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's cleaner and we don't have quite identical names like
BCMA_CORE_PCIEG2 and BCMA_CORE_PCIE2.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It contains radio 0x2057 rev 14 just like a BCM43217, so it doesn't
require any magic. The main difference is that BCM4313 is 1x1:1.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By the way add few chipsets that were tracked with "wl" dumps.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be
initialized differently.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Input GPIO changes can generate interrupts, but we need kind of ACK for
them by changing IRQ polarity. This is required to stop hardware from
keep generating interrupts and generate another one on the next GPIO
state change.
This code allows using GPIOs with standard interrupts and add for
example GPIO buttons support.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6216/

This function is used to get a specific core when there is more than
one core of that specific type. This is used in bgmac to reset all GMAC
cores.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the bcma_core_pci_power_save() call from
the bcma_core_pci_{up,down}() functions as it tries to schedule
thus requiring to call them from non-atomic context. The function
bcma_core_pci_power_save() is now exported so the calling module
can explicitly use it in non-atomic context. This fixes the
'scheduling while atomic' issue reported by Tod Jackson and
Joe Perches.

[   13.210710] BUG: scheduling while atomic: dhcpcd/1800/0x00000202
[   13.210718] Modules linked in: brcmsmac nouveau coretemp kvm_intel kvm cordic brcmutil bcma dell_wmi atl1c ttm mxm_wmi wmi
[   13.210756] CPU: 2 PID: 1800 Comm: dhcpcd Not tainted 3.11.0-wl #1
[   13.210762] Hardware name: Alienware M11x R2/M11x R2, BIOS A04 11/23/2010
[   13.210767]  ffff880177c92c40 ffff880170fd1948 ffffffff8169af5b 0000000000000007
[   13.210777]  ffff880170fd1ab0 ffff880170fd1958 ffffffff81697ee2 ffff880170fd19d8
[   13.210785]  ffffffff816a19f5 00000000000f4240 000000000000d080 ffff880170fd1fd8
[   13.210794] Call Trace:
[   13.210813]  [<ffffffff8169af5b>] dump_stack+0x4f/0x84
[   13.210826]  [<ffffffff81697ee2>] __schedule_bug+0x43/0x51
[   13.210837]  [<ffffffff816a19f5>] __schedule+0x6e5/0x810
[   13.210845]  [<ffffffff816a1c34>] schedule+0x24/0x70
[   13.210855]  [<ffffffff816a04fc>] schedule_hrtimeout_range_clock+0x10c/0x150
[   13.210867]  [<ffffffff810684e0>] ? update_rmtp+0x60/0x60
[   13.210877]  [<ffffffff8106915f>] ? hrtimer_start_range_ns+0xf/0x20
[   13.210887]  [<ffffffff816a054e>] schedule_hrtimeout_range+0xe/0x10
[   13.210897]  [<ffffffff8104f6fb>] usleep_range+0x3b/0x40
[   13.210910]  [<ffffffffa00371af>] bcma_pcie_mdio_set_phy.isra.3+0x4f/0x80 [bcma]
[   13.210921]  [<ffffffffa003729f>] bcma_pcie_mdio_write.isra.4+0xbf/0xd0 [bcma]
[   13.210932]  [<ffffffffa0037498>] bcma_pcie_mdio_writeread.isra.6.constprop.13+0x18/0x30 [bcma]
[   13.210942]  [<ffffffffa00374ee>] bcma_core_pci_power_save+0x3e/0x80 [bcma]
[   13.210953]  [<ffffffffa003765d>] bcma_core_pci_up+0x2d/0x60 [bcma]
[   13.210975]  [<ffffffffa03dc17c>] brcms_c_up+0xfc/0x430 [brcmsmac]
[   13.210989]  [<ffffffffa03d1a7d>] brcms_up+0x1d/0x20 [brcmsmac]
[   13.211003]  [<ffffffffa03d2498>] brcms_ops_start+0x298/0x340 [brcmsmac]
[   13.211020]  [<ffffffff81600a12>] ? cfg80211_netdev_notifier_call+0xd2/0x5f0
[   13.211030]  [<ffffffff815fa53d>] ? packet_notifier+0xad/0x1d0
[   13.211064]  [<ffffffff81656e75>] ieee80211_do_open+0x325/0xf80
[   13.211076]  [<ffffffff8106ac09>] ? __raw_notifier_call_chain+0x9/0x10
[   13.211086]  [<ffffffff81657b41>] ieee80211_open+0x71/0x80
[   13.211101]  [<ffffffff81526267>] __dev_open+0x87/0xe0
[   13.211109]  [<ffffffff8152650c>] __dev_change_flags+0x9c/0x180
[   13.211117]  [<ffffffff815266a3>] dev_change_flags+0x23/0x70
[   13.211127]  [<ffffffff8158cd68>] devinet_ioctl+0x5b8/0x6a0
[   13.211136]  [<ffffffff8158d5c5>] inet_ioctl+0x75/0x90
[   13.211147]  [<ffffffff8150b38b>] sock_do_ioctl+0x2b/0x70
[   13.211155]  [<ffffffff8150b681>] sock_ioctl+0x71/0x2a0
[   13.211169]  [<ffffffff8114ed47>] do_vfs_ioctl+0x87/0x520
[   13.211180]  [<ffffffff8113f159>] ? ____fput+0x9/0x10
[   13.211198]  [<ffffffff8106228c>] ? task_work_run+0x9c/0xd0
[   13.211202]  [<ffffffff8114f271>] SyS_ioctl+0x91/0xb0
[   13.211208]  [<ffffffff816aa252>] system_call_fastpath+0x16/0x1b
[   13.211217] NOHZ: local_softirq_pending 202

The issue was introduced in v3.11 kernel by following commit:

commit aa51e598
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sat Aug 24 00:32:31 2013 +0200

    brcmsmac: use bcma PCIe up and down functions

    replace the calls to bcma_core_pci_extend_L1timer() by calls to the
    newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
    Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fix has been discussed with Hauke Mehrtens [1] selection
option 3) and is intended for v3.12.

Ref:
[1] http://mid.gmane.org/5239B12D.3040206@hauke-m.de

Cc: <stable@vger.kernel.org> # 3.11.x
Cc: Tod Jackson <tod.jackson@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables or disables power saving on the PCIe bus when the wifi is
in operation or not.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not called any more, do not export it.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wifi driver should tell the PCIe core that it is now in operation
so that some workarounds can be applied and the power state is changed.
This should replace the call to bcma_core_pci_extend_L1timer by the
brcmsmac driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are the chipIDs of some ARM based SoCs from the BCM47xx line.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>