Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 3 年多

通知 13
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 04 9月, 2008 2 次提交
  3. 03 9月, 2008 2 次提交
    • L
      Split up PIT part of TSC calibration from native_calibrate_tsc · ec0c15af
      由 Linus Torvalds 提交于 
      The TSC calibration function is still very complicated, but this makes
it at least a little bit less so by moving the PIT part out into a
helper function of its own.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-of-by: NLinus Torvalds <torvalds@linux-foundation.org>
      ec0c15af
    • T
      [x86] Fix TSC calibration issues · fbb16e24
      由 Thomas Gleixner 提交于 
      Larry Finger reported at http://lkml.org/lkml/2008/9/1/90:
An ancient laptop of mine started throwing errors from b43legacy when
I started using 2.6.27 on it. This has been bisected to commit bfc0f594
"x86: merge tsc calibration".

The unification of the TSC code adopted mostly the 64bit code, which
prefers PMTIMER/HPET over the PIT calibration.

Larrys system has an AMD K6 CPU. Such systems are known to have
PMTIMER incarnations which run at double speed. This results in a
miscalibration of the TSC by factor 0.5. So the resulting calibrated
CPU/TSC speed is half of the real CPU speed, which means that the TSC
based delay loop will run half the time it should run. That might
explain why the b43legacy driver went berserk.

On the other hand we know about systems, where the PIT based
calibration results in random crap due to heavy SMI/SMM
disturbance. On those systems the PMTIMER/HPET based calibration logic
with SMI detection shows better results.

According to Alok also virtualized systems suffer from the PIT
calibration method.

The solution is to use a more wreckage aware aproach than the current
either/or decision.

1) reimplement the retry loop which was dropped from the 32bit code
during the merge. It repeats the calibration and selects the lowest
frequency value as this is probably the closest estimate to the real
frequency

2) Monitor the delta of the TSC values in the delay loop which waits
for the PIT counter to reach zero. If the maximum value is
significantly different from the minimum, then we have a pretty safe
indicator that the loop was disturbed by an SMI.

3) keep the pmtimer/hpet reference as a backup solution for systems
where the SMI disturbance is a permanent point of failure for PIT
based calibration

4) do the loop iteration for both methods, record the lowest value and
decide after all iterations finished.

5) Set a clear preference to PIT based calibration when the result
makes sense.

The implementation does the reference calibration based on
HPET/PMTIMER around the delay, which is necessary for the PIT anyway,
but keeps separate TSC values to ensure the "independency" of the
resulting calibration values.

Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6
(affected machine with a double speed pmtimer which I grabbed out of
the dump), Pentium class machines and AMD/Intel 64 bit boxen.
Bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      fbb16e24
  5. 25 8月, 2008 2 次提交
  7. 18 8月, 2008 1 次提交
  9. 16 7月, 2008 1 次提交
  11. 11 7月, 2008 1 次提交
  13. 09 7月, 2008 6 次提交